Nissan Juke (2012 year). Service Repair Manual - part 13

 

  Index      Manuals     Nissan Juke (2012 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     11      12      13      14     ..

 

 

Nissan Juke (2012 year). Service Repair Manual - part 13

 

 

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-27

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

SELF-DIAG RESULT

Refer to 

BCS-58, "DTC Index"

.

DATA MONITOR

ANS BACK I-KEY UNLOCK

Buzzer reminder function (unlock operation) mode by door request switch can be changed to 
operation with this mode
• On: Operate
• Off: Non-operation

SHORT CRANKING OUTPUT

Starter motor can operate during the times below
• 70 msec
• 100  msec
• 200  msec

CONFIRM KEY FOB ID

It can be checked whether Intelligent Key ID code is registered or not in this mode

AUTO LOCK SET

Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes

Monitor item

Description

Monitor Item

Condition

REQ SW -DR

Indicates [On/Off] condition of door request switch (driver side)

REQ SW -AS

Indicates [On/Off] condition of door request switch (passenger side)

REQ SW -BD/TR

Indicates [On/Off] condition of back door request switch

PUSH SW

Indicates [On/Off] condition of push-button ignition switch

CLUTCH SW*

1

Indicates [On/Off] condition of clutch interlock switch

BRAKE SW 1

Indicates [On/Off]*

2

 condition of stop lamp switch power supply

BRAKE SW 2

Indicates [On/Off] condition of stop lamp switch

DETE/CANCL SW

Indicates [On/Off] condition of P position

SFT PN/N SW

Indicates [On/Off] condition of P or N position

UNLK SEN -DR

Indicates [On/Off] condition of driver door UNLOCK status

PUSH SW -IPDM

Indicates [On/Off] condition of push-button ignition switch

IGN RLY1 -F/B

Indicates [On/Off] condition of ignition relay 1

DETE SW -IPDM

Indicates [On/Off] condition of P position

SFT PN -IPDM

Indicates [On/Off] condition of P or N position

SFT P -MET

Indicates [On/Off] condition of P position

SFT N -MET

Indicates [On/Off] condition of N position

ENGINE STATE

Indicates [Stop/Stall/Crank/Run] condition of engine states

S/L LOCK-IPDM

NOTE:
This item is displayed, but cannot be monitored

S/L UNLK-IPDM

NOTE:
This item is displayed, but cannot be monitored

S/L RELAY-REQ

NOTE:
This item is displayed, but cannot be monitored

VEH SPEED 1

Display the vehicle speed signal received from combination meter by numerical value [Km/h]

VEH SPEED 2

Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]

DOOR STAT-DR

Indicates [LOCK/READY/UNLK] condition of driver side door status

DOOR STAT-AS

Indicates [LOCK/READY/UNLK] condition of passenger side door status

Revision: 2011 October

2012 JUKE

BCS-28

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

*

1

: It is displayed but does not operate on CVT models.

*

2

: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.

ACTIVE TEST

ID OK FLAG

Indicates [Set/Reset] condition of key ID

PRMT ENG STRT

Indicates [Set/Reset] condition of engine start possibility

PRMT RKE STRT

NOTE:
This item is displayed, but cannot be monitored

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored

RKE-LOCK

Indicates [On/Off] condition of LOCK signal from Intelligent Key

RKE-UNLOCK

Indicates [On/Off] condition of UNLOCK signal from Intelligent Key

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored

RKE-PANIC

Indicates [On/Off] condition of PANIC button of Intelligent Key

RKE-MODE CHG

Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing

RKE OPE COUN2

NOTE:
This item is displayed, but cannot be monitored

Monitor Item

Condition

Test item

Description

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation

INSIDE BUZZER

This test is able to check warning chime in combination meter operation
• Take Out: Take away warning chime sounds when CONSULT screen is touched
• Key: Key warning chime sounds when CONSULT screen is touched
• Knob: OFF position warning chime sounds when CONSULT screen is touched
• Off: Non-operation

INDICATOR

This test is able to check warning lamp operation
• KEY ON: “KEY” Warning lamp illuminates when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation

INT LAMP

This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation

LCD

This test is able to check meter display information
• BP N: Engine start operation indicator lamp indicate when CONSULT screen is touched
• BP I: Engine start operation indicator lamp indicate when CONSULT screen is touched
• ID NG: This item is displayed, but cannot be monitored
• ROTAT: This item is displayed, but cannot be monitored
• SFT P: Shift P warning lamp indicate when CONSULT screen is touched
• INSRT: This item is displayed, but cannot be monitored
• BATT: Key warning lamp indicator when CONSULT screen is touched
• NO KY: Key warning lamp indicator when CONSULT screen is touched
• OUTKEY: Engine start operation indicator lamp indicate when CONSULT screen is touched
• LK WN: Engine start operation indicator lamp indicate when CONSULT screen is touched

FLASHER

This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched

HORN

This test is able to check horn operation
The horn is activated after “ON” on CONSULT screen is touched

P RANGE

This test is able to check CVT shift selector power supply
• On: Operate
• Off: Non-operation

Revision: 2011 October

2012 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-29

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

COMB SW

COMB SW : CONSULT Function (BCM - COMB SW)

INFOID:0000000007576654

DATA MONITOR

BCM

BCM : CONSULT Function (BCM - BCM)

INFOID:0000000007576655

WORK SUPPORT

IMMU

ENGINE SW ILLUMI

This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched

PUSH SWITCH INDICATOR

This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT screen is touched

BATTERY SAVER

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT screen is touched.

TRUNK/BACK DOOR

This test is able to check back door opener actuator open operation.
This actuator opens when “Open” on CONSULT screen is touched.

Test item

Description

Monitor item [UNIT]

Description

FR WIPER HI
[Off/On]

Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination 
switch reading function.

FR WIPER LOW
[Off/On]

Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination 
switch reading function.

FR WASHER SW
[Off/On]

Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination 
switch reading function.

FR WIPER INT
[Off/On]

Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination 
switch reading function.

INT VOLUME
[1 - 7]

Displays the status of wiper volume dial position judged by BCM with the combination switch reading function.

TURN SIGNAL R
[Off/On]

Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch 
reading function.

TURN SIGNAL L
[Off/On]

Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch 
reading function.

TAIL LAMP SW
[Off/On]

Displays the status of the TAIL LAMP switch in combination switch judged by BCM with the combination 
switch reading function.

HI BEAM SW
[Off/On]

Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch 
reading function.

HEAD LAMP SW 1
[Off/On]

Displays the status of the HEADLAMP 1 switch in combination switch judged by BCM with the combination 
switch reading function.

HEAD LAMP SW 2
[Off/On]

Displays the status of the HEADLAMP 2 switch in combination switch judged by BCM with the combination 
switch reading function.

PASSING SW
[Off/On]

Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch 
reading function.

AUTO LIGHT SW
[Off/On]

Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination 
switch reading function.

FR FOG SW
[Off/On]

Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch 
reading function.

Item

Description

RESET SETTING VALUE

Return a value set with Work Support of each system to a default value in factory shipment.

Revision: 2011 October

2012 JUKE

BCS-30

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

IMMU : CONSULT Function (BCM - IMMU)

INFOID:0000000007829419

WORK SUPPORT

DATA MONITOR

ACTIVE TEST

BATTERY SAVER

BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)

INFOID:0000000007829431

WORK SUPPORT

*:Factory setting

DATA MONITOR

Service item

Description

CONFIRM DONGLE ID

It is possible to check that dongle unit is applied to the vehicle.

Monitor item 

Content

CONFRM ID ALL

Indicates [YET] at all time.
Switches to [DONE] when a registered Intelligent Key backside is contacted to push-button igni-
tion switch.

CONFIRM ID4

CONFIRM ID3

CONFIRM ID2

CONFIRM ID1

NOT REGISTERED

Indicates [ID OK] when key ID that is registered is received or is not yet received.
Indicates [ID NG] when key ID that is not registered is received.

TP 4

Indicates the number of IDs that are registered.

TP 3

TP 2

TP 1

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch.

Test item

Description

THEFT IND

This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen is touched.

Service item

Setting item

Setting

ROOM LAMP TIMER SET

MODE 1

30 min.

Sets the interior room lamp battery saver timer operating 
time.

MODE 2

60 min.

MODE 3

*

15 min.

BATTERY SAVER SET

On

*

With the exterior lamp battery saver function

Off

Without the exterior lamp battery saver function

ROOM LAMP BAT SAV SET

On

*

With the interior room lamp battery saver function

Off

Without the interior room lamp battery saver function

Revision: 2011 October

2012 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-31

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

ACTIVE TEST

*: Each lamp switch is in ON position.

TRUNK

TRUNK : CONSULT Function (BCM - TRUNK)

INFOID:0000000007829417

DATA MONITOR

Monitor item

[Unit]

Description

REQ SW-DR
[On/Off]

The switch status input from request switch (driver side)

REQ SW-AS
[On/Off]

The switch status input from request switch (passenger side)

REQ SW-RR
[On/Off]

NOTE:
The item is indicated, but not monitored.

REQ SW-RL
[On/Off]

PUSH SW
[On/Off]

Push switch status received from Intelligent Key unit by CAN communication

UNLK SEN -DR
[On/Off]

NOTE:
The item is indicated, but not monitored

DOOR SW-DR
[On/Off]

The switch status input from front door switch (driver side)

DOOR SW-AS
[On/Off]

The switch status input from front door switch (passenger side)

DOOR SW-RR
[On/Off]

The switch status input from rear door switch RH

DOOR SW- RL
[On/Off]

The switch status input from rear door switch LH

DOOR SW- BK
[On/Off]

The switch status input from back door switch

CDL LOCK SW
[On/Off]

Lock switch status input from door lock and unlock switch

CDL UNLOCK SW
[On/Off]

Unlock switch status input from door lock and unlock switch

TRNK/HAT MNTR
[On/Off]

NOTE:
The item is indicated, but not monitored

KEY CYL LK-SW
[On/Off]

Lock switch status received from key cylinder switch

KEY CYL UN-SW
[On/Off]

Unlock switch status received from key cylinder switch

RKE-LOCK
[On/Off]

Lock signal status received from remote keyless entry receiver

RKE-UNLOCK
[On/Off]

Unlock signal status received from remote keyless entry receiver

Test item

Operation

Description

BATTERY SAVER

Off

Cuts the interior room lamp power supply to turn interior room lamps OFF.

On

Outputs the interior room lamp power supply to turn interior room lamps ON.*

Revision: 2011 October

2012 JUKE

BCS-32

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

THEFT ALM

THEFT ALM : CONSULT Function (BCM - THEFT)

INFOID:0000000007829418

WORK SUPPORT

DATA MONITOR

Monitor Item

Contents

PUSH SW

Indicates [On/Off] condition of push switch

UNLK SEN -DR

Indicates [On/Off] condition of unlock sensor

VEH SPEED 1

Indicates [Km/h] condition of vehicle speed signal from combination meter

TR/BD OPEN SW

Indicates [ON/OFF] condition of back door opener switch.

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored

Service Item

Description

SECURITY ALARM SET

This mode is able to confirm and change security alarm ON-OFF setting.

THEFT ALM TRG

The switch which triggered vehicle security alarm is recorded.
This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT screen.

Monitored Item

Description

REQ SW -DR

Indicates [ON/OFF] condition of door request switch (driver side).

REQ SW -AS

Indicates [ON/OFF] condition of door request switch (passenger side).

REQ SW -RR

NOTE:
This is displayed even when it is not equipped.

REQ SW -RL

NOTE:
This is displayed even when it is not equipped.

REQ SW -BD/TR

Indicates [ON/OFF] condition of back door request switch.

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch

UNLK SEN -DR

Indicates [ON/OFF] condition of driver door UNLOCK status.

DOOR SW-DR

Indicates [ON/OFF] condition of front door switch (driver side).

DOOR SW-AS

Indicates [ON/OFF] condition of front door switch (passenger side).

DOOR SW-RR

Indicates [ON/OFF] condition of rear door switch RH.

DOOR SW-RL

Indicates [ON/OFF] condition of rear door switch LH.

DOOR SW-BK

Indicates [ON/OFF] condition of back door switch.

CDL LOCK SW

Indicates [ON/OFF] condition of lock signal from door lock/unlock switch.

CDL UNLOCK SW

Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch.

KEY CYL LK-SW

Indicates [ON/OFF] condition of lock signal from door key cylinder.

KEY CYL UN-SW

Indicates [ON/OFF] condition of unlock signal from door key cylinder.

TR/BD OPEN SW

Indicates [ON/OFF] condition of back door opener switch.

TRNK/HAT MNTR

NOTE:
This is displayed even when it is not equipped.

RKE-LOCK

Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.

RKE-UNLOCK

Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.

RKE-TR/BD

NOTE:
This is displayed even when it is not equipped.

Revision: 2011 October

2012 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-33

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

ACTIVE TEST

RETAIND PWR

RETAIND PWR : CONSULT Function (BCM - RETAINED PWR)

INFOID:0000000007829420

DATA MONITOR

SIGNAL BUFFER

SIGNAL BUFFER : CONSULT Function (BCM - SIGNAL BUFFER)

INFOID:0000000007576661

DATA MONITOR

ACTIVE TEST

AIR PRESSURE MONITOR

AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONI-
TOR)

INFOID:0000000007829440

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

SELF DIAGNOSTIC RESULT

Refer to 

BCS-58, "DTC Index"

.

DATA MONITOR MODE

Test Item

Description

THEFT IND

This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen is touched.

VEHICLE SECURITY HORN

This test is able to check horns operation.
Horns are activated for 0.5 seconds after “ON” on CONSULT screen is touched.

HEADLAMP(HI)

This test is able to check headlamp operation.
Headlamps are activated for 0.5 seconds after “ON” on CONSULT screen is touched.

FLASHER

This test is able to check hazard warning lamp operation.
Hazard warning lamps are activated after “ON” on CONSULT screen is touched.

Monitor Item

Description

DOOR SW-DR

Indicates [ON/OFF] condition of driver side door switch.

DOOR SW-AS

Indicates [ON/OFF] condition of passenger side door switch.

Monitor item [UNIT]

Description

PUSH SW
[Off/On]

Displays the status of the push-button ignition switch (push switch) judged by BCM.

Test item

Opera-

tion

Description

OIL PRESSURE SW

Off

NOTE:
This item is indicated, but not tested.

On

Diagnosis mode

Function Description

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Work Support

Components can be quickly and accurately adjusted.

Revision: 2011 October

2012 JUKE

BCS-34

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

ACTIVE TEST MODE

NOTE:
After completing the work below, perform an active test.
1.

Check ID registration state and perform self-diagnosis.

2.

Erase the self-diagnosis result history.

WORK SUPPORT

Monitor item (Unit)

Remarks

AIR PRESS FL
(kPa, kg/cm2 or Psi)

Tire pressure

AIR PRESS FR
(kPa, kg/cm2 or Psi)

AIR PRESS RR
(kPa, kg/cm2 or Psi)

AIR PRESS RL
(kPa, kg/cm2 or Psi)

ID REGST FL1
(Yet, Done)

Registration ID

ID REGST FR1
(Yet, Done)

ID REGST RR1
(Yet, Done)

ID REGST RL1
(Yet, Done)

WARNING LAMP
 (On/Off)

Low tire pressure warning lamp

BUZZER
 (On/Off)

NOTE:
This item is displayed, but cannot be use this item.

Item

Description

WARNING LAMP

Low tire pressure warning lamp can be turned ON arbitrarily.

ID REGIST WARNING

NOTE:
Displayed but not used in TPMS.

RUN FLAT TIRE W/L

NOTE:
Displayed but not used in TPMS.

RUN FLAT/T WARN BUZZER

NOTE:
Displayed but not used in TPMS.

FLASHER

Turn signal lamps can be turned ON arbitrarily.

HORN

This test is able to check to check that the horn sounds.

Item

Description

ID READ

Registered tire pressure sensor ID can be displayed.

ID REGIST

Tire pressure sensor ID can be registered.

Revision: 2011 October

2012 JUKE

BCS

BCM

BCS-35

< ECU DIAGNOSIS INFORMATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

ECU DIAGNOSIS INFORMATION

BCM

Reference Value

INFOID:0000000007576663

VALUES ON THE DIAGNOSIS TOOL

CONSULT MONITOR ITEM

Monitor Item

Condition

Value/Status

FR WIPER HI

Other than front wiper switch HI

Off

Front wiper switch HI

On

FR WIPER LOW

Other than front wiper switch LO

Off

Front wiper switch LO

On

FR WASHER SW

Front washer switch OFF

Off

Front washer switch ON

On

FR WIPER INT

Other than front wiper switch INT

Off

Front wiper switch INT

On

FR WIPER STOP

Front wiper is not in STOP position

Off

Front wiper is in STOP position

On

INT VOLUME

Wiper intermittent dial is in a dial position 1 - 7

Wiper intermittent dial 

position

RR WIPER ON

Other than rear wiper switch ON

Off

Rear wiper switch ON

On

RR WIPER INT

Other than rear wiper switch INT

Off

Rear wiper switch INT

On

RR WASHER SW

Rear washer switch OFF

Off

Rear washer switch ON

On

RR WIPER STOP

Rear wiper is in STOP position

Off

Rear wiper is not in STOP position

On

TURN SIGNAL R

Other than turn signal switch RH

Off

Turn signal switch RH

On

TURN SIGNAL L

Other than turn signal switch LH

Off

Turn signal switch LH

On

TAIL LAMP SW

Other than lighting switch 1ST and 2ND

Off

Lighting switch 1ST or 2ND

On

HI BEAM SW

Other than lighting switch HI

Off

Lighting switch HI

On

HEAD LAMP SW 1

Other than lighting switch 2ND

Off

Lighting switch 2ND

On

HEAD LAMP SW 2

Other than lighting switch 2ND

Off

Lighting switch 2ND

On

PASSING SW

Other than lighting switch PASS

Off

Lighting switch PASS

On

AUTO LIGHT SW

Other than lighting switch AUTO

Off

Lighting switch AUTO

On

FR FOG SW

Front fog lamp switch OFF

Off

Front fog lamp switch ON

On

Revision: 2011 October

2012 JUKE

BCS-36

< ECU DIAGNOSIS INFORMATION >

[WITH INTELLIGENT KEY SYSTEM]

BCM

DOOR SW-DR

Driver door closed

Off

Driver door opened

On

DOOR SW-AS

Passenger door closed

Off

Passenger door opened

On

DOOR SW-RR

Rear RH door closed

Off

Rear RH door opened

On

DOOR SW-RL

Rear LH door closed

Off

Rear LH door opened

On

DOOR SW-BK

Back door closed

Off

Back door opened

On

CDL LOCK SW

Other than power door lock switch LOCK

Off

Power door lock switch LOCK

On

CDL UNLOCK SW

Other than power door lock switch UNLOCK

Off

Power door lock switch UNLOCK

On

KEY CYL LK-SW

Other than driver door key cylinder LOCK position

Off

Driver door key cylinder LOCK position

On

KEY CYL UN-SW

Other than driver door key cylinder UNLOCK position

Off

Driver door key cylinder UNLOCK position

On

HAZARD SW

Hazard switch is OFF

Off

Hazard switch is ON

On

REAR DEF SW

Rear window defogger switch OFF

Off

Rear window defogger switch ON

On

TR/BD OPEN SW

Back door opener switch OFF

Off

While the back door opener switch is turned ON

On

TRNK/HAT MNTR

NOTE:
The item is indicated, but not monitored. 

Off

FAN ON SIG

Blower fan OFF

Off

Blower fan ON

On

AIR COND SW

Air conditioner OFF (A/C switch indicator OFF)

Off

Air conditioner ON (A/C switch indicator ON)

On

RKE-LOCK

LOCK button of the key is not pressed

Off

LOCK button of the key is pressed

On

RKE-UNLOCK

UNLOCK button of the key is not pressed

Off

UNLOCK button of the key is pressed

On

RKE-TR/BD

NOTE:
The item is indicated, but not monitored. 

Off

RKE-PANIC

PANIC button of the key is not pressed

Off

PANIC button of the key is pressed

On

RKE-MODE CHG

LOCK/UNLOCK button of the key is not pressed and held simultaneously

Off

LOCK/UNLOCK button of the key is pressed and held simultaneously

On

OPTI SEN (DTCT)

Bright outside of the vehicle

Close to 5 V

Dark outside of the vehicle

Close to 0 V

OPTI SEN (FILT)

Bright outside of the vehicle (Lighting switch AUTO)

Close to 5 V

Dark outside of the vehicle (Lighting switch AUTO)

Close to 1.50 V

Monitor Item

Condition

Value/Status

Revision: 2011 October

2012 JUKE

BCS

BCM

BCS-37

< ECU DIAGNOSIS INFORMATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

OPTICAL SENSOR

NOTE:
The item is indicated, but not monitored. 

Off

RAIN SENSOR

NOTE:
The item is indicated, but not monitored. 

Off

REQ SW -DR

Driver door request switch is not pressed

Off

Driver door request switch is pressed

On

REQ SW -AS

Passenger door request switch is not pressed

Off

Passenger door request switch is pressed

On

REQ SW -RR

NOTE:
The item is indicated, but not monitored. 

Off

REQ SW -RL

NOTE:
The item is indicated, but not monitored. 

Off

REQ SW -BD/TR

Back door request switch is not pressed

Off

Back door request switch is pressed

On

PUSH SW

Push-button ignition switch (push switch) is not pressed

Off

Push-button ignition switch (push switch) is pressed

On

CLUCH SW

The clutch pedal is not depressed. 

Off

The clutch pedal is depressed

On

BRAKE SW 1

The brake pedal is not depressed

Off

The brake pedal is depressed

On

BRAKE SW 2

The brake pedal is depressed when No. 38 fuse is blown

Off

The brake pedal is not depressed when No. 38 fuse is blown, or No. 38 
fuse is normal

On

DETE/CANCL SW
NOTE:
For M/T models this item is not 
used.

Selector lever in P position

Release selector button

Off

Push selector button

On

Selector lever in any position other than P

SFT PN/N SW

• Selector lever in any position other than P and N (CVT models)
• Control lever in any position other than neutral (M/T models)

Off

• Selector lever in P or N position (CVT models)
• Control lever in neutral position (M/T models)

On

S/L -LOCK

NOTE:
The item is indicated, but not monitored. 

Off

S/L -UNLOCK

NOTE:
The item is indicated, but not monitored. 

Off

S/L RELAY-F/B

NOTE:
The item is indicated, but not monitored. 

Off

UNLK SEN -DR

Driver door is locked

Off

Driver door is unlocked

On

PUSH SW -IPDM

Push-button ignition switch (push-switch) is not pressed

Off

Push-button ignition switch (push-switch) is pressed

On

IGN RLY1 -F/B

Ignition switch in OFF or ACC position

Off

Ignition switch in ON position

On

DETE SW -IPDM
NOTE:
For M/T models this item is not 
used.

Selector lever in any position other than P

Off

Selector lever in P position

Push selector button

Release selector button

On

Monitor Item

Condition

Value/Status

Revision: 2011 October

2012 JUKE

BCS-38

< ECU DIAGNOSIS INFORMATION >

[WITH INTELLIGENT KEY SYSTEM]

BCM

SFT PN -IPDM
NOTE:
For M/T models this item is not 
used.

Selector lever in any position other than P and N

Off

Selector lever in P or N position

On

SFT P -MET
NOTE:
For M/T models this item is not 
used.

Selector lever in any position other than P

Off

Selector lever in P position

On

SFT N -MET
NOTE:
For M/T models this item is not 
used.

Selector lever in any position other than N

Off

Selector lever in N position

On

ENGINE STATE

Engine stopped

Stop

While the engine stalls

Stall

At engine cranking

Crank

Engine running

Run

S/L LOCK-IPDM

NOTE:
The item is indicated, but not monitored. 

Off

S/L UNLK-IPDM

NOTE:
The item is indicated, but not monitored. 

Off

S/L RELAY-REQ

NOTE:
The item is indicated, but not monitored. 

Off

VEH SPEED 1

While driving

Equivalent to speed-

ometer reading

VEH SPEED 2

While driving

Equivalent to speed-

ometer reading

DOOR STAT-DR

Driver door is locked

LOCK

Wait with selective unlock operation (60 seconds)

READY

Driver door is unlocked

UNLOCK

DOOR STAT-AS

Passenger door is locked

LOCK

Wait with selective unlock operation (60 seconds)

READY

Passenger door is unlocked

UNLOCK

ID OK FLAG

Driver side door is open after ignition switch is turned OFF
(Shift position is in the P position)

Reset

Ignition switch ON

Set

PRMT ENG STRT

The engine start is prohibited

Reset

The engine start is permitted

Set

PRMT RKE STRT

NOTE:
The item is indicated, but not monitored. 

Reset

RKE OPE COUN1

During the operation of the key

Operation frequency 

of the key

RKE OPE COUN2

NOTE:
The item is indicated, but not monitored. 

CONFRM ID ALL

The key ID that the key slot receives is not recognized by any key ID reg-
istered to BCM.

Yet

The key ID that the key slot receives is recognized by any key ID regis-
tered to BCM.

Done

CONFIRM ID4

The key ID that the key slot receives is not recognized by the fourth key ID 
registered to BCM.

Yet

The key ID that the key slot receives is recognized by the fourth key ID reg-
istered to BCM.

Done

Monitor Item

Condition

Value/Status

Revision: 2011 October

2012 JUKE

BCS

BCM

BCS-39

< ECU DIAGNOSIS INFORMATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

CONFIRM ID3

The key ID that the key slot receives is not recognized by the third key ID 
registered to BCM.

Yet

The key ID that the key slot receives is recognized by the third key ID reg-
istered to BCM.

Done

CONFIRM ID2

The key ID that the key slot receives is not recognized by the second key 
ID registered to BCM.

Yet

The key ID that the key slot receives is recognized by the second key ID 
registered to BCM.

Done

CONFIRM ID1

The key ID that the key slot receives is not recognized by the first key ID 
registered to BCM.

Yet

The key ID that the key slot receives is recognized by the first key ID reg-
istered to BCM.

Done

NOT REGISTERED

BCM detects registered key ID, or BCM does not detect key ID. 

ID OK

BCM detects non-registration key ID.

ID NG

TP 4

The ID of fourth key is not registered to BCM

Yet

The ID of fourth key is registered to BCM

Done

TP 3

The ID of third key is not registered to BCM

Yet

The ID of third key is registered to BCM

Done

TP 2

The ID of second key is not registered to BCM

Yet

The ID of second key is registered to BCM

Done

TP 1

The ID of first key is not registered to BCM

Yet

The ID of first key is registered to BCM

Done

AIR PRESS FL

Ignition switch ON (Only when the signal from the transmitter is received)

Air pressure of front 

LH tire

AIR PRESS FR

Ignition switch ON (Only when the signal from the transmitter is received)

Air pressure of front 

RH tire

AIR PRESS RR

Ignition switch ON (Only when the signal from the transmitter is received)

Air pressure of rear 

RH tire

AIR PRESS RL

Ignition switch ON (Only when the signal from the transmitter is received)

Air pressure of rear 

LH tire

ID REGST FL1

ID of front LH tire transmitter is registered

Done

ID of front LH tire transmitter is not registered

Yet

ID REGST FR1

ID of front RH tire transmitter is registered

Done

ID of front RH tire transmitter is not registered

Yet

ID REGST RR1

ID of rear RH tire transmitter is registered

Done

ID of rear RH tire transmitter is not registered

Yet

ID REGST RL1

ID of rear LH tire transmitter is registered

Done

ID of rear LH tire transmitter is not registered

Yet

WARNING LAMP

Tire pressure indicator OFF

Off

Tire pressure indicator ON

On

BUZZER

Tire pressure warning alarm is not sounding

Off

Tire pressure warning alarm is sounding

On

Monitor Item

Condition

Value/Status

Revision: 2011 October

2012 JUKE

BCS-40

< ECU DIAGNOSIS INFORMATION >

[WITH INTELLIGENT KEY SYSTEM]

BCM

TERMINAL LAYOUT

PHYSICAL VALUES

JMMIA0323ZZ

Revision: 2011 October

2012 JUKE

BCS

BCM

BCS-41

< ECU DIAGNOSIS INFORMATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

Terminal No.

(Wire color)

Description

Condition

Value

(Approx.)

Signal name

Input/ 

Output

+

2

(L)

Ground

Combination switch 
INPUT 5

Input

Combination 
switch
(Wiper intermit-
tent dial 4)

All switches OFF

0 V

Turn signal switch RH

1.0 V

Lighting switch HI

Lighting switch 1ST

Lighting switch 2ND

2.0 V

3

(GR)

Ground

Combination switch 
INPUT 4

Input

Combination 
switch
(Wiper intermit-
tent dial 4)

All switches OFF

0 V

Turn signal switch LH

1.0 V

Lighting switch PASS

Lighting switch 2ND

Front fog lamp switch ON

0.8 V

4

(BR)

Ground

Combination switch 
INPUT 3

Input

Combination 
switch
(Wiper intermit-
tent dial 4)

All switches OFF

0 V

Front wiper switch LO

1.0 V

Front wiper switch MIST

Front wiper switch INT

Lighting switch AUTO

PKIB4958J

JPMIA0342JP

PKIB4958J

PKIB4956J

PKIB4958J

Revision: 2011 October

2012 JUKE

BCS-42

< ECU DIAGNOSIS INFORMATION >

[WITH INTELLIGENT KEY SYSTEM]

BCM

5

(G)

Ground

Combination switch 
INPUT 2

Input

Combination 
switch

All switches OFF
(Wiper intermittent dial 4)

0 V

Front washer switch ON
(Wiper intermittent dial 4)

1.0 V

Rear washer switch ON
(Wiper intermittent dial 4)

Any of the condition below 
with all switches OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 5
• Wiper intermittent dial 6

Rear wiper switch ON
(Wiper intermittent dial 4)

0.8 V

6

(W)

Ground

Combination switch 
INPUT 1

Input

Combination 
switch

All switches OFF
(Wiper intermittent dial 4)

0 V

Front wiper switch HI
(Wiper intermittent dial 4)

1.0 V

Rear wiper switch INT
(Wiper intermittent dial 4)

Wiper intermittent dial 3
(All switches OFF)

Any of the condition below 
with all switches OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2

1.9 V

Any of the condition below 
with all switches OFF
• Wiper intermittent dial 6
• Wiper intermittent dial 7

0.8 V

Terminal No.

(Wire color)

Description

Condition

Value

(Approx.)

Signal name

Input/ 

Output

+

PKIB4958J

PKIB4956J

PKIB4958J

PKIB4952J

PKIB4956J

Revision: 2011 October

2012 JUKE

 

 

 

 

 

 

 

Content      ..     11      12      13      14     ..