Content .. 119 120 121 122 ..

Nissan Juke (2012 year). Service Repair Manual - part 121

TURN SIGNAL LAMP CIRCUIT

EXL-65

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

EXL

YES

>> Check each bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer

BCS-80, "Removal and Installation"

(with Intelligent Key),

BCS-141, "Removal and Installation"

(without Intelligent Key).

>> Repair or replace harness.

CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT

Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp and ground.

Front turn signal lamp

Side turn signal lamp

Rear turn signal lamp

Is the inspection result normal?

YES

>> Check corresponding bulb socket and harness. Repair or replace if necessary.

>> Repair or replace harness.

Front turn signal lamp

Ground

Continuity

Connector

Terminal

E46

Existed

E27

Side turn signal lamp

Ground

Continuity

Connector

Terminal

E40

Existed

E23

Rear combination lamp

Ground

Continuity

Connector

Terminal

B59

Existed

B80

Revision: 2011 October

2012 JUKE

EXL-66

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

HAZARD SWITCH

HAZARD SWITCH

Component Function Check

INFOID:0000000007579208

CHECK HAZARD SWITCH SIGNAL BY CONSULT

CONSULT DATA MONITOR

Turn the ignition switch ON.

Select “HAZARD SW” of BCM (FLASHER) data monitor item.

With operating the hazard switch, check the monitor status.

Is the inspection result normal?

YES

>> Hazard switch circuit is normal.

>> Refer to

EXL-66, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000007579209

CHECK HAZARD SWITCH SIGNAL INPUT

Turn ignition switch OFF.

Disconnect hazard switch connector.

Check voltage between hazard switch connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> GO TO 2.

CHECK HAZARD SWITCH SIGNAL OPEN CIRCUIT

Disconnect BCM connector.

Check continuity between hazard switch harness connector and BCM harness connector.

*1: Without Intelligent Key

*2: With Intelligent Key

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace harness.

CHECK HAZARD SWITCH SIGNAL SHORT CIRCUIT

Check continuity between hazard switch harness connector and ground.

Is the inspection result normal?

Monitor item

Condition

Monitor status

HAZARD SW

Hazard switch

OFF

Off

(+)

(

−

)

Voltage (Approx.)

Hazard switch

Connector

Terminal

M45

Ground

12 V

Hazard switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

M45

M65

M68

Existed

Hazard switch

Ground

Continuity

Connector

Terminal

M45

Not existed

Revision: 2011 October

2012 JUKE

HAZARD SWITCH

EXL-67

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

EXL

YES

>> Replace BCM. Refer to

BCS-80, "Removal and Installation"

(With Intelligent Key) or

BCS-141,

"Removal and Installation"

(Without Intelligent Key).

>> Repair or replace harness.

CHECK HAZARD SWITCH GROUND OPEN CIRCUIT

Check continuity between hazard switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace hazard switch.

>> Repair or replace harness.

Hazard switch

Ground

Continuity

Connector

Terminal

M45

Existed

Revision: 2011 October

2012 JUKE

EXL-68

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

SYMPTOM DIAGNOSIS

EXTERIOR LIGHTING SYSTEM SYMPTOMS

WITHOUT DAYTIME RUNNING LIGHT SYSTEM

WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Symptom Table

INFOID:0000000007579210

NOTE:
Perform the self-diagnosis with CONSULT before symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.

Symptom

Possible cause

Inspection item

Headlamp (HI) is not
turned ON.

One side

• Fuse
• Halogen bulb
• Harness between IPDM E/R and

headlamp

• IPDM E/R

Headlamp (HI) circuit
Refer to

EXL-41, "Component

Function Check"

Both sides

Symptom diagnosis
“BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to

EXL-73, "Diagnosis Procedure"

High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.]

Combination meter

• Combination meter

Data monitor “HI-BEAM IND”

• BCM (HEADLAMP)

Active test “HEADLAMP”

Headlamp (LO) is not
turned ON.

One side

• Fuse
• Halogen bulb
• Harness between IPDM E/R and

headlamp

• IPDM E/R

Headlamp (LO) circuit
Refer to

EXL-43, "WITHOUT DAY-

TIME RUNNING LIGHT SYSTEM :
Component Function Check"

Both sides

Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to

EXL-74, "Diagnosis Procedure"

Headlamp is not turned
OFF.

When ignition switch
is turned ON.

When ignition switch
is turned OFF.

IPDM E/R

—

Headlamp HI and LO are not turned ON.

• Halogen bulb
• Harness between headlamp and

ground

Headlamp ground circuit
Refer to

EXL-48, "WITHOUT DAY-

TIME RUNNING LIGHT SYSTEM :
Diagnosis Procedure"

Headlamp is not turned ON/OFF with the lighting
switch AUTO.

• Combination switch
• Harness between combination

switch and BCM

• BCM

Combination switch
Refer to

BCS-78, "Symptom Table"

• Optical sensor
• Harness between optical sensor

and BCM

• BCM

Optical sensor
Refer to

EXL-58, "Component

Function Check"

Front fog lamp is not
turned ON.

One side

• Front fog lamp bulb
• Harness between IPDM E/R and

front fog lamp

• IPDM E/R

Front fog lamp circuit
Refer to

EXL-61, "Component

Function Check"

Both side

Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to

EXL-76, "Diagnosis Procedure"

Parking lamp is not turned ON.

• Parking lamp bulb
• Harness between IPDM E/R and

parking lamp

• IPDM E/R

Parking lamp circuit
Refer to

EXL-52, "Component

Function Check"

Revision: 2011 October

2012 JUKE

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-69

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXL

WITH DAYTIME RUNNING LIGHT SYSTEM

WITH DAYTIME RUNNING LIGHT SYSTEM : Symptom Table

INFOID:0000000007579211

NOTE:
Perform the self-diagnosis with CONSULT before symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.

Front side marker lamp is not turned ON.

• Front side marker lamp bulb
• Harness between IPDM E/R and

front side marker lamp

Front side marker lamp circuit
Refer to

EXL-54, "Component

Function Check"

Parking lamp and front side marker lamp are not
turned ON.

• Harness between IPDM E/R and

parking lamp

• IPDM E/R

Parking lamp circuit
Refer to

EXL-52, "Component

Function Check"

Tail lamp is not turned ON.

• Tail lamp bulb
• Harness between IPDM E/R and

rear combination lamp

Tail lamp circuit
Refer to

EXL-55, "Component

Function Check"

License plate lamp is not turned ON.

• License plate lamp bulb
• Harness between IPDM E/R and

license plate lamp

License plate lamp circuit
Refer to

EXL-57, "Component

Function Check"

Tail lamp and license plate lamp are not turned
ON.

Harness between IPDM E/R and
rear combination lamp

Tail lamp circuit
Refer to

EXL-55, "Component

Function Check"

• Parking lamp, front side marker lamp, tail lamp

and license plate lamp are not turned ON.

• Parking lamp, front side marker lamp, tail lamp

and license plate lamp are not turned OFF.

Symptom diagnosis
“PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE
NOT TURNED ON”
Refer to

EXL-75, "Diagnosis Procedure"

Tail lamp indicator is not turned ON.
(Exterior lamps are turned ON.)

Combination meter

• Combination meter

Data monitor “LIGHT IND”

• BCM (HEADLAMP)

Active test “TAIL LAMP”

Turn signal lamp does
not blink.

Indicator lamp is nor-
mal.
(Applicable side per-
forms the high flasher
activation.)

• Harness between BCM and each

turn signal lamp

• Turn signal lamp bulb

Turn signal lamp circuit
Refer to

EXL-63, "Component

Function Check"

Indicator lamp is in-
cluded.

• Combination switch
• Harness between combination

switch and BCM

• BCM

Combination switch
Refer to

BCS-78, "Symptom Table"

Turn signal indicator
lamp does not blink.
(Turn signal indicator
lamp is normal.)

One side

Combination meter

—

Both sides
(Always)

• Turn signal indicator lamp signal
- BCM
• Combination meter

• Combination meter

Data monitor “TURN IND”

• BCM (FLASHER)

Active test “FLASHER”

Both sides
(Only when activating
hazard warning lamp
with the ignition switch
OFF.)

• Combination meter power supply

and ground circuit

• Combination meter

Combination meter
Power supply and ground circuit
Refer to

MWI-42, "COMBINATION

METER : Diagnosis Procedure"

• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)

• Hazard switch
• Harness between hazard switch

and BCM

• BCM

Hazard switch
Refer to

EXL-66, "Component

Function Check"

Symptom

Possible cause

Inspection item

Revision: 2011 October

2012 JUKE

EXL-70

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

Symptom

Possible cause

Inspection item

Headlamp (HI) is not
turned ON.

One side

• Fuse
• Halogen bulb
• Harness between IPDM E/R and

headlamp

• IPDM E/R

Headlamp (HI) circuit
Refer to

EXL-41, "Component

Function Check"

Both sides

Symptom diagnosis
“BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to

EXL-73, "Diagnosis Procedure"

High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.]

Combination meter

• Combination meter

Data monitor “HI-BEAM IND”

• BCM (HEADLAMP)

Active test “HEADLAMP”

Headlamp (LO) is not
turned ON.

One side

• Fuse
• Halogen bulb
• Harness between IPDM E/R and

daytime running light relay 1

• Harness between daytime run-

ning light relay 1 and headlamp

• Daytime running light relay 1
• IPDM E/R

Headlamp (LO) circuit
Refer to

EXL-44, "WITH DAYTIME

RUNNING LIGHT SYSTEM : Com-
ponent Function Check"

Both sides

Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to

EXL-74, "Diagnosis Procedure"

Headlamp is not turned
OFF.

When ignition switch
is turned ON.

When ignition switch
is turned OFF.

IPDM E/R

—

Headlamp HI and LO are not turned ON.

• Halogen bulb
• Harness between headlamp and

daytime running light relay 2

• Harness between daytime run-

ning light relay 2 and ground

• Daytime running light relay 2

Headlamp ground circuit
Refer to

EXL-48, "WITHOUT DAY-

TIME RUNNING LIGHT SYSTEM :
Diagnosis Procedure"

Daytime running light is not turned ON.
[Headlamp (HI) is turned ON.]

• Fuse
• Harness between IPDM E/R and

daytime running light relay 2

• Daytime running light relay 2
• IPDM E/R
• BCM
• ECM
• Combination meter

• Daytime running light relay circuit

Refer to

EXL-50, "Component

Function Check"

• BCM (HEADLAMP)

Data monitor “ENGINE STATE”

• Combination mete

Data monitor “PKB SW”

• BCM (HEADLAMP)

Active test “DAYTIME RUNNING
LIGHT”

Head lamps (both HI and LO) turn ON in the dim-
ming status while daytime running light system is
ON.

Daytime running light relay 1

Daytime running light relay 1
Refer to

EXL-47, "WITH DAYTIME

RUNNING LIGHT SYSTEM : Com-
ponent Inspection"

Front fog lamp is not
turned ON.

One side

• Front fog lamp bulb
• Harness between IPDM E/R and

front fog lamp

• IPDM E/R

Front fog lamp circuit
Refer to

EXL-61, "Component

Function Check"

Both side

Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to

EXL-76, "Diagnosis Procedure"

Parking lamp is not turned ON.

• Parking lamp bulb
• Harness between IPDM E/R and

parking lamp

• IPDM E/R

Parking lamp circuit
Refer to

EXL-52, "Component

Function Check"

Revision: 2011 October

2012 JUKE

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-71

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXL

Front side marker lamp is not turned ON.

• Front side marker lamp bulb
• Harness between IPDM E/R and

front side marker lamp

Front side marker lamp circuit
Refer to

EXL-54, "Component

Function Check"

Parking lamp and front side marker lamp are not
turned ON.

• Harness between IPDM E/R and

parking lamp

• IPDM E/R

Parking lamp circuit
Refer to

EXL-52, "Component

Function Check"

Tail lamp is not turned ON.

• Tail lamp bulb
• Harness between IPDM E/R and

rear combination lamp

Tail lamp circuit
Refer to

EXL-55, "Component

Function Check"

License plate lamp is not turned ON.

• License plate lamp bulb
• Harness between IPDM E/R and

license plate lamp

License plate lamp circuit
Refer to

EXL-57, "Component

Function Check"

Tail lamp and license plate lamp are not turned
ON.

Harness between IPDM E/R and
rear combination lamp

Tail lamp circuit
Refer to

EXL-55, "Component

Function Check"

• Parking lamp, front side marker lamp, tail lamp

and license plate lamp are not turned ON.

• Parking lamp, front side marker lamp, tail lamp

and license plate lamp are not turned OFF.

Symptom diagnosis
“PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE
NOT TURNED ON”
Refer to

EXL-75, "Diagnosis Procedure"

Tail lamp indicator is not turned ON.
(Exterior lamps are turned ON.)

Combination meter

• Combination meter

Data monitor “LIGHT IND”

• BCM (HEADLAMP)

Active test “TAIL LAMP”

Turn signal lamp does
not blink.

Indicator lamp is nor-
mal.
(Applicable side per-
forms the high flasher
activation.)

• Harness between BCM and each

turn signal lamp

• Turn signal lamp bulb

Turn signal lamp circuit
Refer to

EXL-63, "Component

Function Check"

Indicator lamp is in-
cluded.

• Combination switch
• Harness between combination

switch and BCM

• BCM

Combination switch
Refer to

BCS-78, "Symptom Table"

Turn signal indicator
lamp does not blink.
(Turn signal indicator
lamp is normal.)

One side

Combination meter

—

Both sides
(Always)

• Turn signal indicator lamp signal
- BCM
• Combination meter

• Combination meter

Data monitor “TURN IND”

• BCM (FLASHER)

Active test “FLASHER”

Both sides
(Only when activating
hazard warning lamp
with the ignition switch
OFF.)

• Combination meter power supply

and ground circuit

• Combination meter

Combination meter
Power supply and ground circuit
Refer to

MWI-42, "COMBINATION

METER : Diagnosis Procedure"

• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)

• Hazard switch
• Harness between hazard switch

and BCM

• BCM

Hazard switch
Refer to

EXL-66, "Component

Function Check"

Symptom

Possible cause

Inspection item

Revision: 2011 October

2012 JUKE

EXL-72

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

NORMAL OPERATING CONDITION

NORMAL OPERATING CONDITION

Description

INFOID:0000000007579212

AUTO LIGHT SYSTEM

The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel,
sky bridge, shadowed area etc.) while using the auto light system. This causes the control difference. This is
normal.

Revision: 2011 October

2012 JUKE

BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON

EXL-73

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXL

BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON

Description

INFOID:0000000007579213

Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.

Diagnosis Procedure

INFOID:0000000007579214

COMBINATION SWITCH INSPECTION

Check the combination switch. Refer to

BCS-78, "Symptom Table"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning part.

CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

Select “HL HI REQ” of IPDM E/R data monitor item.

With operating the lighting switch, check the monitor status.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

>> Replace BCM. Refer to

BCS-80, "Removal and Installation"

(with Intelligent Key),

BCS-141,

"Removal and Installation"

(without Intelligent Key).

Monitor item

Condition

Monitor status

HL HI REQ

Lighting switch
(2ND)

HI or PASS

OFF

Revision: 2011 October

2012 JUKE

EXL-74

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON

BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON

Description

INFOID:0000000007579215

Both side headlamps (LO) are not turned ON in any condition.

Diagnosis Procedure

INFOID:0000000007579216

CHECK COMBINATION SWITCH

Check the combination switch. Refer to

BCS-78, "Symptom Table"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning part.

CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

Select “HL LO REQ” of IPDM E/R data monitor item.

With operating the lighting switch, check the monitor status.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

>> Replace BCM. Refer to

BCS-80, "Removal and Installation"

(with Intelligent Key),

BCS-141,

"Removal and Installation"

(without Intelligent Key).

Monitor item

Condition

Monitor status

HL LO REQ

Lighting switch

2ND

OFF

Revision: 2011 October

2012 JUKE

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT

TURNED ON

EXL-75

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXL

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT
TURNED ON

Description

INFOID:0000000007579217

The parking, license plate, tail, rear side marker lamps and each illumination are not turned ON in any condi-
tion.

Diagnosis Procedure

INFOID:0000000007579218

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to

BCS-78, "Symptom Table"

Is the combination switch normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning part.

CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

Select “TAIL & CLR REQ” of IPDM E/R data monitor item.

With operating the lighting switch, check the monitor status.

Is the item status normal?

YES

>> Replace IPDM E/R.

>> Replace BCM. Refer to

BCS-80, "Removal and Installation"

(with Intelligent Key),

BCS-141,

"Removal and Installation"

(without Intelligent Key).

Monitor item

Condition

Monitor status

TAIL & CLR REQ

Lighting switch

1ST

OFF

Revision: 2011 October

2012 JUKE

EXL-76

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON

BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON

Description

INFOID:0000000007579219

The front fog lamps are not turned ON in any condition.

Diagnosis Procedure

INFOID:0000000007579220

CHECK FUSE

Check that the following fuse is fusing.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair the applicable circuit. And then replace the fuse.

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to

BCS-78, "Symptom Table"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunctioning part.

CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

Select “FR FOG REQ” of IPDM E/R data monitor item.

With operating the front fog lamp switch, check the monitor status.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

>> Replace BCM. Refer to

BCS-80, "Removal and Installation"

(with Intelligent Key),

BCS-141,

"Removal and Installation"

(without Intelligent Key).

Unit

Location

Fuse No.

Capacity

Front fog lamp

Fuse and fusible link block

#50

15 A

Monitor item

Condition

Monitor status

FR FOG REQ

Front fog lamp switch
(With lighting switch 1ST)

OFF

Revision: 2011 October

2012 JUKE

HEADLAMP AIMING ADJUSTMENT

EXL-77

< PERIODIC MAINTENANCE >

[HALOGEN TYPE]

EXL

PERIODIC MAINTENANCE

HEADLAMP AIMING ADJUSTMENT

Description

INFOID:0000000007579221

PREPARATION BEFORE ADJUSTING

NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been

replaced.

Before performing aiming adjustment, check the following.

• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the trunk

room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.

• Wipe out dirt on the headlamp.

CAUTION:

Never use organic solvent (thinner, gasoline etc.)

• Ride alone on the driver seat.

AIMING ADJUSTMENT SCREW

JMLIA1338ZZ

Headlamp RH (UP/DOWN) adjustment screw B.

Headlamp LH (UP/DOWN) adjustment screw

: Vehicle center

Adjustment screw

Screw driver rotation

Facing direction

Headlamp RH (UP/DOWN)

Clockwise

DOWN

Counterclockwise

Revision: 2011 October

2012 JUKE

EXL-78

< PERIODIC MAINTENANCE >

[HALOGEN TYPE]

HEADLAMP AIMING ADJUSTMENT

Aiming Adjustment Procedure

INFOID:0000000007579222

Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.

Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the headlamp center and the screen.

Start the engine. Turn the headlamp (LO) ON.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.

CAUTION:

Never cover the lens surface with a tape etc. The lens is made of resin.

Measure the distance (X) between the horizontal center line of headlamp (H) and the cutoff line (A) within
the light axis measurement range (R) from the vertical center line ahead of headlamp (V).

Low beam distribution on the screen

Adjust the cutoff line height (X) with the aiming adjustment screw so as to enter in the adjustment range
(M–N) according to the horizontal center line of headlamp (H).

unit: mm (in)

Side view

Headlamp LH (UP/DOWN)

Clockwise

DOWN

Counterclockwise

Adjustment screw

Screw driver rotation

Facing direction

Light axis measurement range (R)

: 350

175 mm (13.78

6.89 in)

JSLIA0005ZZ

Horizontal center line of headlamp (H)

Highest cutoff line height (M)

Lowest cutoff line height (N)

700 (27.56) or less

4 (0.16)

30 (1.18)

701(27.60) – 800 (31.50)

4 (0.16)

30 (1.18)

801 (31.54) or more

17 (0.67)

44 (1.73)

JSLIA0006ZZ

Distance between the headlamp center and the screen (L)

: 10 m (32.8 ft)

Revision: 2011 October

2012 JUKE

FRONT FOG LAMP AIMING ADJUSTMENT

EXL-79

< PERIODIC MAINTENANCE >

[HALOGEN TYPE]

EXL

FRONT FOG LAMP AIMING ADJUSTMENT

Description

INFOID:0000000007579223

PREPARATION BEFORE ADJUSTING

NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been

replaced.

Before performing aiming adjustment, check the following.

room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.

• Wipe out dirt on the headlamp.

CAUTION:

Never use organic solvent (thinner, gasoline etc.)

• Ride alone on the driver seat.

AIMING ADJUSTMENT SCREW

• Turn the aiming adjusting screw for adjustment.

• For the position and direction of the adjusting screw, refer to the

figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.

Aiming Adjustment Procedure

INFOID:0000000007579224

Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.

Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.

Start the engine. Turn the front fog lamp ON.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.

CAUTION:

Never cover the lens surface with a tape etc. The lens is made of resin.

Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and (A) becomes 150 mm (5.91 in).

A: UP

B: DOWN

JMLIA1249ZZ

Revision: 2011 October

2012 JUKE

EXL-80

< PERIODIC MAINTENANCE >

[HALOGEN TYPE]

FRONT FOG LAMP AIMING ADJUSTMENT

Front fog lamp light distribution on the screen

JPLIA0008ZZ

: Cutoff line

: High illuminance area

: Horizontal center line of front fog lamp

: Vertical center line of front fog lamp

: Cutoff line height

Revision: 2011 October

2012 JUKE

Content .. 119 120 121 122 ..