Content .. 572 573 574 575 ..

Nissan Juke (2016 year). Service Repair Manual - part 574

SEC-118

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

HORN FUNCTION

HORN FUNCTION

Component Function Check

INFOID:0000000012202220

CHECK FUNCTION

1. Perform “VEHICLE SECURITY HORN” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CON-

SULT.

2. Check the horn operation.

Is the operation normal?

YES

>> INSPECTION END

>> Go to

SEC-118, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000012202221

CHECK HORN FUNCTION

Check that horn functions properly using horn switch.
Do horns sound?

YES

>> GO TO 2.

>> Check horn circuit. Refer to

HRN-4, "Wiring Diagram"

CHECK HORN CONTROL CIRCUIT

1. Disconnect horn relay.

2. Disconnect IPDM E/R connector.

3. Check continuity between IPDM E/R harness connector and horn relay harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace harness.

CHECK INTERMITTENT INCIDENT

Refer to

GI-45, "Intermittent Incident"

>> INSPECTION END

Test item

Description

VEHICLE SECURITY HORN

Horn

Sounds (for 0.5 sec)

IPDM E/R

Horn relay

Continuity

Connector

Terminal

Connector

Terminal

E13

Existed

Revision: November 2015

2016 JUKE

SECURITY INDICATOR LAMP

SEC-119

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SEC

SECURITY INDICATOR LAMP

Component Function Check

INFOID:0000000012202222

CHECK FUNCTION

1. Perform “THEFT IND” in “ACTIVE TEST” mode of “IMMU” of “BCM” using CONSULT.

2. Check security indicator lamp operation.

Is the inspection result normal?

YES

>> INSPECTION END

>> Go to

SEC-119, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000012202223

CHECK FUSE

1. Turn power switch OFF.

2. Check that the following fuse in the fuse block (J/B) is not blown.

Is the fuse blown (open)?

YES

>> Replace the blown fuse after repairing the cause of blowing.

>> GO TO 2.

CHECK SECURITY INDICATOR LAMP POWER SUPPLY CIRCUIT

1. Disconnect combination meter connector.

2. Check voltage between combination meter harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace harness.

CHECK SECURITY INDICATOR LAMP SIGNAL

1. Connect combination meter connector.

2. Disconnect BCM connector.

3. Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> GO TO 5.

REPLACE BCM

Test item

Description

THEFT IND

Security indicator lamp

Illuminates

OFF

Does not illuminate

Signal name

Fuse No.

Battery power supply

11 (10 A)

(+)

(–)

Voltage (V)

(Approx.)

Combination meter

Connector

Terminal

M34

Ground

Battery voltage

(+)

(–)

Voltage (V)

(Approx.)

BCM

Connector

Terminal

M68

Ground

Battery voltage

Revision: November 2015

2016 JUKE

SEC-120

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SECURITY INDICATOR LAMP

1. Replace BCM. Refer to

BCS-94, "Removal and Installation"

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

>> INSPECTION END

CHECK SECURITY INDICATOR LAMP CIRCUIT

1. Disconnect combination meter connector.

2. Check continuity between combination meter harness connector and BCM harness connector.

3. Check continuity between combination meter harness connector and ground.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to

MWI-64, "Removal and Installation"

>> Repair or replace harness.

Combination meter

BCM

Continuity

Connector

Terminal

Connector

Terminal

M34

M68

Existed

Combination meter

Ground

Continuity

Connector

Terminal

M34

Not existed

Revision: November 2015

2016 JUKE

ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VEHICLE

SEC-121

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SEC

SYMPTOM DIAGNOSIS

ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VE-
HICLE

Description

INFOID:0000000012202224

Engine does not start when push-button ignition switch is pressed while carrying Intelligent Key.

NOTE:

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

• The engine start function, door lock function, power distribution system, and NATS-IVIS/NVIS in the Intelli-

gent Key system are closely related to each other regarding control. The vehicle security function can oper-

ate only when the door lock and power distribution systems are operating normally.

Conditions of Vehicle (Operating Conditions)

• “ENGINE START BY I-KEY”: ON

Check the setting of “ENGINE START BY I-KEY” in “Work Support” mode of “INTELLIGENT KEY” of “BCM”

using CONSULT.

• One or more of Intelligent Keys with registered Intelligent Key ID are in the vehicle.

Diagnosis Procedure

INFOID:0000000012202225

PERFORM WORK SUPPORT

Perform “INSIDE ANT DIAGNOSIS” in “Work Support” mode of “INTELLIGENT KEY” of BCM using CON-

SULT.

Refer to

DLK-28, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

>> GO TO 2.

PERFORM SELF-DIAGNOSIS RESULT

Perform Self-Diagnosis Result in “BCM”, and check whether or not DTC of inside key antenna is detected.
Is DTC detected?

YES

>> Refer to

BCS-62, "DTC Index"

>> GO TO 3.

CHECK PUSH-BUTTON IGNITION SWITCH

Check push-button ignition switch.

Refer to

PCS-78, "Component Function Check"

Is the operation normal?

YES

>> GO TO 4.

>> Repair or replace malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.
Is the inspection normal?

YES

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

>> GO TO 1.

Revision: November 2015

2016 JUKE

SEC-122

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK

SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK

Description

INFOID:0000000012202226

Security indicator lamp does not blink when ignition switch is in a position other than ON.

NOTE:

• Before performing the diagnosis, check “Work Flow”. Refer to

SEC-44, "Work Flow"

• Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-

TIONS)” before starting diagnosis, and check each symptom.

CONDITIONS OF VEHICLE (OPERATING CONDITIONS)

Power supply position is not the ON position.

Diagnosis Procedure

INFOID:0000000012202227

CHECK SECURITY INDICATOR LAMP

Check security indicator lamp.

Refer to

SEC-119, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

>> GO TO 1.

Revision: November 2015

2016 JUKE

VEHICLE SECURITY SYSTEM CANNOT BE SET

SEC-123

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SEC

VEHICLE SECURITY SYSTEM CANNOT BE SET

INTELLIGENT KEY
INTELLIGENT KEY : Description

INFOID:0000000012202228

Armed phase is not activated when all doors are locked using Intelligent Key.

NOTE:

Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-

TIONS)” before starting diagnosis, and check each symptom.

CONDITION OF VEHICLE (OPERATING CONDITIONS)

“SECURITY ALARM SET”: ON

Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using

CONSULT.

INTELLIGENT KEY : Diagnosis Procedure

INFOID:0000000012202229

CHECK INTELLIGENT KEY SYSTEM (REMOTE KEYLESS ENTRY FUNCTION)

Lock/unlock door with Intelligent Key.

Refer to

DLK-18, "REMOTE KEYLESS ENTRY FUNCTION : System Description"

Is the inspection result normal?

YES

>> GO TO 2.

>> Check Intelligent Key system (remote keyless entry function). Refer to

DLK-97, "Diagnosis Proce-

dure"

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

>> GO TO 1.

DOOR REQUEST SWITCH
DOOR REQUEST SWITCH : Description

INFOID:0000000012202230

Armed phase is not activated when all doors are locked using door request switch.

NOTE:

Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-

TIONS)” before starting diagnosis, and check each symptom.

CONDITION OF VEHICLE (OPERATING CONDITIONS)

“SECURITY ALARM SET”: ON

Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using

CONSULT.

DOOR REQUEST SWITCH : Diagnosis Procedure

INFOID:0000000012202231

CHECK INTELLIGENT KEY SYSTEM (DOOR LOCK FUNCTION)

Lock/unlock door with door request switch.

Refer to

DLK-14, "DOOR LOCK FUNCTION : System Description"

Is the inspection result normal?

YES

>> GO TO 2.

>> Check Intelligent Key system (door lock function). Refer to

DLK-93, "ALL DOOR REQUEST

SWITCHES : Diagnosis Procedure"

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

Revision: November 2015

2016 JUKE

SEC-124

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

VEHICLE SECURITY SYSTEM CANNOT BE SET

>> GO TO 1.

DOOR KEY CYLINDER
DOOR KEY CYLINDER : Description

INFOID:0000000012202232

ARMED phase is not activated when all doors are locked using mechanical key.

NOTE:

Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check

each symptom.

CONDITION OF VEHICLE (OPERATING CONDITION)

• SECURITY ALARM SET: ON

Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using

CONSULT.

DOOR KEY CYLINDER : Diagnosis Procedure

INFOID:0000000012202233

CHECK POWER DOOR LOCK SYSTEM

Lock or unlock doors using mechanical key.

Refer to

DLK-11, "System Description"

Is the inspection result normal?

YES

>> GO TO 2.

>> Check power door lock system. Refer to

DLK-96, "Diagnosis Procedure"

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

>> GO TO 1.

DOOR LOCK AND UNLOCK SWITCH
DOOR LOCK AND UNLOCK SWITCH : Description

INFOID:0000000012202234

Armed phase is not activated when all doors are locked by door lock and unlock switch.

NOTE:

Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-

TIONS)” before starting diagnosis, and check each symptom.

CONDITION OF VEHICLE (OPERATING CONDITIONS)

“SECURITY ALARM SET”: ON

Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using

CONSULT.

DOOR LOCK AND UNLOCK SWITCH : Diagnosis Procedure

INFOID:0000000012202235

CHECK DOOR LOCK FUNCTION

Lock/unlock door using mechanical key inserted into door key cylinder.

Refer to

DLK-11, "System Description"

Is the inspection result normal?

YES

>> GO TO 2.

>> Check Intelligent Key system (remote keyless entry function). Refer to

DLK-90, "ALL DOOR :

Diagnosis Procedure"

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

>> GO TO 1.

Revision: November 2015

2016 JUKE

VEHICLE SECURITY ALARM DOES NOT ACTIVATE

SEC-125

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SEC

VEHICLE SECURITY ALARM DOES NOT ACTIVATE

Description

INFOID:0000000012202236

Alarm does not operate when alarm operating condition is satisfied.

NOTE:

Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-

TIONS)” before starting diagnosis, and check each symptom.

CONDITION OF VEHICLE (OPERATING CONDITIONS)

“SECURITY ALARM SET”: ON

Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using

CONSULT.

Diagnosis Procedure

INFOID:0000000012202237

CHECK DOOR SWITCH

Check door switch.

Refer to

DLK-77, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace the malfunctioning door switch

CHECK HEADLAMPS FUNCTION

Check head lamps function.

Refer to

SEC-117, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunctioning parts.

CHECK HORN FUNCTION

Check horn function.

Refer to

SEC-118, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

>> GO TO 1.

Revision: November 2015

2016 JUKE

Content .. 572 573 574 575 ..