Nissan Juke (2016 year). Service Repair Manual - part 587

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     585      586      587      588     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 587

 

 

B0098 FRONT DOOR SATELLITE SENSOR RH

SRC-63

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000012199615

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK DTC

Perform each inspection according to the displayed DTC.
Which DTC is displayed?

[B0098–86]              >> GO TO 4.

Other than the above >> GO TO 2.

2.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 3.

NO-1 >> Damage: Replace malfunctioning harness and connector.

NO-2 >> Disconnection or looseness: Securely lock the connector.

3.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 4. 

NO

>> Replace malfunctioning harness and connector.

4.

REPLACE FRONT DOOR SATELLITE SENSOR RH

1. Replace front door satellite sensor RH. Refer to 

SR-26, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-62, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 5. 

NO

>> INSPECTION END

5.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to 

SR-29, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-62, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Revision: November 2015

2016 JUKE

SRC-64

< DTC/CIRCUIT DIAGNOSIS >

B00A0 OCCUPANT DETECTION SYSTEM CONTROL UNIT

B00A0 OCCUPANT DETECTION SYSTEM CONTROL UNIT

DTC Description

INFOID:0000000012199616

DTC DETECTION LOGIC

POSSIBLE CAUSE

OCCUPANT SENS

• [B00A0–00]

- Connection malfunction or short circuit to power supply of harness or connector

- Internal malfunction of occupant detection sensor

- Internal malfunction of air bag diagnosis sensor unit

• [B00A0–02, B00A0–09]

- Connection malfunction of harness and connector

- Internal malfunction of occupant detection sensor

- Internal malfunction of air bag diagnosis sensor unit

OCCUPANT SENS C/U

• [B00A0–04, B00A0–83, B00A0–86, B00A0–87, B00A0–88, B00A0–8F]

- Connection malfunction or open circuit of harness and connector

- Internal malfunction of occupant detection sensor control unit

- Internal malfunction of air bag diagnosis sensor unit

• [B00A0–93]

- Connection malfunction of harness and connector

- Internal malfunction of occupant detection sensor control unit

- Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

DTC

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

B00A0–00

OCCUPANT SENS
[Occupant Classification 
System (Subfault)]

[ABNORMAL VOLTAGE]

Power supply malfunction of occupant detection sensor

B00A0–02

[UNIT MALFUNC]

Malfunction of occupant detection sensor

B00A0–09

[UNIT MALFUNC]

Malfunction of occupant detection sensor

B00A0–04

OCCUPANT SENS C/U 
[Occupant Classification 
System (Subfault)]

[UNIT MALFUNC]

Malfunction of occupant detection sensor control unit

B00A0–83

[COMM ERR]

• Communication malfunction of occupant detection sensor con-

trol unit

• Communication blank of occupant detection sensor control 

unit

B00A0–86

[COMM ERR]

• Communication malfunction of occupant detection sensor con-

trol unit

• Communication blank of occupant detection sensor control 

unit

B00A0–87

[COMM ERR]

• Communication malfunction of occupant detection sensor con-

trol unit

• Communication blank of occupant detection sensor control 

unit

B00A0–88

[COMM ERR]

• Communication malfunction of occupant detection sensor con-

trol unit

• Communication blank of occupant detection sensor control 

unit

B00A0–8F

[UNDEFINED]

Undefined status of occupant detection sensor control unit

B00A0–93

[RESET]

Reset malfunction of occupant detection sensor control unit

Revision: November 2015

2016 JUKE

B00A0 OCCUPANT DETECTION SYSTEM CONTROL UNIT

SRC-65

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

 With CONSULT

1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-10, "On Board Diagnosis Function"

.

NOTE:

SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-65, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-45, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000012199617

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?

YES

>> GO TO 2.

NO–1 >> Damage: Replace malfunctioning harness and connector.

NO–2 >> Disconnection or looseness: Securely lock the connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace malfunctioning harness and connector.

3.

REPLACE OCCUPANT DETECTION SYSTEM CONTROL UNIT

1. Replace occupant detection system control unit. Refer to 

SR-32, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-64, "DTC Description"

.

Is DTC detected?

YES

>>  GO TO 4.

NO

>> INSPECTION END

4.

REPLACE OCCUPANT DETECTION SYSTEM SEAT SENSOR

1. Replace seat frame. Refer to 

SE-21, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-64, "DTC Description"

.

Is DTC detected?

YES

>>  GO TO 5.

NO

>> INSPECTION END

5.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to 

SR-29, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-64, "DTC Description"

.

Is DTC detected?

YES

>>  GO TO 1.

NO

>> INSPECTION END

Revision: November 2015

2016 JUKE

SRC-66

< DTC/CIRCUIT DIAGNOSIS >

B00D5 PASSENGER AIR BAG OFF INDICATOR

B00D5 PASSENGER AIR BAG OFF INDICATOR

DTC Description

INFOID:0000000012199618

DTC DETECTION LOGIC

POSSIBLE CAUSE

[B00D5–04]

• Internal malfunction of front passenger air bag OFF indicator

• Internal malfunction of air bag diagnosis sensor unit

[B00D5–11]

• Connection malfunction or short circuit to ground of harness and connector

• Internal malfunction of front passenger air bag OFF indicator

• Internal malfunction of air bag diagnosis sensor unit

[B00D5–12]

• Connection malfunction or short circuit to power supply of harness and connector

• Internal malfunction of front passenger air bag OFF indicator

• Internal malfunction of air bag diagnosis sensor unit

[B00D5–13]

• Connection malfunction or open circuit of harness and connector

• Internal malfunction of front passenger air bag OFF indicator

• Internal malfunction of air bag diagnosis sensor unit

[B00D5–15]

• Connection malfunction or short circuit to power supply of harness and connector

• Connection malfunction or open circuit of harness and connector

• Internal malfunction of front passenger air bag OFF indicator

• Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-10, "On Board Diagnosis Function"

.

NOTE:

SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-67, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-45, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

DTC

CONSULT screen items

DTC detecting condition

B00D5–04

PASS A/B INDCTR CKT [UNIT MALFUNC]

Malfunction in passenger air bag OFF indicator circuit

B00D5–11

PASS A/B INDCTR CKT [GND-SHORT]

Passenger air bag OFF indicator circuit is shorted to ground

B00D5–12

PASS A/B INDCTR CKT [VB-SHORT]

Passenger air bag OFF indicator circuit is shorted to power supply cir-
cuit

B00D5–13

PASS A/B INDCTR CKT [OPEN]

Passenger air bag OFF indicator circuit is open

B00D5–15

PASS A/B INDCTR CKT [PWE-SHORT/
OPEN]

Passenger air bag OFF indicator circuit is open or shorted to power 
supply circuit

Revision: November 2015

2016 JUKE

B00D5 PASSENGER AIR BAG OFF INDICATOR

SRC-67

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

Diagnosis Procedure

INFOID:0000000012199619

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

CHECK PASSENGER AIR BAG OFF INDICATOR

1. Replace cluster lid C (passenger air bag OFF indicator).

2. Perform DTC confirmation procedure. Refer to 

SRC-66, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to 

SR-29, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-66, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Revision: November 2015

2016 JUKE

SRC-68

< DTC/CIRCUIT DIAGNOSIS >

B1400, B1401, B1402, B1403, B1404, B1405 AIR BAG DIAGNOSIS SENSOR 

UNIT

B1400, B1401, B1402, B1403, B1404, B1405 AIR BAG DIAGNOSIS SEN-
SOR UNIT

DTC Description

INFOID:0000000012199620

DTC DETECTION LOGIC

POSSIBLE CAUSE

Malfunction in air bag diagnosis sensor unit

FAIL-SAFE

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-10, "On Board Diagnosis Function"

.

NOTE:

SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-68, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-45, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000012199621

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?

DTC

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

B1400–00

CONTROL UNIT 
(airbag control unit)

[UNIT MALFUNC]

Air bag diagnosis sensor unit is malfunctioning

B1401–00

CONTROL UNIT 
(airbag control unit internal 
trouble, sensor2)

[UNIT MALFUNC]

B1402–00

CONTROL UNIT 
(airbag control unit internal 
trouble, sensor3)

[UNIT MALFUNC]

B1403–00

CONTROL UNIT 
(airbag control unit internal 
trouble, sensor4)

[UNIT MALFUNC]

B1404–00

CONTROL UNIT 
(airbag control unit internal 
trouble, sensor5)

[UNIT MALFUNC]

B1405–00

CONTROL UNIT 
(airbag control unit internal 
trouble, sensor6)

[UNIT MALFUNC]

Revision: November 2015

2016 JUKE

B1400, B1401, B1402, B1403, B1404, B1405 AIR BAG DIAGNOSIS SENSOR 

UNIT

SRC-69

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 2.

NO–1 >> Damage: Replace malfunctioning harness and connector.

NO–2 >> Disconnection or looseness: Securely lock the connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace malfunctioning harness and connector.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to 

SR-29, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-68, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Revision: November 2015

2016 JUKE

SRC-70

< DTC/CIRCUIT DIAGNOSIS >

B1406, B1407, B1408, B1409, B1410 AIR BAG DIAGNOSIS SENSOR UNIT

B1406, B1407, B1408, B1409, B1410 AIR BAG DIAGNOSIS SENSOR UNIT

DTC Description

INFOID:0000000012199622

DTC DETECTION LOGIC

POSSIBLE CAUSE

Malfunction in air bag diagnosis sensor unit

FAIL-SAFE

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-10, "On Board Diagnosis Function"

.

NOTE:

SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-70, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-45, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000012199623

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?

YES

>> GO TO 2.

NO–1 >> Damage: Replace malfunctioning harness and connector.

NO–2 >> Disconnection or looseness: Securely lock the connector.

DTC

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

B1406–00

CONTROL UNIT 
(airbag control unit internal 
trouble, Energy Reserver)

[UNIT MALFUNC]

Air bag diagnosis sensor unit is malfunctioning

B1407–00

CONTROL UNIT 
(airbag control unit internal 
trouble, driver IC1)

[UNIT MALFUNC]

B1408–00

CONTROL UNIT 
(airbag control unit internal 
trouble, driver IC2)

[UNIT MALFUNC]

B1409–00

CONTROL UNIT 
(airbag control unit internal 
trouble, driver IC3)

[UNIT MALFUNC]

B1410–00

CONTROL UNIT 
(airbag control unit internal 
trouble, Power IC)

[UNIT MALFUNC]

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     585      586      587      588     ..