Nissan Juke (2016 year). Service Repair Manual - part 510

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     508      509      510      511     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 510

 

 

PCS-26

< WIRING DIAGRAM >

[IPDM E/R]

IPDM E/R

WIRING DIAGRAM

IPDM E/R

Wiring Diagram

INFOID:0000000012197163

JRMWI5132GB

Revision: November 2015

2016 JUKE

PCS

IPDM E/R

PCS-27

< WIRING DIAGRAM >

[IPDM E/R]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

JRMWI5133GB

Revision: November 2015

2016 JUKE

PCS-28

< WIRING DIAGRAM >

[IPDM E/R]

IPDM E/R

JRMWI5134GB

Revision: November 2015

2016 JUKE

PCS

IPDM E/R

PCS-29

< WIRING DIAGRAM >

[IPDM E/R]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

JRMWI5135GB

Revision: November 2015

2016 JUKE

PCS-30

< WIRING DIAGRAM >

[IPDM E/R]

IPDM E/R

JRMWI5136GB

Revision: November 2015

2016 JUKE

PCS

U1000 CAN COMM CIRCUIT

PCS-31

< DTC/CIRCUIT DIAGNOSIS >

[IPDM E/R]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

DTC/CIRCUIT DIAGNOSIS

U1000 CAN COMM CIRCUIT

Description

INFOID:0000000012197164

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-

tiplex communication line with high data communication speed and excellent error detection ability. Modern

vehicle is equipped with many electronic control unit, and each control unit shares information and links with

other control units during operation (not independent). In CAN communication, control units are connected

with 2 communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less

wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to 

LAN-30, "CAN COMMUNICATION SYSTEM : CAN Communica-

tion Signal Chart"

.

DTC Logic

INFOID:0000000012197165

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000012197166

1.

PERFORM SELF DIAGNOSTIC

1. Turn the ignition switch ON and wait for 2 seconds or more.

2. Check “Self Diagnostic Result” of IPDM E/R.
Is DTC “U1000” displayed?

YES

>> Refer to 

LAN-17, "Trouble Diagnosis Flow Chart"

.

NO

>> Refer to 

GI-45, "Intermittent Incident"

.

DTC

CONSULT display de-

scription

DTC Detection Condition

Possible cause

U1000

CAN COMM CIRCUIT

When IPDM E/R cannot communicate CAN communi-
cation signal continuously for 2 seconds or more

CAN communication system

Revision: November 2015

2016 JUKE

PCS-32

< DTC/CIRCUIT DIAGNOSIS >

[IPDM E/R]

B2098 IGNITION RELAY ON STUCK

B2098 IGNITION RELAY ON STUCK

Description

INFOID:0000000012197167

• IPDM E/R operates the ignition relay when it receives an ignition switch ON signal from BCM via CAN com-

munication.

• Turn the ignition relay OFF by pressing the push-button ignition switch once when the vehicle speed is 4 km/

h (2.5 MPH) or less.

• Turn the ignition relay OFF with the following operation when the vehicle speed is more than 4 km/h (2.5

MPH) or when an abnormal condition occurs in CAN communication from the combination meter (Emer-

gency OFF)

- Press and hold the push-button ignition switch for 2 seconds or more.

- Press the push-button ignition switch 3 times within 1.5 seconds.

NOTE:

The ignition relay does not turn ON for 3 seconds after emergency OFF even if the push-button ignition switch

is pressed.

DTC Logic

INFOID:0000000012197168

DTC DETECTION LOGIC

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?

YES

>> Refer to 

PCS-32, "Diagnosis Procedure"

.

NO

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000012197169

1.

CHECK SELF DIAGNOSTIC RESULT

Check DTC using CONSULT.
What is the display history of DTC “B2098”?

“CRNT”>> GO TO 2.

“PAST” >> GO TO 5.

2.

CHECK IGNITION RELAY CONTROL CIRCUIT VOLTAGE 1

1. Turn ignition switch ON

2. Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 3.

3.

CHECK IGNITION RELAY CONTROL CIRCUIT VOLTAGE 2

1. Disconnect IPDM E/R connector.

2. Turn ignition switch ON

DTC

CONSULT display 

description

DTC Detection Condition

Possible causes

B2098

IGN RELAY ON 
CIRC

The ignition relay ON is detected for 1 second at ignition switch OFF
(CPU monitors the status at the contact and excitation coil circuits 
of the ignition relay inside it)

Ignition relay malfunction

(+)

(–)

Voltage

(Approx.)

IPDM E/R

Connector

Terminal

E17

68

Ground

0 V

Revision: November 2015

2016 JUKE

PCS

B2098 IGNITION RELAY ON STUCK

PCS-33

< DTC/CIRCUIT DIAGNOSIS >

[IPDM E/R]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

3. Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

NO

>> Check the harness of the ignition relay control circuit for a short to power.

4.

CHECK IGNITION RELAY CONTROL CIRCUIT

1. Disconnect IPDM E/R connector.

2. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Perform the diagnosis procedure for DTC B26F2. Refer to 

PCS-75, "DTC Logic"

.

NO

>> Repair or replace harness.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> INSPECTION END

(+)

(–)

Voltage

(Approx.)

IPDM E/R

Connector

Terminal

E17

68

Ground

0 V

IPDM E/R

Ground

Continuity

Connector

Terminal

E17

68

Not existed

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     508      509      510      511     ..