Nissan Juke (2016 year). Service Repair Manual - part 680

WCS-32

< WIRING DIAGRAM >

WARNING CHIME SYSTEM

JRNWF0722GB

Revision: November 2015

2016 JUKE

WCS

WARNING CHIME SYSTEM

WCS-33

< WIRING DIAGRAM >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

JRNWF0723GB

Revision: November 2015

2016 JUKE

WCS-34

< WIRING DIAGRAM >

WARNING CHIME SYSTEM

JRNWF0724GB

Revision: November 2015

2016 JUKE

WCS

WARNING CHIME SYSTEM

WCS-35

< WIRING DIAGRAM >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

JRNWF0725GB

Revision: November 2015

2016 JUKE

WCS-36

< WIRING DIAGRAM >

WARNING CHIME SYSTEM

JRNWF0726GB

Revision: November 2015

2016 JUKE

WCS

DIAGNOSIS AND REPAIR WORKFLOW

WCS-37

< BASIC INSPECTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

BASIC INSPECTION

DIAGNOSIS AND REPAIR WORKFLOW

Work Flow

INFOID:0000000012201481

OVERALL SEQUENCE

DETAILED FLOW

1.

OBTAIN INFORMATION ABOUT SYMPTOM

Interview the customer to obtain as much information as possible about the conditions and environment under

which the malfunction occurred.

>> GO TO 2.

2.

CHECK SYMPTOM

• Check the symptom based on the information obtained from the customer.

• Check if any other malfunctions are present.

>> GO TO 3.

3.

CHECK CONSULT SELF-DIAGNOSIS RESULTS

1. Connect CONSULT and perform self-diagnosis. Refer to 

WCS-19, "BUZZER : CONSULT Function (BCM

- BUZZER)"

 .

2. When DTC is detected, follow the instructions below:

-

Record DTC and Freeze Frame Data.

Are self-diagnosis results normal?

YES

>> GO TO 4.

NO

>> GO TO 5.

JSNIA4492GB

Revision: November 2015

2016 JUKE

WCS-38

< BASIC INSPECTION >

DIAGNOSIS AND REPAIR WORKFLOW

4.

NARROW DOWN MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS

Perform symptom diagnosis and narrow down the malfunctioning parts.

>> GO TO 5.

5.

REPAIR OR REPLACE MALFUNCTIONING PARTS

Repair or replace malfunctioning parts.

NOTE:

If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts.

>> GO TO 6.

6.

FINAL CHECK

Check that the warning buzzer in the combination meter operates normally.
Does it operate normally?

YES

>> INSPECTION END

NO

>> GO TO 1.

Revision: November 2015

2016 JUKE

WCS

POWER SUPPLY AND GROUND CIRCUIT

WCS-39

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

DTC/CIRCUIT DIAGNOSIS

POWER SUPPLY AND GROUND CIRCUIT

COMBINATION METER
COMBINATION METER : Diagnosis Procedure

INFOID:0000000012926228

1.

CHECK FUSE

Check for blown fuses.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Be sure to eliminate cause of malfunction before installing new fuse.

2.

CHECK POWER SUPPLY CIRCUIT

Check voltage between combination meter harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Check harness between combination meter and fuse.

3.

CHECK GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect combination meter connector.

3. Check continuity between combination meter harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair harness or connector.

Power source

Fuse No.

Battery

13

Ignition switch ON or START 

5

Ignition switch ACC or ON 

19

Terminals

Ignition switch po-

sition

Voltage

(Approx.)

(+)

(

−

)

Combination meter

Ground

Connector

Terminal

M34

27

OFF

Battery voltage

15

ACC

28

ON

Combination meter

Ground

Continuity

Connector

Terminal

M34

21

Existed

22

23

25

Revision: November 2015

2016 JUKE