Nissan Juke (2016 year). Service Repair Manual - part 584

B0002 DRIVER AIR BAG MODULE

SRC-39

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B0002 DRIVER AIR BAG MODULE

DTC Description

INFOID:0000000012199592

DTC DETECTION LOGIC

POSSIBLE CAUSE

[B0002–00, B0002–09, B0002–1A]

• Connection malfunction or short circuit of harness and connector

• Internal malfunction of driver air bag module

• Internal malfunction of air bag diagnosis sensor unit

[B0002–11]

• Connection malfunction or short circuit to ground of harness and connector

• Internal malfunction of driver air bag module

• Internal malfunction of air bag diagnosis sensor unit

[B0002–12]

• Connection malfunction or short circuit to power supply of harness and connector

• Internal malfunction of driver air bag module

• Internal malfunction of air bag diagnosis sensor unit

[B0002–13]

• Connection malfunction or open circuit of harness and connector

• Internal malfunction of driver air bag module

• Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-10, "On Board Diagnosis Function"

.

NOTE:

SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-40, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-45, "Intermittent Incident"

.

DTC

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

B0002–00

DRIVER AIRBAG MODULE 2
[Driver Frontal Stage 2 De-
ployment Control (Subfault)]

[SHORT]

Driver air bag module circuits   are shorted to each other
(including the spiral cable)

B0002–09

[SHORT]

Driver air bag module circuits   are shorted to each other
(including the spiral cable)

B0002–11

[GND-SHORT]

Driver air bag module circuit is shorted to ground
(including the spiral cable)

B0002–12

[VB-SHORT]

Driver air bag module circuit is shorted to power supply circuit
(including the spiral cable)

B0002–13

[OPEN]

Driver air bag module circuit is open
(including the spiral cable)

B0002–1A

[SHORT]

Driver air bag module circuits   are shorted to each other
(including the spiral cable)

Revision: November 2015

2016 JUKE

SRC-40

< DTC/CIRCUIT DIAGNOSIS >

B0002 DRIVER AIR BAG MODULE

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000012199593

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?

YES

>> GO TO 2.

NO–1 >> Damage: Replace malfunctioning harness and connector.

NO–2 >> Disconnection or looseness: Securely lock the connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace malfunctioning harness and connector.

3.

CHECK DTC

Perform each inspection according to the displayed DTC.
Which DTC is displayed?

[B0002–13]>>GO TO 4.

[B0002–12]>>GO TO 8.

[B0002–11]>>GO TO 5.

[B0002–00, B0002–09, B0002–1A]>>GO TO 6.

4.

CHECK SPIRAL CABLE CIRCUIT 1

1. Turn ignition switch OFF.

2. Disconnect driver air bag module connector and combination switch (spiral cable) connector.

3. Check continuity between spiral cable terminals.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Replace spiral cable. Refer to 

SR-15, "Removal and Installation"

.

5.

CHECK SPIRAL CABLE CIRCUIT 2

1. Turn ignition switch OFF.

2. Disconnect driver air bag module connector and combination switch (spiral cable) connector.

3. Check continuity between spiral cable terminal and ground.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Replace spiral cable. Refer to 

SR-15, "Removal and Installation"

.

6.

CHECK SPIRAL CABLE CIRCUIT 3

1. Turn ignition switch OFF.

Terminal

Continuity 

12

29

Existed

9

30

Terminal

Ground

Continuity 

12

Not existed

9

Revision: November 2015

2016 JUKE

B0002 DRIVER AIR BAG MODULE

SRC-41

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

2. Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-

nector.

3. Check continuity between spiral cable terminals.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace spiral cable. Refer to 

SR-15, "Removal and Installation"

.

7.

CHECK SPIRAL CABLE CIRCUIT 4

Check continuity between spiral cable terminals.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Replace spiral cable. Refer to 

SR-15, "Removal and Installation"

.

8.

REPLACE SPIRAL CABLE

1. Replace spiral cable. Refer to 

GI-45, "Intermittent Incident"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-39, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 9.

NO

>> INSPECTION END

9.

REPLACE DRIVER AIR BAG MODULE

1. Replace driver air bag module. Refer to 

SR-12, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-39, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 10.

NO

>> INSPECTION END

10.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to 

SR-29, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-39, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Terminal

Continuity 

12

9

Not existed

Terminal

Continuity 

29

30

Not existed

Revision: November 2015

2016 JUKE

SRC-42

< DTC/CIRCUIT DIAGNOSIS >

B0010 PASSENGER AIR BAG MODULE

B0010 PASSENGER AIR BAG MODULE

DTC Description

INFOID:0000000012199594

DTC DETECTION LOGIC

POSSIBLE CAUSE

[B0010–09, B0010–1A]

• Connection malfunction or short circuit of harness and connector

• Internal malfunction of passenger air bag module

• Internal malfunction of air bag diagnosis sensor unit

[B0010–11]

• Connection malfunction or short circuit to ground of harness and connector

• Internal malfunction of passenger air bag module

• Internal malfunction of air bag diagnosis sensor unit

[B0010–12]

• Connection malfunction or short circuit to power supply of harness and connector

• Internal malfunction of passenger air bag module

• Internal malfunction of air bag diagnosis sensor unit

[B0010–13]

• Connection malfunction or open circuit of harness and connector

• Internal malfunction of passenger air bag module

• Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-10, "On Board Diagnosis Function"

.

NOTE:

SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-42, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-45, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000012199595

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

DTC

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

B0010–09

ASSIST A/B MODULE
[Passenger Frontal Stage 
1 Deployment Control 
(Subfault)]

[SHORT]

Passenger air bag module circuits   are shorted to each other

B0010–11

[GND-SHORT]

Passenger air bag module circuit is shorted to ground

B0010–12

[VB-SHORT]

Passenger air bag module circuit is shorted to power supply circuit

B0010–13

[OPEN]

Passenger air bag module circuit is open

B0010–1A

[SHORT]

Passenger air bag module circuits   are shorted to each other

Revision: November 2015

2016 JUKE

B0010 PASSENGER AIR BAG MODULE

SRC-43

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?

YES

>> GO TO 2.

NO–1 >> Damage: Replace malfunctioning harness and connector.

NO–2 >> Disconnection or looseness: Securely lock the connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace malfunctioning harness and connector.

3.

REPLACE PASSENGER AIR BAG MODULE

1. Replace passenger air bag module. Refer to 

SR-18, "Removal and Installation"

2. Perform DTC confirmation procedure. Refer to 

SRC-42, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to 

SR-29, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-42, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Revision: November 2015

2016 JUKE

SRC-44

< DTC/CIRCUIT DIAGNOSIS >

B0011 PASSENGER AIR BAG MODULE

B0011 PASSENGER AIR BAG MODULE

DTC Description

INFOID:0000000012199596

DTC DETECTION LOGIC

POSSIBLE CAUSE

[B0011–09, B0011–1A]

• Connection malfunction or short circuit of harness and connector

• Internal malfunction of passenger air bag module

• Internal malfunction of air bag diagnosis sensor unit

[B0011–11]

• Connection malfunction or short circuit to ground of harness and connector

• Internal malfunction of passenger air bag module

• Internal malfunction of air bag diagnosis sensor unit

[B0011–12]

• Connection malfunction or short circuit to power supply of harness and connector

• Internal malfunction of passenger air bag module

• Internal malfunction of air bag diagnosis sensor unit

[B0011–13]

• Connection malfunction or open circuit of harness and connector

• Internal malfunction of passenger air bag module

• Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-10, "On Board Diagnosis Function"

.

NOTE:

SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-44, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-45, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000012199597

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

DTC

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

B0011–09

ASSIST A/B MODULE 2
[Passenger Frontal Stage 
2 Deployment Control 
(Subfault)]

[SHORT]

Passenger air bag module circuits   are shorted to each other

B0011–11

[GND-SHORT]

Passenger air bag module circuit is shorted to ground

B0011–12

[VB-SHORT]

Passenger air bag module circuit is shorted to power supply circuit

B0011–13

[OPEN]

Passenger air bag module circuit is open

B0011–1A

[SHORT]

Passenger air bag module circuits   are shorted to each other

Revision: November 2015

2016 JUKE

B0011 PASSENGER AIR BAG MODULE

SRC-45

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?

YES

>> GO TO 2.

NO–1 >> Damage: Replace malfunctioning harness and connector.

NO–2 >> Disconnection or looseness: Securely lock the connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace malfunctioning harness and connector.

3.

REPLACE PASSENGER AIR BAG MODULE

1. Replace passenger air bag module. Refer to 

SR-18, "Removal and Installation"

2. Perform DTC confirmation procedure. Refer to 

SRC-44, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to 

SR-29, "Removal and Installation"

.

2. Perform DTC confirmation procedure. Refer to 

SRC-44, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Revision: November 2015

2016 JUKE

SRC-46

< DTC/CIRCUIT DIAGNOSIS >

B0020 SIDE AIR BAG MODULE

B0020 SIDE AIR BAG MODULE

DTC Description

INFOID:0000000012199598

DTC DETECTION LOGIC

POSSIBLE CAUSE

[B0020–09, B0020–1A]

• Connection malfunction or short circuit of harness and connector

• Internal malfunction of side air bag module LH

• Internal malfunction of air bag diagnosis sensor unit

[B0020–11]

• Connection malfunction or short circuit to ground of harness and connector

• Internal malfunction of side air bag module LH

• Internal malfunction of air bag diagnosis sensor unit

[B0020–12]

• Connection malfunction or short circuit to power supply of harness and connector

• Internal malfunction of side air bag module LH

• Internal malfunction of air bag diagnosis sensor unit

[B0020–13]

• Connection malfunction or open circuit of harness and connector

• Internal malfunction of side air bag module LH

• Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-10, "On Board Diagnosis Function"

.

NOTE:

SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-46, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-45, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000012199599

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

DTC

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

B0020–09

SIDE A/B MODULE LH 
[Left Side Airbag Deployment 
Control (Subfault)]

[SHORT]

Side air bag module LH circuits are shorted to each other

B0020–11

[GND-SHORT]

Side air bag module LH circuit is shorted to ground

B0020–12

[VB-SHORT]

Side air bag module LH circuit is shorted to power supply circuit

B0020–13

[OPEN]

Side air bag module LH circuit is open

B0020–1A

[SHORT]

Side air bag module LH circuits are shorted to each other

Revision: November 2015

2016 JUKE