Nissan Juke (2016 year). Service Repair Manual - part 585

B0020 SIDE AIR BAG MODULE

SRC-47

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?

YES

>> GO TO 2.

NO–1 >> Damage: Replace malfunctioning harness and connector.

NO–2 >> Disconnection or looseness: Securely lock the connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace malfunctioning harness and connector.

3.

REPLACE SIDE AIR BAG MODULE LH

1. Replace side air bag module LH. Refer to 

SE-21, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-46, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to 

SR-29, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-46, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

Revision: November 2015

2016 JUKE

SRC-48

< DTC/CIRCUIT DIAGNOSIS >

B0021 CURTAIN AIR BAG MODULE

B0021 CURTAIN AIR BAG MODULE

DTC Description

INFOID:0000000012199600

DTC DETECTION LOGIC

POSSIBLE CAUSE

[B0021–09, B0021–1A]

• Connection malfunction or short circuit of harness and connector

• Internal malfunction of curtain air bag module LH

• Internal malfunction of air bag diagnosis sensor unit

[B0021–11]

• Connection malfunction or short circuit to ground of harness and connector

• Internal malfunction of curtain air bag module LH

• Internal malfunction of air bag diagnosis sensor unit

[B0021–12]

• Connection malfunction or short circuit to power supply of harness and connector

• Internal malfunction of curtain air bag module LH

• Internal malfunction of air bag diagnosis sensor unit

[B0021–13]

• Connection malfunction or open circuit of harness and connector

• Internal malfunction of curtain air bag module LH

• Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-10, "On Board Diagnosis Function"

.

NOTE:

SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-48, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-45, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000012199601

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

DTC

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

B0021–09

CURTAIN A/B MODULE LH 
[Left Curtain Deployment 
Control 1 (Subfault)]

[SHORT]

Curtain air bag module LH circuits are shorted to each other

B0021–11

[GND-SHORT]

Curtain air bag module LH circuit is shorted to ground

B0021–12

[VB-SHORT]

Curtain air bag module LH circuit is shorted to power supply circuit

B0021–13

[OPEN]

Curtain air bag module LH circuit is open

B0021–1A

[SHORT]

Curtain air bag module LH circuits are shorted to each other

Revision: November 2015

2016 JUKE

B0021 CURTAIN AIR BAG MODULE

SRC-49

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?

YES

>> GO TO 2.

NO–1 >> Damage: Replace malfunctioning harness and connector.

NO–2 >> Disconnection or looseness: Securely lock the connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace malfunctioning harness and connector.

3.

REPLACE CURTAIN AIR BAG MODULE LH

1. Replace curtain air bag module LH. Refer to 

SR-21, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-48, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to 

SR-29, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-48, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

Revision: November 2015

2016 JUKE

SRC-50

< DTC/CIRCUIT DIAGNOSIS >

B0028 SIDE AIR BAG MODULE

B0028 SIDE AIR BAG MODULE

DTC Description

INFOID:0000000012199602

DTC DETECTION LOGIC

POSSIBLE CAUSE

[B0028–09, B0028–1A]

• Connection malfunction or short circuit of harness and connector

• Internal malfunction of side air bag module RH

• Internal malfunction of air bag diagnosis sensor unit

[B0028–11]

• Connection malfunction or short circuit to ground of harness and connector

• Internal malfunction of side air bag module RH

• Internal malfunction of air bag diagnosis sensor unit

[B0028–12]

• Connection malfunction or short circuit to power supply of harness and connector

• Internal malfunction of side air bag module RH

• Internal malfunction of air bag diagnosis sensor unit

[B0028–13]

• Connection malfunction or open circuit of harness and connector

• Internal malfunction of side air bag module RH

• Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-10, "On Board Diagnosis Function"

.

NOTE:

SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-50, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-45, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000012199603

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

DTC

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

B0028–09

SIDE A/B MODULE RH 
[Right Side Airbag Deploy-
ment Control (Subfault)]

[SHORT]

Side air bag module RH circuits are shorted to each other

B0028–11

[GND-SHORT]

Side air bag module RH circuit is shorted to ground

B0028–12

[VB-SHORT]

Side air bag module RH circuit is shorted to power supply circuit

B0028–13

[OPEN]

Side air bag module RH circuit is open

B0028–1A

[SHORT]

Side air bag module RH circuits are shorted to each other

Revision: November 2015

2016 JUKE

B0028 SIDE AIR BAG MODULE

SRC-51

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?

YES

>> GO TO 2.

NO–1 >> Damage: Replace malfunctioning harness and connector.

NO–2 >> Disconnection or looseness: Securely lock the connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace malfunctioning harness and connector.

3.

REPLACE SIDE AIR BAG MODULE RH

1. Replace side air bag module RH. Refer to 

SE-21, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-50, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to 

SR-29, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-50, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

Revision: November 2015

2016 JUKE

SRC-52

< DTC/CIRCUIT DIAGNOSIS >

B0029 CURTAIN AIR BAG MODULE

B0029 CURTAIN AIR BAG MODULE

DTC Description

INFOID:0000000012199604

DTC DETECTION LOGIC

POSSIBLE CAUSE

[B0029–09, B0029–1A]

• Connection malfunction or short circuit of harness and connector

• Internal malfunction of curtain air bag module RH

• Internal malfunction of air bag diagnosis sensor unit

[B0029–11]

• Connection malfunction or short circuit to ground of harness and connector

• Internal malfunction of curtain air bag module RH

• Internal malfunction of air bag diagnosis sensor unit

[B0029–12]

• Connection malfunction or short circuit to power supply of harness and connector

• Internal malfunction of curtain air bag module RH

• Internal malfunction of air bag diagnosis sensor unit

[B0029–13]

• Connection malfunction or open circuit of harness and connector

• Internal malfunction of curtain air bag module RH

• Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-10, "On Board Diagnosis Function"

.

NOTE:

SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-52, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-45, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000012199605

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

DTC

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

B0029–09

CURTAIN A/B MODULE RH 
[Right Curtain Deployment 
Control 1 (Subfault)]

[SHORT]

Curtain air bag module RH circuits are shorted to each other

B0029–11

[GND-SHORT]

Curtain air bag module RH circuit is shorted to ground

B0029–12

[VB-SHORT]

Curtain air bag module RH circuit is shorted to power supply circuit

B0029–13

[OPEN]

Curtain air bag module RH circuit is open

B0029–1A

[SHORT]

Curtain air bag module RH circuits are shorted to each other

Revision: November 2015

2016 JUKE

B0029 CURTAIN AIR BAG MODULE

SRC-53

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?

YES

>> GO TO 2.

NO–1 >> Damage: Replace malfunctioning harness and connector.

NO–2 >> Disconnection or looseness: Securely lock the connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace malfunctioning harness and connector.

3.

REPLACE CURTAIN AIR BAG MODULE RH

1. Replace curtain air bag module RH. Refer to 

SR-21, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-52, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to 

SR-29, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-52, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

Revision: November 2015

2016 JUKE

SRC-54

< DTC/CIRCUIT DIAGNOSIS >

B0091 B-PILLAR SATELLITE SENSOR

B0091 B-PILLAR SATELLITE SENSOR

DTC Description

INFOID:0000000012199606

DTC DETECTION LOGIC

POSSIBLE CAUSE

[B0091–11]

• Connection malfunction or short circuit to ground of harness and connector

• Internal malfunction of satellite sensor LH

• Internal malfunction of air bag diagnosis sensor unit

[B0091–23, B0091–24, B0091–25, B0091–28]

• Internal malfunction of satellite sensor LH

• Internal malfunction of air bag diagnosis sensor unit

[B0091–81, B0091–93]

• Connection malfunction of harness or connector

• Internal malfunction of satellite sensor LH

• Internal malfunction of air bag diagnosis sensor unit

[B0091–86]

• Air bag diagnosis sensor unit and satellite sensor LH is different from the part specified

[B0091–88]

• Connection malfunction or open circuit of harness and connector

• Internal malfunction of satellite sensor LH

• Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-10, "On Board Diagnosis Function"

.

NOTE:

SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-55, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-45, "Intermittent Incident"

.

DTC

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

B0091–11

B-PILLAR SAT SEN LH 
[Left Side Restraints 
Sensor 1 (Subfault)]

[GND-SHORT]

Satellite sensor LH circuit is shorted to ground

B0091–23

[LOWER LIMIT ERR]

Lower limit value malfunction of satellite sensor LH

B0091–24

[UPPER LIMIT ERR]

Upper limit value malfunction of satellite sensor LH

B0091–25

[SELF-DIAG ERR]

Diagnosis malfunction of satellite sensor LH

B0091–28

[OFFSET ERR]

Offset malfunction of satellite sensor LH

B0091–81

[COMM ERR]

Communication malfunction of satellite sensor LH

B0091–86

[UNMATCH]

Satellite sensor LH is out of the specified specification

B0091–88

[OPEN]

Satellite sensor LH circuit is open

B0091–93

[RESET]

Reset malfunction of satellite sensor LH

Revision: November 2015

2016 JUKE