Content .. 450 451 452 453 ..

Nissan Juke (2016 year). Service Repair Manual - part 452

INT-22

< REMOVAL AND INSTALLATION >

BODY SIDE TRIM

1. Remove front kicking plate inner. Refer to

INT-19, "KICKING PLATE INNER : Removal and Installation"

2. Remove front body side welt.

REAR BODY SIDE WELT

1. Remove rear kicking plate inner. Refer to

INT-19, "KICKING PLATE INNER : Removal and Installation"

2. Remove rear body side welt.

INSTALLATION

Install in the reverse order of removal.

CENTER PILLAR LOWER GARNISH
CENTER PILLAR LOWER GARNISH : Removal and Installation

INFOID:0000000012199177

REMOVAL

CAUTION:

• When removing, always use a remover tool that is made of plastic.

• Never damage the body.

1. Fully open front door and rear door.
2. Slide front seat to the fully forward position. Tilt seatback forward.
3. Remove Front body side welt and rear body side welt. Refer to

INT-21, "BODY SIDE WELT : Removal

and Installation"

4. Disengage center pillar lower garnish fixing clips and pawls with

a remover tool (A), and then remove center pillar lower garnish.

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:

When installing center pillar lower garnish, check that clips are securely in body panel holes, and

press them in.

CENTER PILLAR UPPER GARNISH
CENTER PILLAR UPPER GARNISH : Removal and Installation

INFOID:0000000012199178

REMOVAL

CAUTION:

• When removing, always use a remover tool that is made of plastic.

• Never damage the body.

1. Remove center pillar lower garnish. Refer to

INT-22, "CENTER PILLAR LOWER GARNISH : Removal

and Installation"

2. Remove front seat belt shoulder anchor. Refer to

SB-6, "SEAT BELT RETRACTOR : Removal and Instal-

lation"

: Clip

: Pawl

JMJIA4390ZZ

Revision: November 2015

2016 JUKE

BODY SIDE TRIM

INT-23

< REMOVAL AND INSTALLATION >

INT

3. Disengage center pillar upper garnish lower side fixing pawl

using a remover tool.

4. Disengage center pillar upper garnish upper side fixing clip using a remover tool (A).

NOTE:

Removal operation can be performed easily when pressing pawl by inserting a removal tool from direction

(A) as shown in the figure.

CAUTION:

Be careful not to apply excessive force when removing center pillar upper garnish. Otherwise,

pawl may be damaged and fragments may drop in panel holes on body.

INATALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:

• Replace center pillar upper garnish with a new part after removal. Never reuse center pillar upper

garnish.

• When installing center pillar upper garnish, check that pawls are securely in body panel holes, and

press them in.

: Pawl

JMJIA4391ZZ

PIIB7674J

Revision: November 2015

2016 JUKE

INT-24

< REMOVAL AND INSTALLATION >

FLOOR TRIM

FLOOR TRIM

Exploded View

INFOID:0000000012199179

Removal and Installation

INFOID:0000000012199180

REMOVAL

CAUTION:

• When removing, always use a remover tool that is made of plastic.

• Never damage the body.

1. Remove front seat assembly (LH and RH). Refer to

SE-21, "Removal and Installation"

2. Remove rear seat cushion. Refer to

SE-32, "SEAT CUSHION : Removal and Installation"

3. Remove center console assembly. Refer to

IP-24, "Removal and Installation"

4. Remove instrument stay.

Floor carpet

Carpet hook

Trim clip

Column hole cover

Harness clip

Front floor spacer RH

Front floor spacer LH

Rear floor spacer LH

Rear floor spacer RH

: Clip

: Pawl

JMJIA4530ZZ

Revision: November 2015

2016 JUKE

FLOOR TRIM

INT-25

< REMOVAL AND INSTALLATION >

INT

Remove instrument stay mounting nuts (A), and then remove

instrument stay.

5. Disconnect drain hose. Refer to

HA-43, "A/C UNIT ASSEMBLY : Removal and Installation"

6. Remove foot ducts (LH and RH). Refer to

VTL-13, "FOOT DUCT : Removal and Installation"

(Models with

foot ducts).

7. Remove shift selector assembly

• 6MT models: Refer to

TM-25, "Removal and Installation"

• CVT models: Refer to

TM-316, "Removal and Installation"

8. Remove diagnosis sensor unit. Refer to

SR-29, "Removal and Installation"

9. Remove parking brake lever. Refer to

PB-7, "Removal and Installation"

10. Remove center pillar lower garnish (LH and RH). Refer to

INT-22, "CENTER PILLAR LOWER GARNISH :

Removal and Installation"

11. Remove column hole cover.

Disengage trim clip (A), and then remove column hole cover.

12. Remove dash side finisher (LH and RH). Refer to

INT-21, "DASH SIDE FINISHER : Removal and Installa-

tion"

13. Disengage pawl using a remover tool (A) and open the harness

clip.

14. Remove floor carpet.

NOTE:

: Vehicle front

JMJIA4531ZZ

JMJIA4532ZZ

: Pawl

JMJIA4396ZZ

Revision: November 2015

2016 JUKE

INT-26

< REMOVAL AND INSTALLATION >

FLOOR TRIM

Disengage pawls using a remover tool and remove carpet hook.

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:

Replace diagnosis sensor unit fixing bolts with a new part after removal. Never reuse diagnosis sen-

sor unit fixing bolts.

: Pawl

JMJIA3620ZZ

Revision: November 2015

2016 JUKE

HEADLINING

INT-27

< REMOVAL AND INSTALLATION >

INT

HEADLINING

NORMAL ROOF
NORMAL ROOF : Exploded View

INFOID:0000000012199181

NORMAL ROOF

NORMAL ROOF : Removal and Installation

INFOID:0000000012199182

REMOVAL

JMJIA4533ZZ

Headlining assembly

Assist grip clip

Rear assist grip RH

Front assist grip RH

Sun visor assembly RH

Sun visor cover RH

Sun visor cover LH

Sun visor assembly LH

Rear assist grip LH

10. Headlining clip

11. Sun visor holder RH

12. Map lamp

13. Sun visor holder LH

14. Metal clip

: Clip

: Pawl

Revision: November 2015

2016 JUKE

INT-28

< REMOVAL AND INSTALLATION >

HEADLINING

CAUTION:

• When removing, always use a remover tool that is made of plastic.

• Never damage the body.

1. Remove front pillar garnish (LH and RH). Refer to

INT-18, "FRONT PILLAR GARNISH : Removal and

Installation"

2. Disconnect harness connector (A) from headlining and harness

clips

3. Remove center pillar upper garnish (LH and RH). Refer to

INT-22, "CENTER PILLAR UPPER GARNISH :

Removal and Installation"

4. Remove back door weather-strip. Refer to

DLK-152, "BACK DOOR WEATHER-STRIP : Removal and

Installation"

(with Intelligent Key System).

5. Remove luggage side upper finisher (LH and RH). Refer to

INT-36, "LUGGAGE SIDE UPPER FINISHER

: Removal and Installation"

6. Remove all assist grips.

1. Disengage pawl of assist grip clip (1) using a remover tool

(A). Slide assist grip clip forward and remove it.

2. Slide assist grip (2) forward and remove it.

3. Remove metal clips.

7. Remove sun visor assembly (LH and RH).

1. Disengage sun visor cover fixing pawls with a remover tool

(A), and then remove sun visor cover.

2. Remove sun visor assembly fixing screws, and then slide toward vehicle rear to remove sun visor

assembly.

8. Remove map lamp assembly. Refer to

INL-46, "Removal and Installation"

9. Remove front seat assembly (passenger). Refer to

SE-21, "Removal and Installation"

10. Remove sun visor holder (LH and RH).

: Clip

JMJIA4534ZZ

: Pawl

JMJIA4398ZZ

: Pawl

JMJIA4399ZZ

Revision: November 2015

2016 JUKE

HEADLINING

INT-29

< REMOVAL AND INSTALLATION >

INT

Rotate 90

. Remove toward vehicle lower.

11. Remove headlining clips.
12. Remove headlining assembly through the back door.

CAUTION:

• Two workers are required for removal in order to prevent

damage.

• Apply protective tape to the portion where contact may

occur during work.

• Never bend headlining when removing.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:

• When installing headlining, start by installing both sun visor holders and headlining clips in order to

keep the headlining in position.

• Never bend headlining when installing.

• Be careful that the surface is not wrinkled when installing.

SUNROOF

JMJIA4401ZZ

JMJIA4402ZZ

Revision: November 2015

2016 JUKE

Content .. 450 451 452 453 ..