Nissan Juke (2016 year). Service Repair Manual - part 670

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     668      669      670      671     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 670

 

 

PADDLE SHIFTER

TM-553

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

5. Remove the paddle shifter connector (C) and (D) from paddle

shifter.

6. Remove the paddle shifter mounting bolts (E) and nuts (F).
7. Remove the paddle shifter from the steering column assembly.

INSTALLATION

Installation is in the reverse order of removal.

A

: Side of paddle shifter (shift-down switch)

B

: Side of paddle shifter (shift-up switch)

AWDIA0563ZZ

Revision: November 2015

2016 JUKE

TM-554

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

TCM

TCM

Exploded View

INFOID:0000000012201246

Removal and Installation

INFOID:0000000012201247

CAUTION:

• Never impact on TCM when removing or installing TCM.

• When replacing TCM, note the “CVTF DETERIORATION DATE” value displayed on CONSULT “CON-

FORM CVTF DETERIORTN” in MAINTENANCE BOOKLET, before start the operation.

• When replacing TCM and transaxle assembly simultaneously, replace transaxle assembly first and

then replace TCM. 

• Before replacing TCM, perform “ADDITIONAL SERVICE WHEN REPLACING TCM”. Refer to 

TM-429,

"Work Procedure"

.

REMOVAL

1. Remove the battery. Refer to 

PG-105, "Removal and Installation"

.

2. Remove air duct (inlet) and air cleaner case. Refer to 

EM-192, "Removal and Installation"

.

3. Disconnect the TCM connector.
4. Remove the TCM.
5. Remove the bracket.

INSTALLATION

Installation is in the reverse order of removal.

Adjustment

INFOID:0000000012201248

ADJUSTMENT AFTER INSTALLATION

When replaced TCM, perform "ADDITIONAL SERVICE WHEN REPLACING TCM". Refer to 

TM-429, "Work

Procedure"

.

1.

Bracket

2.

TCM

:Vehicle front

: N·m (kg-m, in-lb)

JSDIA7186GB

Revision: November 2015

2016 JUKE

AIR BREATHER HOSE

TM-555

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

AIR BREATHER HOSE

Exploded View

INFOID:0000000012201249

Removal and Installation

INFOID:0000000012201250

REMOVAL

1. Remove air cleaner case. Refer to 

EM-192, "Removal and Installation"

.

2. Remove clip of air breather hose from harness bracket.
3. Remove air breather hose from transaxle assembly.

INSTALLATION

Note the followings and installation is in the reverse order of removal.

CAUTION:

• Never bend the air breather hose to prevent damage to the hose.

• Insert air breather hose (1) to air breather tube (A) all the way

to the curve of the tube.

• Insert air breather hose to air breather tube so that the paint

mark (B) is facing upward.

1.

Air breather hose

2.

Clip

3.

Transaxle assembly

4.

Air breather tube

5.

Harness bracket

: Vehicle front

: Always replace after every disassembly.

JSDIA6058ZZ

JSDIA2399ZZ

Revision: November 2015

2016 JUKE

TM-556

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

AIR BREATHER HOSE

• Never reuse clip (A).

• Securely install the clip to the harness bracket.

JSDIA2458ZZ

Revision: November 2015

2016 JUKE

OIL PAN

TM-557

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

OIL PAN

Exploded View

INFOID:0000000012201251

Removal and Installation

INFOID:0000000012201252

REMOVAL

1. Remove drain plug   from oil pan and then drain the CVT fluid.

Transaxle assembly

Oil pan gasket

Magnet

Oil pan

Drain plug

Drain plug gasket

Overflow plug

O-ring

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

: N·m (kg-m, in-lb)

: Apply CVT fluid

JSDIA7928GB

JSDIA5205ZZ

Revision: November 2015

2016 JUKE

TM-558

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

OIL PAN

2. Remove drain plug gasket  .

3. Remove oil pan bolts (

).

4. Remove oil pan from transaxle case.

5. Remove oil pan gasket   from oil pan.

6. Remove magnets   from oil pan.

INSTALLATION

Note the followings and installation is in the reverse order of removal.

CAUTION:

• Never reuse oil pan gasket.

• Never reuse drain plug gasket.

• Never reuse O-ring.

• Completely clean the iron powder from the magnet area of oil pan and the magnets.

• Install the oil pan to the transaxle case with the following procedure.

1. Install the oil pan gasket to the oil pan.

CAUTION:

JSDIA5206ZZ

: Vehicle front

JSDIA5207ZZ

JSDIA7929ZZ

JSDIA7930ZZ

Revision: November 2015

2016 JUKE

OIL PAN

TM-559

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Completely wipe out any moisture, oil, and old gasket from the oil pan gasket surface and bolt

hole of oil pan and transaxle case.

2. Install the oil pan assembly to the transaxle case, and then temporarily tighten the oil pan bolt.

3. Tighten the oil pan bolts in the order shown to the specified

torque.

4. Tighten the oil pan bolts again clockwise from (1) shown to the

specified torque.

• Fill with CVT fluid after installation. Refer to 

TM-440, "Replace-

ment"

.

Inspection

INFOID:0000000012201253

INSPECTION AFTER REMOVAL

Check oil pan for foreign material.

• If a large amount of worn material is found, clutch plate may be worn.

• If iron powder is found, bearings, gears, or clutch plates may be worn.

• If aluminum powder is found, bushing may be worn, or chips or burrs of aluminum casting parts may enter.

Check points where wear is found in all cases.

INSPECTION AFTER INSTALLATION

Start the engine and check visually that there is no leakage of CVT fluid.

: Vehicle front

JSDIA5211ZZ

Revision: November 2015

2016 JUKE

TM-560

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

INPUT SPEED SENSOR

INPUT SPEED SENSOR

Exploded View

INFOID:0000000012201254

Removal and Installation

INFOID:0000000012201255

REMOVAL

NOTE:

When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-

ing.
1. Turn ignition switch OFF.
2. Remove battery and battery support. Refer to 

PG-105, "Removal and Installation"

.

3. Remove ECM and bracket as a set. Refer to 

EC-1256, "Removal and Installation"

.

4. Disconnect input speed sensor connector.
5. Remove mounting bolt (

) and remove input speed sensor (1)

from transaxle assembly.

1.

Transaxle assembly

2.

O-ring

3.

Input speed sensor

: Always replace after every disassembly.

: N·m (kg-m, in-lb)

: Apply CVT fluid

JSDIA6059GB

JSDIA6619ZZ

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     668      669      670      671     ..