Content .. 454 455 456 457 ..

Nissan Juke (2016 year). Service Repair Manual - part 456

IP-14

< REMOVAL AND INSTALLATION >

INSTRUMENT PANEL ASSEMBLY

[]: Number indicates step in removal procedure.

WARNING:

Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or

more.

REMOVAL

CAUTION:

When removing, always use a remover tool that is made of plastic.

1. Remove shift lever knob (MT models only). Refer to

TM-25, "Removal and Installation"

(6MT: RS6F94R)

TM-83, "Removal and Installation"

(6MT: RS6F52H).

2. Remove console finisher assembly.

1. Put selector lever in “N” position.

2. Loosen the parking brake lever stroke by turning the adjusting nut with a socket wrench. Refer to

PB-

4, "Inspection and Adjustment"

3. Lift up console finisher assembly in numerical order shown in the figure and disengage metal clips.

4. Remove console finisher assembly while pulling it towards vehicle rear.

Cluster lid A

[17]

[2]

Combination meter

[18]

[3]

Multi display unit (with auto A/C) or A/C finisher
(with manual A/C)

[19]

[1]

A/C control fixing screws (with manual A/C)

[20]

Cluster lid C

[21]

[2]

Audio unit or AV C/U

[22]

[3]

Harness connector of hazard switch

[23]

Cluster tray

[24]

Front body side welt RH

[25]

Front pillar garnish RH

[26]

Instrument side finisher RH

[27]

Glove box lid

[28]

Glove box assembly

[29]

Passenger air bag module

[30]

Switch panel

[31]

Instrument panel assembly

[32]

Revision: November 2015

2016 JUKE

INSTRUMENT PANEL ASSEMBLY

IP-15

< REMOVAL AND INSTALLATION >

CAUTION:

• Be careful not for damaging parts in surrounding area.

• Remove metal clips slowly so that they are not damaged.

5. Disconnect seat heated switch harness connectors (with seat heated switch).

3. Remove console rear finisher.

1. Put front seat assembly (LH and RH) to frontmost position.

2. Pull back console rear finisher, and disengage the pawls

and metal clips.

4. Remove center console assembly fixing screws (A).

5. Remove instrument lower cover LH.

1. Put front seat assembly LH to rearmost position.

: Metal clip

JSJIA0057ZZ

: Pawl

: Metal clip

JMJIA4183ZZ

JMJIA4202ZZ

Revision: November 2015

2016 JUKE

IP-16

< REMOVAL AND INSTALLATION >

INSTRUMENT PANEL ASSEMBLY

2. Remove fixing clip (A).

3. Pull the instrument lower cover LH crosswise, and disen-

gage the pawl and metal clips.

CAUTION:

Remove pawl and metal clips slowly so that they are not

damaged.

6. Remove instrument lower cover RH.

1. Put front seat assembly RH to rearmost position.

2. Remove fixing clip (A).

3. Pull the instrument lower cover RH crosswise, and disen-

gage the pawl and metal clips.

CAUTION:

Remove pawl and metal clips slowly so that they are not

damaged.

7. Remove center console assembly.

1. Remove center console fixing screws (A).

2. Remove seat heated switch harness clip (with seat heated switch).

3. Lift up center console assembly back side.

CAUTION:

Be careful not for damaging parts in surrounding area.

8. Release front pillar portion of front body side welt LH. Refer to

INT-21, "BODY SIDE WELT : Removal and

Installation"

9. Remove front pillar garnish LH. Refer to

INT-18, "FRONT PILLAR GARNISH : Removal and Installation"

10. Remove instrument side finisher LH.

1. Insert remover tool (A) between instrument side finisher LH

and instrument panel assembly to disengage the pawls as

shown in the figure.

2. Pull back instrument side finisher LH.

CAUTION:

Apply protective tape (B) on the part to protect it from dam-

age.

11. Remove instrument lower panel LH.

: Pawl

: Metal clip

JMJIA4551ZZ

: Pawl

: Metal clip

JMJIA4552ZZ

JMJIA4553ZZ

: Pawl

JMJIA4554ZZ

Revision: November 2015

2016 JUKE

INSTRUMENT PANEL ASSEMBLY

IP-17

< REMOVAL AND INSTALLATION >

1. Remove hood opener and fuel lid opener lever. Refer to

DLK-155, "HOOD LOCK CONTROL CABLE

: Removal and Installation"

(with Intelligent Key System).

2. Remove fixing screw (A).

3. Pull back instrument lower panel LH, and then disengage

the pawls and metal clips.

4. Disconnect harness connectors and aspirator duct.

12. Remove driver air bag module. Refer to

SR-12, "Removal and Installation"

13. Remove steering wheel. Refer to

ST-9, "Removal and Installation"

14. Remove steering column covers.

without paddle shifter

1. Place the tilt to the lowest level.

2. Remove steering lock escutcheon (1). (without Intelligent

Key)

3. Remove fixing screws (A).

4. Pull up steering column upper cover (2), and then disen-

gage steering column upper cover fixing pawls.

5. Remove steering column upper cover.

6. Pull down the steering column lower cover (3), and then

remove steering column lower cover.

NOTE:

Disengage the pawls, and then remove steering lock escutch-

eon (4). (with Intelligent Key)

with paddle shifter

1. Place the tilt to the lowest level.

2. Remove fixing screws (A).

3. Pull up steering column upper cover (1), and then disen-

gage steering column upper cover fixing pawls.

4. Remove steering column upper cover.

5. Disengage fixing pawls, and then remove steering column

LH cover (2).

6. Disengage fixing pawls, and then remove steering column

RH cover (3).

7. Remove fixing screws (B).

8. Pull down the steering column lower cover (4), and then

remove steering column lower cover.

: Pawl

: Metal clip

JMJIA4556ZZ

: Pawl

JMJIB0706ZZ

: Pawl

JMJIB0702ZZ

Revision: November 2015

2016 JUKE

IP-18

< REMOVAL AND INSTALLATION >

INSTRUMENT PANEL ASSEMBLY

15. Remove spiral cable. Refer to

SR-15, "Removal and Installation"

16. Remove combination switch. Refer to

BCS-95, "Removal and Installation"

(with Intelligent Key System).

17. Remove cluster lid A.

1. Cover steering shaft with a shop cloth (A) to prevent dam-

age.

2. Pull back cluster lid A while holding the lower side and dis-

engage the metal clips underside.

3. Hold both upper sides of cluster lid A and pull it out towards

vehicle rear, and disengage pawl and metal clips topside.

4. Disconnect push-button ignition switch harness connector

and NATS antenna amp.harness connector. (with Intelligent

Key)

CAUTION:

Remove metal clips slowly so that they are not damaged.

18. Remove combination meter. Refer to

MWI-64, "Removal and Installation"

19. Remove multi display unit (with auto A/C) or A/C finisher (with manual A/C).

Multi display unit (with auto A/C)

1. Apply protective tape (B) on instrument panel assembly (2) to protect it from damage.

: Pawl

: Metal clip

JMJIA4557ZZ

Multi display unit (with auto A/C)

Instrument panel assembly
(with auto A/C models)

Intake door lever knob

A/C finisher (with manual A/C)

Instrument panel assembly
(with manual A/C models)

: Pawl

: Metal clip

JMJIA4558ZZ

Revision: November 2015

2016 JUKE

INSTRUMENT PANEL ASSEMBLY

IP-19

< REMOVAL AND INSTALLATION >

2. Insert a remover tool (A) into the cutouts at the bottom of

multi display unit (1), then pull straight back to disengage

the pawls and metals clips.

3. Pull back multi display unit, and then disconnect harness connector.

A/C finisher (with manual A/C)

1. Apply a protective tape (B) on instrument panel assembly (5) to protect it from damage.

2. Hold intake door lever knob (1) from upper side and lower

side, tilt it to the right and the left, and then disengage it

from intake door lever (2). Pull up intake door lever knob

and remove it from intake door lever.

3. Insert a remover tool (A) into the cutouts at the bottom of multi display unit (4), then pull straight back

to disengage pawls and metal clips.

4. Pull back A/C finisher.

20. Remove A/C control fixing screws (with Manual A/C). Refer to

HAC-151, "Removal and Installation"

: Pawl

: Metal clip

JMJIA6909ZZ

JMJIA6910ZZ

Revision: November 2015

2016 JUKE

IP-20

< REMOVAL AND INSTALLATION >

INSTRUMENT PANEL ASSEMBLY

21. Remove cluster lid C.

1. Remove fixing screws (A).

2. Pull back cluster lid C, and disengage the pawls and metal

clips.

3. Disconnect harness connector.

22. Remove audio unit or NAVI C/U.

• Audio unit: Refer to

AV-50, "Removal and Installation"

• NAVI C/U: Refer to

AV-182, "Removal and Installation"

23. Disconnect hazard switch harness connector.
24. Remove cluster tray.

1. Insert a remover tool (A) between cluster tray and instru-

ment panel assembly, and then pull downward and disen-

gage metal clips.

2. Pull back cluster tray.

3. Disconnect harness connectors.

CAUTION:

Apply protective tape (B) on the part to protect it from dam-

age.

25. Release front pillar portion of front body side welt RH. Refer to

INT-21, "BODY SIDE WELT : Removal and

Installation"

26. Remove front pillar garnish RH. Refer to

INT-18, "FRONT PILLAR GARNISH : Removal and Installation"

27. Remove instrument side finisher RH.

1. Insert remover tool (A) between instrument side finisher RH

and instrument panel assembly to disengage the pawls as

shown in the figure.

2. Pull back instrument side finisher RH.

CAUTION:

Apply protective tape (B) on the part to protect it from dam-

age.

28. Remove glove box lid.

1. Open glove box lid.

2. Pull glove box lid (1) toward vehicle rear, and then disen-

gage the joint from instrument panel assembly (2).

: Pawl

: Metal clip

JMJIA4559ZZ

: Metal clip

JMJIA4560ZZ

: Pawl

JMJIA4561ZZ

JMJIA4563ZZ

Revision: November 2015

2016 JUKE

INSTRUMENT PANEL ASSEMBLY

IP-21

< REMOVAL AND INSTALLATION >

3. Disengage the pawl, and then remove damper pin on right

side.

CAUTION:

Never excessively pull string of glove box damper.

29. Remove glove box assembly.

1. Remove fixing screws (A).

2. Pull back the glove box cover assembly while holding the lower side and disengage the pawls.

3. Disconnect glove box lamp harness connector.

30. Remove passenger air bag module. Refer to

SR-18, "Removal and Installation"

31. Remove switch panel.

1. Insert remover tool (A) between switch panel and instru-

ment panel assembly to disengage the pawls as shown in

the figure.

2. Pull up switch panel, and then disconnect harness connec-

tors.

CAUTION:

Apply protective tape (B) on the part to protect it from dam-

age.

32. Remove instrument panel assembly.

: Pawl

JMJIA4564ZZ

: Pawl

JMJIA4565ZZ

: Pawl

JMJIA4566ZZ

Revision: November 2015

2016 JUKE

Content .. 454 455 456 457 ..