Nissan Juke (2016 year). Service Repair Manual - part 671

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     669      670      671      672     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 671

 

 

INPUT SPEED SENSOR

TM-561

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

6. Remove O-ring (1) from input speed sensor.

INSTALLATION

Note the followings and installation is in the reverse order of removal.

CAUTION:

• Never reuse O-ring.

• Apply CVT fluid to the O-ring.

Inspection and Adjustment

INFOID:0000000012201256

INSPECTION AFTER INSTALLATION

Start the engine and check visually that there is no leakage of CVT fluid.

ADJUSTMENT AFTER INSTALLATION

If CVT fluid leaks during work, adjust the CVT fluid level. Refer to 

TM-441, "Adjustment"

.

JSDIA5196ZZ

Revision: November 2015

2016 JUKE

TM-562

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

PRIMARY SPEED SENSOR

PRIMARY SPEED SENSOR

Exploded View

INFOID:0000000012201257

Removal and Installation

INFOID:0000000012201258

REMOVAL

1. Turn ignition switch OFF.
2. Remove fender protector (LH). Refer to 

EXT-31, "Removal and Installation"

.

3. Disconnect primary speed sensor.
4. Remove mounting bolt (

) and remove primary speed sensor

(1) from transaxle assembly.

1.

Transaxle assembly

2.

Primary speed sensor

3.

O-ring

: Always replace after every disassembly.

: N·m (kg-m, in-lb)

: Apply CVT fluid

JSDIA6060GB

JSDIA6618ZZ

Revision: November 2015

2016 JUKE

PRIMARY SPEED SENSOR

TM-563

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

5. Remove O-ring (1) from primary speed sensor.

INSTALLATION

Note the followings and installation is in the reverse order of removal.

CAUTION:

• Never reuse O-ring.

• Apply CVT fluid to the O-ring.

Inspection and Adjustment

INFOID:0000000012201259

INSPECTION AFTER INSTALLATION

Start the engine and check visually that there is no leakage of CVT fluid.

ADJUSTMENT AFTER INSTALLATION

If CVT fluid leaks during work, adjust the CVT fluid level. Refer to 

TM-441, "Adjustment"

.

JSDIA5199ZZ

Revision: November 2015

2016 JUKE

TM-564

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

OUTPUT SPEED SENSOR

OUTPUT SPEED SENSOR

Exploded View

INFOID:0000000012201260

Removal and Installation

INFOID:0000000012201261

REMOVAL

1. Turn ignition switch OFF.
2. Disconnect output speed sensor connector.
3. Remove mounting bolt (

) and remove output speed sensor (1)

from transaxle assembly.

4. Remove O-ring (1) from output speed sensor.

1.

Transaxle assembly

2.

Output speed sensor

3.

O-ring

: Always replace after every disassembly.

: N·m (kg-m, in-lb)

: Apply CVT fluid

JSDIA5033GB

JSDIA5201ZZ

JSDIA5199ZZ

Revision: November 2015

2016 JUKE

OUTPUT SPEED SENSOR

TM-565

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

INSTALLATION

Note the followings and installation is in the reverse order of removal.

CAUTION:

• Never reuse O-ring.

• Apply CVT fluid to the O-ring.

Inspection and Adjustment

INFOID:0000000012201262

INSPECTION AFTER INSTALLATION

Start the engine and check visually that there is no leakage of CVT fluid.

ADJUSTMENT AFTER INSTALLATION

If CVT fluid leaks during work, adjust the CVT fluid level. Refer to 

TM-441, "Adjustment"

.

Revision: November 2015

2016 JUKE

TM-566

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

DIFFERENTIAL SIDE OIL SEAL

DIFFERENTIAL SIDE OIL SEAL

Exploded View

INFOID:0000000012201263

Removal and Installation

INFOID:0000000012201264

NOTE:

When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-

ing.

REMOVAL

Differential Side Oil Seal (Left Side)

1. Remove front drive shaft (left side). Refer to 

FAX-83, "2WD : Removal and Installation"

 (2WD), 

FAX-97,

"AWD : Removal and Installation"

 (AWD).

2. Remove differential side oil seal (1) using an oil seal remover

(commercial service tool) (A).

CAUTION:

Be careful not to scratch transaxle case and converter

housing.

Differential Side Oil Seal (Right Side)

1. Remove transfer assembly. Refer to 

FAX-83, "2WD : Removal and Installation"

 (2WD), 

FAX-97, "AWD :

Removal and Installation"

 (AWD).

1.

Transaxle assembly

2.

Differential side oil seal (transaxle 
case side)

3.

Differential side oil seal (converter 
housing side)

: Always replace after every disassembly.

: Apply CVT fluid

JSDIA6062ZZ

JPDIA0118ZZ

Revision: November 2015

2016 JUKE

DIFFERENTIAL SIDE OIL SEAL

TM-567

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

2. Remove differential side oil seal (1) using an oil seal remover

(commercial service tool) (A).

CAUTION:

Be careful not to scratch transaxle case and converter

housing.

INSTALLATION

Note the followings and installation is in the reverse order of removal.

Differential Side Oil Seal  (Transaxle Case Side)

CAUTION:

When inserting the drive shaft, be sure to use protector (SST: KV38107900).

1. Measure height (A) of seal lip. Calculate protrusion (C) of oil

seal lip according to measured height (A) of seal lip and refer-

ence value (B) of side oil insertion.

CAUTION:

• Never reuse differential side oil seal.

• Put a mark on the measurement area and measure height of seal lip at four points diagonally

using suitable tool.

NOTICE:

Since seal lips have a tolerance of 

±

 0.3 mm (

±

 0.012 in) at maximum due to manufacturing tolerances or

packing conditions, it is necessary to measure the seal lip height beforehand to clarify the tolerance.

2. As an indicator of the parallelism and insertion depth, cut a

masking tape (1) to specified width [add 1 mm (0.04 in) to the

value calculated from the tip of differential side oil seal lip] and

affix to the differential side oil seal.

3. Install the differential side oil seal using a drift [outer diameter:

53 mm (2.09 in), inner diameter: 50 mm (1.97 in)] according to

the guide of the masking tape. 

CAUTION:

• If differential side oil seal is inserted deeper than the ref-

erence value, use a new differential side oil seal and per-

form the steps again.

• Apply ATF to the differential side oil seal lip and around

the oil seal.

NOTE:

A hub cap (Part No. 43234 1HA0A) can be used as a substitute for drift. To use a hub cap, be sure to pre-

pare a new one specifically for patting seal.

4. Remove masking tape.
5. Adjust as instructed below to optimize the protrusion size and parallelism.

CAUTION:

If differential side oil seal is inserted deeper than the reference value, use a new differential side

oil seal and perform the steps again.

JPDIA0118ZZ

(1)

: Differential side oil seal 

(2)

: Transaxle case

Lip protrusion (C)

: C=A–B

Differential side oil seal insertion 
reference value (B)

: 1.8 mm (0.071 in)

JSDIA4816ZZ

JSDIA4817ZZ

Revision: November 2015

2016 JUKE

TM-568

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

DIFFERENTIAL SIDE OIL SEAL

• Protrusion size (A)

CAUTION:

Protrusion must fall within 

±

 0.5mm (0.020 in) of calcu-

lated size.

• Parallelism at four diagonal points (

)

CAUTION:

The difference among four diagonal points must be within

0.3 mm (0.012 in).

NOTE:

If differential side oil seal is uneven while installing, tilt suitable

tool.

6. Check that the protrusion size and parallelism are adequate.

Differential Side Oil Seal (Converter housing Side) (2WD Models)

CAUTION:

When inserting the drive shaft, be sure to use protector (SST: KV38107900).

1. Measure height (A) of seal lip. Calculate protrusion (C) of oil

seal lip according to measured height (A) of seal lip and refer-

ence value (B) of side oil insertion.

CAUTION:

• Never reuse differential side oil seal.

• Put a mark on the measurement area and measure height of seal lip at four points diagonally

using suitable tool.

NOTICE:

Since seal lips have a tolerance of 

±

 0.3 mm (

±

 0.012 in) at maximum due to manufacturing tolerances or

packing conditions, it is necessary to measure the seal lip height beforehand to clarify the tolerance.

2. As an indicator of the parallelism and insertion depth, cut a

masking tape (1) to specified width [add 1 mm (0.04 in) to the

value calculated from the tip of differential side oil seal lip] and

affix to the differential side oil seal.

3. Install the differential side oil seal using a drift [outer diameter:

53 mm (2.09 in), inner diameter: 50 mm (1.97 in)] according to

the guide of the masking tape. 

CAUTION:

• If differential side oil seal is inserted deeper than the ref-

erence value, use a new differential side oil seal and per-

form the steps again.

• Apply ATF to the differential side oil seal lip and around

the oil seal.

NOTE:

JSDIA4815ZZ

JSDIA4814ZZ

(1)

: Differential side oil seal 

(2)

: Transaxle case

Lip protrusion (C)

: C=A–B

Differential side oil seal insertion 
reference value (B)

: 2.2 mm (0.087 in)

JSDIA4816ZZ

JSDIA4817ZZ

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     669      670      671      672     ..