Nissan Juke (2016 year). Service Repair Manual - part 571

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     569      570      571      572     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 571

 

 

SEC-94

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B26F8 BCM

B26F8 BCM

DTC Logic

INFOID:0000000012202192

DTC DETECTION LOGIC

NOTE:

DTC B26F8 can be detected even though the related circuit is not used in this vehicle.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON and wait 1 second.

2. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-94, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012202193

1.

INSPECTION START

1. Turn ignition switch ON.

2. Select “Self Diagnostic Result” mode of ”BCM” using CONSULT.

3. Touch “ERASE”.

4. Perform DTC CONFIRMATION PROCEDURE for DTC B26F8.

Refer to 

SEC-94, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 2.

NO

>> INSPECTION END

2.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B26F8

BCM

Starter control replay control signal and feedback circuit 
signal (inside BCM) does not match.

BCM

Revision: November 2015

2016 JUKE

B26F9 CRANKING REQUEST CIRCUIT

SEC-95

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B26F9 CRANKING REQUEST CIRCUIT

DTC Logic

INFOID:0000000012202194

DTC DETECTION LOGIC

NOTE:

• If DTC B26F9 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-83, "DTC Logic"

.

• If DTC B26F9 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-84, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION

1. Perform DTC CONFIRMATION PROCEDURE for DTC P1650. Refer to 

EC-492, "DTC Logic"

.

2. Turn ignition switch ON.

3. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-95, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012202195

1.

CHECK CRANKING REQUEST SIGNAL

1. Turn ignition switch ON.

2. Check voltage between BCM harness connector and ground under the following conditions.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK CRANKING REQUEST SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connector.

3. Disconnect ECM connector.

4. Check continuity between BCM harness connector and ECM harness connector.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B26F9

CRANK REQ CIR SHORT

BCM detects that the status of the following 
signals does not match.
• Cranking request signal from ECM
• Starter control relay control signal from 

ECM (CAN)

• Harness or connectors 

(CAN communication line is open or 
shorted.)

• Harness or connectors 

(Cranking request signal circuit is open 
or shorted.)

• ECM
• BCM

(+)

(–)

Condition

Voltage (V)

(Approx.)

BCM

Connector

Terminal

M69

64

Ground

Ignition switch OFF

3.6

Ignition switch ON

• Engine: Stopped
• Selector lever position: P

0

• Engine: Stopped
• Selector lever position: 

Other than P

12

Engine running

12

Revision: November 2015

2016 JUKE

SEC-96

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B26F9 CRANKING REQUEST CIRCUIT

5. Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

3. Perform DTC CONFIRMATION PROCEDURE for DTC B26F9. Refer to 

SEC-95, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE ECM

Replace ECM.

Refer to 

EC-590, "Removal and Installation"

.

>> INSPECTION END

BCM

ECM

Continuity

Connector

Terminal

Connector

Terminal

M69

64

F26

92

Existed

BCM

Ground

Continuity

Connector

Terminal

M69

64

Not existed

Revision: November 2015

2016 JUKE

B26FA CRANKING REQUEST CIRCUIT

SEC-97

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B26FA CRANKING REQUEST CIRCUIT

DTC Logic

INFOID:0000000012202196

DTC DETECTION LOGIC

NOTE:

• If DTC B26FA is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-83, "DTC Logic"

.

• If DTC B26FA is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-84, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION

1. Perform DTC CONFIRMATION PROCEDURE for DTC P1650. Refer to 

EC-492, "DTC Logic"

.

2. Turn ignition switch ON.

3. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT. 
Is DTC detected?

YES

>> Go to 

SEC-97, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012202197

1.

CHECK CRANKING REQUEST SIGNAL

1. Turn ignition switch ON.

2. Check voltage between BCM harness connector and ground under the following conditions.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK CRANKING REQUEST SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connector.

3. Disconnect ECM connector.

4. Check continuity between BCM harness connector and ECM harness connector.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B26FA

CRANK REQ CIR OPEN

BCM detects that the status of the following 
signals does not match.
• Cranking request signal from ECM
• Starter control relay control signal from 

ECM (CAN)

• Harness or connectors 

(CAN communication line is open or 
shorted.)

• Harness or connectors 

(Cranking request signal circuit is open 
or shorted.)

• BCM
• ECM

(+)

(–)

Condition

Voltage (V)

(Approx.)

BCM

Connector

Terminal

M69

64

Ground

Ignition switch OFF

3.6

Ignition switch ON

• Engine: Stopped
• Selector lever position: P

0

• Engine: Stopped
• Selector lever position: 

Other than P

12

Engine running

12

Revision: November 2015

2016 JUKE

SEC-98

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B26FA CRANKING REQUEST CIRCUIT

5. Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

REPLACE BCM

1. Replace BCM. Refer to 

EC-590, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

3. Perform DTC CONFIRMATION PROCEDURE for DTC B26FA. Refer to 

SEC-97, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE ECM

Replace ECM.

Refer to 

EC-590, "Removal and Installation"

.

>> INSPECTION END

BCM

ECM

Continuity

Connector

Terminal

Connector

Terminal

M69

64

F26

92

Existed

BCM

Ground

Continuity

Connector

Terminal

M69

64

Not existed

Revision: November 2015

2016 JUKE

B26FB CLUTCH SWITCH

SEC-99

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B26FB CLUTCH SWITCH

DTC Logic

INFOID:0000000012202198

DTC DETECTION LOGIC

NOTE:

• If DTC B26FB is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-83, "DTC Logic"

.

• If DTC B26FB is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-84, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?

YES >> Go 

to 

SEC-99, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012202199

1.

INSPECTION START

1. Turn ignition switch ON.

2. Select “Self diagnostic result” mode of BCM using CONSULT.

3. Touch “ERASE”.

4. Perform DTC CONFIRMATION PROCEDURE for DTC B26FB. Refer to 

SEC-99, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 2.

NO

>> INSPECTION END

2.

CHECK CLUTCH PEDAL POSITION SWITCH CIRCUIT

Refer to 

EC-572, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detection condition

Possible cause

B26FB

CLUTCH SW

BCM receives the abnormal signal of clutch 
pedal position switch from ECM via CAN 
communication.

• Harness or connector

(CAN communication line is open or 
shorted)
(Clutch pedal position switch circuit 
is open or shorted.)

Revision: November 2015

2016 JUKE

SEC-100

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B26FC KEY REGISTRATION

B26FC KEY REGISTRATION

DTC Logic

INFOID:0000000012202200

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

2. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-100, "Diagnosis Procedure"

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012202201

1.

REPLACE INTELLIGENT KEY

1. Prepare Intelligent Key that matches the vehicle.

2. Perform initialization of BCM and registration of Intelligent Key using CONSULT.

3. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?

YES

>> GO TO 2.

NO

>> INSPECTION END

2.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B26FC

KEY REGISTRATION

Intelligent Key that does not match the vehicle is 
registered.

• Improper registration operation
• Intelligent Key
• BCM

Revision: November 2015

2016 JUKE

B209F CRANKING REQUEST CIRCUIT

SEC-101

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B209F CRANKING REQUEST CIRCUIT

DTC Logic

INFOID:0000000012202202

DTC DETECTION LOGIC

NOTE:

If DTC B209F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to 

PCS-

31, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Perform DTC CONFIRMATION PROCEDURE for DTC P1650. Refer to 

EC-492, "DTC Logic"

.

2. Turn ignition switch ON.

3. Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?

YES

>> Refer to 

SEC-101, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012202203

1.

CHECK CRANKING REQUEST SIGNAL

1. Turn ignition switch ON.

2. Check voltage between IPDM E/R harness connector and ground under the following conditions.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK CRANKING REQUEST SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Disconnect ECM connector.

4. Check continuity between IPDM E/R harness connector and ECM harness connector.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B209F

CRANK REQ CIR OPEN 

When the following items do not match, a 
malfunction is detected.
• Cranking request signal from ECM
• Starter control relay control signal from 

ECM (CAN)

• Harness or connectors

(CAN communication line is open or 
shorted.)

• Harness or connectors

(Cranking request signal circuit is open 
or shorted.)

• IPDM  E/R
• ECM

(+)

(–)

Condition

Voltage (V)

(Approx.)

IPDM E/R

Connector

Terminal

E13

23

Ground

Ignition switch OFF

3.6

Ignition switch ON

• Engine: Stopped
• Selector lever position: P

0

• Engine: Stopped
• Selector lever position: 

Other than P

12

Engine running

12

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     569      570      571      572     ..