Nissan Juke (2016 year). Service Repair Manual - part 695

REAR WIPER MOTOR

WW-59

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

REAR WIPER MOTOR

Exploded View

INFOID:0000000012197091

Removal and Installation

INFOID:0000000012197092

REMOVAL

1. Remove rear wiper arm. Refer to 

WW-57, "Removal and Installation"

.

2. Remove back door lower finisher. Refer to 

INT-39, "BACK DOOR SIDE FINISHER : Removal and Installa-

tion"

.

3. Disconnect rear wiper motor connector.
4. Remove rear wiper motor mounting bolts.
5. Remove rear wiper motor from the vehicle.
6. Remove the pivot seal.

INSTALLATION

Install in the reverse order of removal.

1.

Rear wiper motor

2.

Rear wiper blade

3.

Rear wiper arm

4.

Rear wiper arm cover

5.

Rear wiper pivot seal

A

: Canada models only

: Pawl

: N·m (kg-m, in-lb)

: N·m (kg-m, ft-lb)

JMLIA1503GB

Revision: November 2015

2016 JUKE

WW-60

< REMOVAL AND INSTALLATION >

REAR WASHER NOZZLE AND TUBE

REAR WASHER NOZZLE AND TUBE

Hydraulic Layout

INFOID:0000000012197093

Removal and Installation

INFOID:0000000012197094

REMOVAL

1. Remove luggage side upper finisher RH. Refer to 

INT-36, "LUGGAGE SIDE UPPER FINISHER :

Removal and Installation"

.

2. Disconnect rear washer tube (1) fixing clip and then remove rear

washer tube joint (2) from rear washer tube.

1.

Rear washer nozzle

2.

Plug

3.

Rear washer tube

4.

Joint

5.

Second washer tube

6.

Back door seal rubber

7.

Front washer tube

: Clip

: Pawl

JMLIA1221ZZ

: Clip

JMLIA1222ZZ

Revision: November 2015

2016 JUKE

REAR WASHER NOZZLE AND TUBE

WW-61

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

3. Fully open back door.
4. Remove back door seal rubber (2), and then remove rear

washer tube (3) from back door seal rubber.

5. Remove plug (1).

6. Disengage rear washer nozzle (1) fixing pawl with a flat-bladed

screwdriver (A) and remove the rear washer nozzle.

CAUTION:

Wrap the flat-bladed screwdriver into a protective tape (B)

to protect the part from damage.

7. Remove rear washer nozzle from the rear washer tube.

INSTALLATION

Install in the reverse order of removal.

Inspection and Adjustment

INFOID:0000000012197095

INSPECTION

Washer Nozzle Inspection

Check that air can pass through the hose by blowing forward (toward

the nozzle), and check that air cannot pass through by sucking.

ADJUSTMENT

Washer Nozzle Spray Position adjustment

JMLIA1223ZZ

JMLIA1224ZZ

JMLIA1171ZZ

Revision: November 2015

2016 JUKE

WW-62

< REMOVAL AND INSTALLATION >

REAR WASHER NOZZLE AND TUBE

Adjust spray positions to match the positions shown in the figure.

Unit: mm (in)

Insert a needle or similar object (A) into the spray opening (1) and

move up/down and left/right to adjust the spray position.

NOTE:

If wax or dust gets into the spray opening of rear washer nozzle (2),

remove wax or dust with a needle or small pin.

1.

Rear washer nozzle

2.

Black print frame line

L: Length

H : Height

φ

: Spray area

122.8 (4.83)

32.8 (1.29)

30 (1.18)

JMLIA1225ZZ

JMLIA1172ZZ

Revision: November 2015

2016 JUKE