Nissan Juke (2016 year). Service Repair Manual - part 542

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     540      541      542      543     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 542

 

 

RF-4

< PRECAUTION >

PRECAUTIONS

(Turning it ON outside the lamp case may cause fire or visual impairments.)

• Never touch the bulb glass immediately after turning it OFF. It is extremely hot. 

CAUTION:

Comply with the following cautions to prevent any error and malfunction.

• Install the xenon bulb securely. (Insufficient bulb socket installation may melt the bulb, the connec-

tor, the housing, etc. by high-voltage leakage or corona discharge.)

• Never perform HID circuit inspection with a tester.

• Never touch the xenon bulb glass with hands. Never put oil and grease on it.

• Dispose of the used xenon bulb after packing it in thick vinyl without breaking it. 

• Never wipe out dirt and contamination with organic solvent (thinner, gasoline, etc.).

Precautions for Removing Battery Terminal

INFOID:0000000012964841

When disconnecting the battery terminal, pay attention to the following.

• Always use a 12V battery as power source.

• Never disconnect battery terminal while engine is running.

• When removing the 12V battery terminal, turn OFF the ignition

switch and wait at least 30 seconds.

• For vehicles with the engine listed below, remove the battery termi-

nal after a lapse of the specified time:

NOTE:

ECU may be active for several tens of seconds after the ignition switch is turned OFF. If the battery terminal

is removed before ECU stops, then a DTC detection error or ECU data corruption may occur.

• After high-load driving, if the vehicle is equipped with the V9X engine, turn the ignition switch OFF and wait

for at least 15 minutes to remove the battery terminal.

NOTE:

• Turbocharger cooling pump may operate in a few minutes after the ignition switch is turned OFF.

• Example of high-load driving

- Driving for 30 minutes or more at 140 km/h (86 MPH) or more.

- Driving for 30 minutes or more on a steep slope.

• For vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON

the ignition switch.

NOTE:

If the ignition switch is turned ON with any one of the terminals of main battery and sub battery discon-

nected, then DTC may be detected.

• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.

NOTE:

The removal of 12V battery may cause a DTC detection error.

D4D engine

: 20 minutes

YS23DDT

: 4 minutes

HRA2DDT

: 12 minutes

YS23DDTT

: 4 minutes

K9K engine

: 4 minutes

ZD30DDTi

: 60 seconds

M9R engine

: 4 minutes

ZD30DDTT

: 60 seconds

R9M engine

: 4 minutes

V9X engine

: 4 minutes

YD25DDTi

: 2 minutes

SEF289H

Revision: November 2015

2016 JUKE

PREPARATION

RF-5

< PREPARATION >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

PREPARATION

PREPARATION

Special Service Tool

INFOID:0000000012196953

The actual shapes of TechMate tools may differ from those of special service tools illustrated here.

Commercial Service Tool

INFOID:0000000012196954

Tool number

(TechMate No.)

Tool name

Description

(J-39570)
Chassis ear

Locates the noise

(J-50397)
NISSAN Squeak and Rattle Kit

Repairs the cause of noise

SIIA0993E

SIIA0994E

Tool name

Description

Engine ear

Locates the noise

Remover tool

Removes the clips, pawls and metal clips

SIIA0995E

JMKIA3050ZZ

Revision: November 2015

2016 JUKE

RF-6

< SYSTEM DESCRIPTION >

COMPONENT PARTS

SYSTEM DESCRIPTION

COMPONENT PARTS

Component Parts Location

INFOID:0000000012196955

Component Description

INFOID:0000000012196956

JMKIA5998ZZ

1.

Sunroof motor assembly

2.

Sunroof switch

3.

Combination meter

4.

BCM
Refer to 

BCS-5, "BODY CONTROL 

SYSTEM : Component Parts Loca-
tion"

.

5.

Front door switch

A.

View with headlining removed

Component

Function

BCM

Supplies the power supply to sunroof motor assembly.

Combination meter

Transmits vehicle speed signal to sunroof motor assembly.

Front door switch

Detects door open/close condition and transmits to BCM.

Sunroof motor assembly

It is sunroof motor and CPU integrated type that enables tilt up/down & slide open/close by sun-
roof switch operation.

Sunroof switch

Transmits tilt up/down & slides open/close operation signal to sunroof motor assembly.

Revision: November 2015

2016 JUKE

SYSTEM

RF-7

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

SYSTEM

System Diagram

INFOID:0000000012196957

SUNROOF

System Description

INFOID:0000000012196958

SUNROOF SYSTEM

• Sunroof motor assembly operates with the power supply that is output from BCM while ignition switch is ON

or retained power is operating.

• Tilt up/down & slide open/close signals from sunroof switch enables operate sunroof motor to move arbi-

trarily.

• Sunroof motor assembly receives a vehicle speed signal from combination meter and controls the sunroof

motor operation.

OPERATION DESCRIPTION

The sunroof operate to the following condition by the sunroof switch operation.

JMKIA5324GB

Sunroof position before operation

Switch operation

Sunroof action

Sunroof position after operation

Tilt up

A: Glass lid
B: Roof panel

Close

Not action

Open

Close

Fully-closed

JMKIA5777ZZ

JMKIA5869ZZ

Revision: November 2015

2016 JUKE

RF-8

< SYSTEM DESCRIPTION >

SYSTEM

Tilt halfway-open

A: Glass lid
B: Roof panel

Close

Tilt up

Tilt up

Open

Close

Fully-closed

Fully-closed

A: Glass lid
B: Roof panel

Close

Tilt up

Tilt up

Open

Open

Fully-open

Halfway-open

A: Glass lid
B: Roof panel

Close

Close

Fully-closed

Open

Open

Fully-open

Fully-open

A: Glass lid
B: Roof panel

Close

Close

Fully-closed

Open

Not action

Sunroof position before operation

Switch operation

Sunroof action

Sunroof position after operation

JMKIA5778ZZ

JMKIA5870ZZ

JMKIA5869ZZ

JMKIA5779ZZ

JMKIA5870ZZ

JMKIA5871ZZ

JMKIA5780ZZ

JMKIA5872ZZ

JMKIA5871ZZ

JMKIA5781ZZ

JMKIA5872ZZ

Revision: November 2015

2016 JUKE

SYSTEM

RF-9

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

AUTO OPERATION

Sunroof AUTO feature makes it possible to slide open and slide close or tilt up and tilt down the sunroof with-

out holding the sunroof switch in the slide open/tilt down or slide close/tilt up position.

RETAINED POWER OPERATION 

Retained power operation is an additional power supply function that enables sunroof system to operate dur-

ing 45 seconds even when ignition switch is turned OFF.

RETAINED POWER FUNCTION CANCEL CONDITIONS 

• Front door CLOSE (door switch OFF)

OPEN (door switch ON).

• When ignition switch is ON again.

• When timer time passes. (45 seconds)

ANTI-PINCH FUNCTION

The CPU of sunroof motor assembly monitors the sunroof motor operation and the sunroof position (fully-

closed or other) by the signals from sunroof motor.

When sunroof motor detects an interruption during the following slide close and tilt down operation, sunroof

switch controls the motor for open and the sunroof will operate until full up position (when tilt down operate) or

150 mm (5.91 in) or more in an open direction (when slide close operate).

Revision: November 2015

2016 JUKE

RF-10

< ECU DIAGNOSIS INFORMATION >

BCM (BODY CONTROL MODULE)

ECU DIAGNOSIS INFORMATION

BCM (BODY CONTROL MODULE)

List of ECU Reference

INFOID:0000000012196959

ECU

Reference

BCM

BCS-39, "Reference Value"

BCS-60, "Fail-safe"

BCS-61, "DTC Inspection Priority Chart"

BCS-62, "DTC Index"

Revision: November 2015

2016 JUKE

SUNROOF SYSTEM

RF-11

< ECU DIAGNOSIS INFORMATION >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

SUNROOF SYSTEM

Reference Value

INFOID:0000000012196960

TERMINAL LAYOUT

PHYSICAL VALUES

JMKIA2225ZZ

Terminal No.

(Wire color)

Description

Condition

Voltage (V)

(Approx.)

+

Signal name

Input/

Output

1

(B)

Ground Ground

3

(L)

Ground Retained power signal

Input

Ignition switch ON

Battery voltage

Within 45 second after ignition 
switch is turned to OFF

When driver side or passenger side 
door is opened during retained pow-
er operation

0

5

(Y)

Ground Sunroof open signal

Input

Sunroof switch: Open

0  

Ignition switch ON

Battery voltage

6

(P)

Ground Sunroof power supply 

Input

Battery voltage

8

(V)

Ground

Vehicle speed signal (8-
pulse)

Input

Speedometer operated [When vehi-
cle speed is approx.40km/ h 
(25MPH)]

10

(G)

Ground Sunroof close signal

Input

Sunroof switch: Close

0  

Ignition switch ON

Battery voltage

JSNIA0012GB

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     540      541      542      543     ..