Nissan Juke (2016 year). Service Repair Manual - part 681

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     679      680      681      682     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 681

 

 

WCS-40

< DTC/CIRCUIT DIAGNOSIS >

METER BUZZER CIRCUIT

METER BUZZER CIRCUIT

Component Function Check

INFOID:0000000012201483

1.

CHECK OPERATION OF METER BUZZER

1. Select “BUZZER” of “BCM” on CONSULT.

2. Perform “LIGHT WARN ALM” of “Active Test”.
Does meter buzzer beep?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK COMBINATION METER INPUT SIGNAL

Select the “Data Monitor” for the “METER/M&A” and check the “BUZZER” monitor value.

Is the inspection result normal?

YES

>> Replace combination meter.

NO

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

Diagnosis Procedure

INFOID:0000000012201484

1.

CHECK POWER SUPPLY OF COMBINATION METER

Check power supply of combination meter. Refer to 

MWI-53, "COMBINATION METER : Diagnosis Proce-

dure"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair power supply circuit of combination meter.

BUZZER
Under the condition of buzzer input

: On

Except above

: Off

Revision: November 2015

2016 JUKE

WCS

SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT

WCS-41

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT

Component Function Check

INFOID:0000000012201485

1.

CHECK COMBINATION METER INPUT SIGNAL

Select the “Data Monitor” for the “METER/M&A” and check the “BUCKLE SW” monitor value.

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012201486

1.

CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect combination meter connector and seat belt buckle switch (driver side) connector.

3. Check continuity between combination meter harness connector and seat belt buckle switch (driver side)

harness connector.

4. Check harness continuity between combination meter harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair harness or connector.

2.

CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) GROUND CIRCUIT

Check harness continuity between seat belt buckle switch (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair harness or connector.

Component Inspection

INFOID:0000000012201487

1.

CHECK SEAT BELT BUCKLE SWITCH UNIT

1. Turn ignition switch OFF.

2. Disconnect the seat belt buckle switch (driver side) connector.

3. Check continuity between terminals.

BUCKLE SW
When driver seat belt is fastened

: Off

When driver seat belt is unfastened

: On

Combination meter

Seat belt buckle switch (driver side)

Continuity

Connector

Terminal

Connector

Terminal

M34

9

B50

1

Existed

Combination meter

Ground

Continuity

Connector

Terminal

M34

9

Not existed

Seat belt buckle switch (driver side)

Ground

Continuity

Connector

Terminal

B50

2

Existed

Revision: November 2015

2016 JUKE

WCS-42

< DTC/CIRCUIT DIAGNOSIS >

SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace the seat belt buckle (driver side). Refer to 

SB-9, "SEAT BELT BUCKLE : Removal and

Installation"

.

Terminal

Condition

Continuity

1

2

When driver seat belt is fastened

Not existed

When driver seat belt is unfastened

Existed

Revision: November 2015

2016 JUKE

WCS

PARKING BRAKE SWITCH SIGNAL CIRCUIT

WCS-43

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

PARKING BRAKE SWITCH SIGNAL CIRCUIT

Diagnosis Procedure

INFOID:0000000012201488

1.

CHECK COMBINATION METER INPUT SIGNAL

1. Turn ignition switch ON.

2. Check the voltage between combination meter harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect combination meter connector and parking brake switch connector. 

3. Check continuity between combination meter harness connector and parking brake switch harness con-

nector.

4. Check continuity between combination meter harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair harness or connector.

Component Inspection

INFOID:0000000012201489

1.

CHECK PARKING BRAKE SWITCH

Check parking brake switch. Refer to 

BRC-132, "Component Inspection"

.

Is the inspection result normal? 

YES

>> INSPECTION END.

NO

>> Replace parking brake switch. Refer to 

PB-6, "Exploded View"

.

(+)

(

)

Condition

Voltage

(Approx.)

Combination meter

Ground

Connector

Terminal

M34

10

Ignition 
switch ON

When parking brake is applied

0 V

When parking brake is released

12 V

Terminals

Continuity

Combination meter

Parking brake switch

Connector

Terminal

Connector

Terminal

M34

10

M31

1

Existed

Terminals

Continuity

Combination meter

Ground

Connector

Terminal

M34

10

Not existed

Revision: November 2015

2016 JUKE

WCS-44

< SYMPTOM DIAGNOSIS >

THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR 

DOES NOT SOUND

SYMPTOM DIAGNOSIS

THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND

Description

INFOID:0000000012201490

• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is

released.

• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking

brake applied.

Diagnosis Procedure

INFOID:0000000012201491

1.

CHECK PARKING BRAKE WARNING LAMP

1. Start the engine.

2. Check the operation of the brake warning lamp by operating the parking brake.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-64, "Removal and Installation"

NO

>> GO TO 2.

2.

CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT

Perform check for the parking brake switch signal circuit. Refer to 

WCS-43, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair harness or connector.

3.

CHECK PARKING BRAKE SWITCH

Perform a unit check for the parking brake switch. Refer to 

WCS-43, "Component Inspection"

.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-64, "Removal and Installation"

NO

>> Replace parking brake switch. Refer to 

PB-6, "Exploded View"

.

When parking brake is applied

: ON

When parking brake is released

: OFF

Revision: November 2015

2016 JUKE

WCS

THE LIGHT REMINDER WARNING DOES NOT SOUND

WCS-45

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

THE LIGHT REMINDER WARNING DOES NOT SOUND

Description

INFOID:0000000012201492

Light reminder warning chime does not sound even though headlamp is illuminated.

Diagnosis Procedure

INFOID:0000000012201493

1.

CHECK COMBINATION SWITCH (LIGHTING SWITCH) OPERATION

Check that the headlamps operate normally by operating the combination switch (lighting switch).
Do they operate normally?

YES

>> GO TO 2.

NO

>> Refer to 

EXL-79, "Symptom Table"

 (XENON TYPE) or 

EXL-190, "Symptom Table"

 (HALOGEN

TYPE).

2.

CHECK DRIVER SIDE DOOR SWITCH SIGNAL CIRCUIT

Perform the check for the driver side door switch signal circuit. Refer to 

DLK-77, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair harness or connector.

3.

CHECK DRIVER SIDE DOOR SWITCH

Perform a unit check for the driver side door switch. Refer to 

DLK-78, "Component Inspection"

.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> Replace driver side door switch. Refer to 

DLK-169, "Removal and Installation"

.

Revision: November 2015

2016 JUKE

WCS-46

< SYMPTOM DIAGNOSIS >

THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT SOUND

THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT
SOUND

Description

INFOID:0000000012201494

• Seat belt warning does not sound.

• Seat belt warning sounds continuously.

Diagnosis Procedure

INFOID:0000000012201495

1.

CHECK SEAT BELT WARNING LAMP

1. Turn ignition switch ON.

2. Check the operation of the seat belt warning lamp in the combination meter.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK BCM OUTPUT SIGNAL

Check if the seat belt warning chime is activated by performing BCM active test. Refer to 

WCS-19, "BUZZER :

CONSULT Function (BCM - BUZZER)"

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 3.

3.

CHECK COMBINATION METER INPUT SIGNAL

Check if buzzer switches to proper condition (On/Off) on data monitor of combination meter. Refer to 

MWI-22,

"CONSULT Function"

.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-64, "Removal and Installation"

.

NO

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

4.

CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) CIRCUIT

Perform the check for the seat belt buckle switch (driver side) circuit. Refer to 

WCS-41,

"Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair harness or connector.

5.

CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)

Perform a unit check for the seat belt buckle switch (driver side). Refer to 

WCS-41, "Component Inspection"

.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-64, "Removal and Installation"

.

NO

>> Replace seat belt buckle (driver side). Refer to 

SB-9, "SEAT BELT BUCKLE : Removal and Instal-

lation"

.

Seat belt fastened

: OFF

Seat belt not fastened

: ON

Buzzer active condition

: On

Buzzer non-active condition

: Off

Revision: November 2015

2016 JUKE

WT-1

SUSPENSION

C

D

F

G

H

I

J

K

L

M

SECTION 

WT

A

B

WT

N

O

P

CONTENTS

ROAD WHEELS & TIRES

PRECAUTION ...............................................

3

PRECAUTIONS ...................................................

3

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .................................................................
..

3

Precautions for Removing Battery Terminal  .............

3

Service Notice and Precautions for TPMS ................

3

Service Notice and Precautions for Road Wheel ......

4

PREPARATION ............................................

5

PREPARATION ...................................................

5

Special Service Tool  .................................................

5

Commercial Service Tool  ..........................................

5

SYSTEM DESCRIPTION  ..............................

6

COMPONENT PARTS  ........................................

6

Component Parts Location ........................................

6

Component Description .............................................

6

BCM ..........................................................................

7

Tire Pressure Sensor  ................................................

7

Tire Pressure Receiver  .............................................

7

Information Display  ...................................................

7

SYSTEM ..............................................................

8

System Description  ...................................................

8

DIAGNOSIS SYSTEM (BCM)  .............................

9

COMMON ITEM ...........................................................

9

COMMON ITEM : CONSULT Function (BCM - 
COMMON ITEM) .....................................................
..

9

AIR PRESSURE MONITOR  ......................................

10

AIR PRESSURE MONITOR : CONSULT Function 
(BCM - AIR PRESSURE MONITOR) ......................

10

ECU DIAGNOSIS INFORMATION  ..............

13

BCM ....................................................................

13

List of ECU Reference  ............................................

13

WIRING DIAGRAM ......................................

14

TIRE PRESSURE MONITORING SYSTEM ......

14

Wiring Diagram ........................................................

14

BASIC INSPECTION  ...................................

17

DIAGNOSIS AND REPAIR WORK FLOW  .......

17

Work Flow ................................................................

17

ADDITIONAL SERVICE WHEN REPLACING 
BCM ...................................................................

19

Description ...............................................................

19

Work Procedure .......................................................

19

TIRE PRESSURE SENSOR ID REGISTRA-
TION ..................................................................

20

Description ...............................................................

20

Work Procedure .......................................................

20

DTC/CIRCUIT DIAGNOSIS  .........................

22

C1704, C1705, C1706, C1707 LOW TIRE 
PRESSURE .......................................................

22

DTC Logic ................................................................

22

Diagnosis Procedure  ...............................................

22

C1708, C1709, C1710, C1711 TIRE PRES-
SURE SENSOR .................................................

24

DTC Logic ................................................................

24

Diagnosis Procedure  ...............................................

24

C1716, C1717, C1718, C1719 TIRE PRES-
SURE SENSOR .................................................

26

DTC Logic ................................................................

26

Diagnosis Procedure  ...............................................

26

C1729 VEHICLE SPEED SIGNAL ....................

28

DTC Logic ................................................................

28

Diagnosis Procedure  ...............................................

28

POWER SUPPLY AND GROUND CIRCUIT  ....

29

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     679      680      681      682     ..