Content .. 538 539 540 541 ..

Nissan Juke (2016 year). Service Repair Manual - part 540

RAX-14

< PERIODIC MAINTENANCE >

[AWD]

REAR WHEEL HUB AND HOUSING

PERIODIC MAINTENANCE

REAR WHEEL HUB AND HOUSING

Inspection

INFOID:0000000012196559

COMPONENT PART

Check the mounting conditions (looseness, back lash) of each component and component conditions (wear,

damage) are normal.

WHEEL HUB ASSEMBLY (BEARING-INTEGRATED TYPE)

Check the following items, and replace the part it necessary.

• Move wheel hub assembly in the axial direction by hand. Check there is no looseness of wheel bearing.

• Rotate wheel hub assembly and check there is no unusual noise or other irregular conditions. If there is any

of irregular conditions, replace wheel hub assembly.

Axial end play

: Refer to

RAX-26, "Wheel Bearing"

Revision: November 2015

2016 JUKE

REAR DRIVE SHAFT

RAX-15

< PERIODIC MAINTENANCE >

[AWD]

RAX

REAR DRIVE SHAFT

Inspection

INFOID:0000000012196560

• Check drive shaft mounting point and joint for looseness and other damage.

• Check boot for cracks and other damage.

CAUTION:

Replace entire drive shaft assembly when noise or vibration occur from drive shaft.

Revision: November 2015

2016 JUKE

RAX-16

< REMOVAL AND INSTALLATION >

[AWD]

REAR WHEEL HUB AND HOUSING

REMOVAL AND INSTALLATION

REAR WHEEL HUB AND HOUSING

Exploded View

INFOID:0000000012196561

Removal and Installation

INFOID:0000000012196562

REMOVAL

1. Remove tires with power tool. Refer to

WT-39, "Removal and Installation"

2. Remove wheel sensor. Refer to

BRC-150, "REAR WHEEL SENSOR : Removal and Installation"

3. Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to

BR-64, "BRAKE CALIPER ASSEMBLY : Removal and Installation"

CAUTION:

Never depress brake pedal while brake caliper is removed.

4. Remove disc rotor. If disc rotor cannot be removed, remove as follows.

CAUTION:

• Parking brake completely in the released position.

• Put matching marks (A) on the wheel hub assembly and

the disc rotor before removing the disc rotor.

• Never drop disc rotor.

a. Fix the disc rotor with wheel nuts and remove the adjusting hole

plug.

Axle housing

Suspension arm

Parking brake assembly

Hub bolt

Wheel hub assembly (Bearing-inte-
grated type)

Disc rotor

Plug

Wheel hub lock nut

Cotter pin

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JPDIG0202GB

JPDIG0066ZZ

Revision: November 2015

2016 JUKE

REAR WHEEL HUB AND HOUSING

RAX-17

< REMOVAL AND INSTALLATION >

[AWD]

RAX

b. Using suitable tool, rotate adjuster (1) in the direction (A) to

retract and loosen brake shoe.

c. Remove disc rotor.
5. Remove cotter pin, and then loosen wheel hub lock nut with

power tool.

6. Patch wheel hub lock nut with a piece of wood. Hammer the

wood to disengage wheel hub assembly from drive shaft.

CAUTION:

• Never place drive shaft joint at an extreme angle. Also be

careful not to overextend slide joint.

• Never allow drive shaft to hang down without support for

joint sub-assembly, shaft and the other parts.

NOTE:

Use suitable puller, if wheel hub assembly and drive shaft can-

not be separated even after performing the above procedure.

7. Remove wheel hub lock nut.
8. Remove wheel hub assembly.

CAUTION:

Never remove parking brake assembly. Protect it from falling.

9. If axle housing need to be removed, remove drive shaft. Refer to

RAX-19, "Removal and Installation"

10. Remove hub bolts (1) from wheel hub assembly, using the ball

joint remover (A) (commercial service tool).

CAUTION:

• Remove hub bolt only when necessary.

• Never hammer the hub bolt to avoid impact to the wheel

hub assembly.

• Pull out the hub bolt in a direction perpendicular to the

wheel hub assembly.

11. Perform inspection after removal. Refer to

RAX-17, "Inspection"

INSTALLATION

Note the following, and install in the reverse order of the removal.

• Place a washer (A) as shown in the figure to install the hub bolts

(1) by using the tightening force of the nut (B).

CAUTION:

• Check that there is no clearance between wheel hub assem-

bly and hub bolt.

• Never reuse hub bolt.

• Never reuse wheel hub lock nut and cotter pin.

• Align the matching marks that have been made during removal

when reusing the disc rotor.

• Perform inspection after installation. Refer to

RAX-17, "Inspection"

Inspection

INFOID:0000000012196563

INSPECTION AFTER REMOVAL

Check wheel hub assembly for wear, cracks, and damage. Replace if necessary.

INSPECTION AFTER INSTALLATION

JPDIG0204ZZ

JPDIG0070ZZ

JPDIF0299ZZ

JPDIF0300ZZ

Revision: November 2015

2016 JUKE

RAX-18

< REMOVAL AND INSTALLATION >

[AWD]

REAR WHEEL HUB AND HOUSING

1. Check wheel sensor harness for proper connection.

BRC-148, "REAR WHEEL SENSOR : Exploded

View"

2. Adjust parking brake operation (stroke). Refer to

PB-4, "Inspection and Adjustment"

3. Check wheel alignment. Refer to

RSU-7, "Inspection"

4. Adjust neutral position of steering angle sensor. Refer to

BRC-63, "Work Procedure"

Revision: November 2015

2016 JUKE

REAR DRIVE SHAFT

RAX-19

< REMOVAL AND INSTALLATION >

[AWD]

RAX

REAR DRIVE SHAFT

Exploded View

INFOID:0000000012196564

Removal and Installation

INFOID:0000000012196565

REMOVAL

1. Remove tires with power tool. Refer to

WT-39, "Removal and Installation"

2. Remove wheel sensor. Refer to

BRC-150, "REAR WHEEL SENSOR : Removal and Installation"

3. Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to

BR-64, "BRAKE CALIPER ASSEMBLY : Removal and Installation"

CAUTION:

Never depress brake pedal while brake caliper is removed.

4. Remove disc rotor. Refer to

RAX-16, "Removal and Installation"

5. Remove cotter pin, and then loosen wheel hub lock nut with power tool. Refer to

RAX-16, "Removal and

Installation"

6. Patch wheel hub lock nut with a piece of wood. Hammer the

wood to disengage wheel hub assembly from drive shaft.

CAUTION:

• Never place drive shaft joint at an extreme angle. Also be

careful not to overextend slide joint.

• Never allow drive shaft to hang down without support for

joint sub-assembly, shaft and the other parts.

NOTE:

Use suitable puller, if wheel hub assembly and drive shaft can-

not be separated even after performing the above procedure.

7. Remove wheel hub lock nut.
8. Set jack under suspension arm.

Circular clip

Dust shield

Housing

Snap ring

Ball cage/steel ball/inner race as-
sembly

Stopper ring

Boot band

Boot

Shaft

10. Joint sub-assembly

11. Sensor rotor

: Wheel side

: Fill NISSAN genuine grease or an equivalent.

: Always replace after every disassembly.

JPDIG0207ZZ

JPDIG0070ZZ

Revision: November 2015

2016 JUKE

RAX-20

< REMOVAL AND INSTALLATION >

[AWD]

REAR DRIVE SHAFT

CAUTION:

• Never damage the suspension arm with a jack.

• Check the stable condition when using a jack.

9. Remove stabilizer link. Refer to

RSU-35, "Removal and Installation"

10. Remove shock absorber from suspension arm. Refer to

RSU-24, "Removal and Installation"

11. Remove upper link from suspension arm. Refer to

RSU-33, "Removal and Installation"

12. Remove lower link from suspension arm. Refer to

RSU-31, "Removal and Installation"

13. Remove drive shaft from final drive assembly.

CAUTION:

Confirm that the circular clip is attached to the drive shaft.

14. Perform inspection after removal. Refer to

RAX-25, "Inspection"

INSTALLATION

Note the following, and install in the reverse order of removal.

• Place the protector (A) [SST:KV38107900 ( — )] onto final drive

assembly to prevent damage to the oil seal while inserting drive

shaft. Slide drive shaft sliding joint and tap with a hammer to install

securely.

CAUTION:

Check that circular clip is completely engaged.

• Perform final tightening of bolts and nuts at suspension arm (rub-

ber bushing), under unladen conditions with tires on level ground.

• Perform inspection after installation. Refer to

RAX-25, "Inspection"

WHEEL SIDE
WHEEL SIDE : Disassembly and Assembly

INFOID:0000000012196566

DISASSEMBLY

1. Fix shaft with a vise.

CAUTION:

Protect shaft using aluminum or copper plates when fixing with a vise.

2. If sensor rotor needs to be removed, use a bearing replacer (A)

and puller (B).

3. Remove boot bands. Then remove boot from joint sub-assem-

bly.

4. Screw drive shaft puller (A) (commercial service tool) into joint

sub-assembly screw part to a length of 30 mm (1.18 in) or more.

Support drive shaft with one hand and pull out joint sub-assem-

bly from shaft.

CAUTION:

• Align drive shaft puller and drive shaft and remove them

by pulling firmly and uniformly.

• If joint sub-assembly cannot be removed after five or

more unsuccessful attempts, replace shaft and joint sub

assembly as a set.

5. Remove circular clip from shaft.
6. Remove boot from shaft.

JPDIF0023ZZ

JPDIG0016ZZ

JPDIG0151ZZ

Revision: November 2015

2016 JUKE

REAR DRIVE SHAFT

RAX-21

< REMOVAL AND INSTALLATION >

[AWD]

RAX

7. Perform inspection after disassembly. Refer to

RAX-25, "Inspection"

ASSEMBLY

1. If sensor rotor (1) is removed, use a drift (A) [SST:KV38100500 (

— )] and color (B) [SST:KV40101840 ( — )] to press in a new

one.

CAUTION:

Never reuse sensor rotor.

2. Clean the old grease on joint sub-assembly with paper waste.

3. Fill serration slot joint sub-assembly (1) with NISSAN genuine

grease or equivalent until the serration slot and ball groove

become full to the brim.

CAUTION:

After applying grease, use a shop cloth to wipe off old

grease that has oozed out.

4. Install boot and boot bands to shaft.

CAUTION:

• Wrap serration on shaft with tape (A) to protect the boot

from damage.

• Never reuse boot and boot band.

5. Remove the tape wrapped around the serrated on shaft.

6. Position the circular clip (1) on groove at the shaft edge.

CAUTION:

Never reuse circular clip.

NOTE:

Drive joint inserter is recommended when installing circular clip.

7. Align both center axles of the shaft edge and joint sub-assembly.

Then assemble shaft with joint sub-assembly holding circular

clip.

PDIA1182J

JPDIF0008ZZ

JPDIF0009ZZ

JPDIF0305ZZ

Revision: November 2015

2016 JUKE

Content .. 538 539 540 541 ..