Nissan Juke (2016 year). Service Repair Manual - part 439

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     437      438      439      440     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 439

 

 

COMPRESSOR DOES NOT OPERATE

HAC-149

< SYMPTOM DIAGNOSIS >

[MANUAL AIR CONDITIONING]

C

D

E

F

G

H

J

K

L

M

A

B

HAC

N

O

P

COMPRESSOR DOES NOT OPERATE

Description

INFOID:0000000012200142

SYMPTOM

Compressor does not operate. 

Diagnosis Procedure

INFOID:0000000012200143

NOTE:

• Perform self-diagnosis with CONSULT before performing symptom diagnosis. If any malfunction result or

DTC is detected, perform the corresponding diagnosis.

• Check that refrigerant is enclosed in cooler cycle normally. If the refrigerant amount is shortage from proper

amount, perform the inspection of refrigerant leakage

1.

CHECK A/C INDICATOR

1. Turn ignition switch ON.

2. Operate blower motor.

3. Check that A/C indicator is turned ON/OFF when operating A/C switch.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 5.

2.

CHECK MAGNET CLUTCH OPERATION

Check magnet clutch. Refer to 

HAC-144, "Component Function Check"

. 

Does it operate normally?

YES

>> GO TO 3.

NO

>> Repair or replace malfunctioning parts.

3.

CHECK REFRIGERANT PRESSURE SENSOR

Check refrigerant pressure sensor. Refer to 

EC-568, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace malfunctioning parts.

4.

CHECK BCM OUTPUT SIGNAL

With CONSULT

1. Select “DATA MONITOR” mode of “ECM” using CONSULT.

2. Select “AIR COND SIG” and “HEATER FAN SW”, and check status under the following conditions.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

NO

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

5.

CHECK A/C SWITCH

Check A/C switch. Refer to 

HAC-130, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts. 

6.

CHECK BLOWER FAN ON SIGNAL

Monitor item

Condition

Status

AIR COND SIG

A/C switch

OFF (A/C indicator: OFF)

Off

ON (A/C indicator: ON)

On

HEATER FAN SW

Blower motor

OFF

Off

ON

On

Revision: November 2015

2016 JUKE

HAC-150

< SYMPTOM DIAGNOSIS >

[MANUAL AIR CONDITIONING]

COMPRESSOR DOES NOT OPERATE

Check blower fan ON signal. Refer to 

HAC-132, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace the malfunctioning parts

7.

CHECK THERMO CONTROL AMP.

Check thermo control amp. Refer to 

HAC-134, "Component Function Check"

.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> Repair or replace the malfunctioning parts

Revision: November 2015

2016 JUKE

A/C CONTROL

HAC-151

< REMOVAL AND INSTALLATION >

[MANUAL AIR CONDITIONING]

C

D

E

F

G

H

J

K

L

M

A

B

HAC

N

O

P

REMOVAL AND INSTALLATION

A/C CONTROL

Exploded View

INFOID:0000000012200144

Removal and Installation

INFOID:0000000012200145

REMOVAL

1. Remove A/C finisher. Refer to 

IP-13, "Removal and Installation"

.

2. Remove fixing screws (A) and fixing pawls, and then remove A/

C control.

3. Disconnect door cable and harness connector from A/C control.

INSTALLATION

Install in the reverse order of removal.

1.

Air mix door cable

2.

Intake door cable

3.

A/C control

4.

Mode door cable

5.

Intake door lever knob

A.

To air mix door link

B.

To intake door link

C.

To mode door link

JMIIA0899ZZ

: Pawl

JMIIA0900ZZ

Revision: November 2015

2016 JUKE

HAC-152

< REMOVAL AND INSTALLATION >

[MANUAL AIR CONDITIONING]

THERMO CONTROL AMPLIFIER

THERMO CONTROL AMPLIFIER

Removal and Installation

INFOID:0000000012200146

REMOVAL

1. Remove evaporator. Refer to 

HA-46, "EVAPORATOR : Removal and Installation"

.

2. Disconnect thermo control amp. from evaporator.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

• Replace O-ring with new one. Then apply compressor oil to them when installing.

• When install the thermo control amp., set the same position before replacement.

• When remove the thermo control amp., never turn the bracket which is equipped the top of the

thermo control amp. 

• Check for the leakages when recharging refrigerant. Refer to 

HA-17, "Leak Test"

.

Revision: November 2015

2016 JUKE

REFRIGERANT PRESSURE SENSOR

HAC-153

< REMOVAL AND INSTALLATION >

[MANUAL AIR CONDITIONING]

C

D

E

F

G

H

J

K

L

M

A

B

HAC

N

O

P

REFRIGERANT PRESSURE SENSOR

Exploded View

INFOID:0000000012200147

Refer to 

HA-36, "Exploded View"

.

Removal and Installation

INFOID:0000000012200148

REMOVAL

Refer to 

HA-38, "REFRIGERANT PRESSURE SENSOR : Removal and Installation"

.

INSTALLATION

Install in the reverse order of removal.

Revision: November 2015

2016 JUKE

HAC-154

< REMOVAL AND INSTALLATION >

[MANUAL AIR CONDITIONING]

BLOWER FAN RESISTOR

BLOWER FAN RESISTOR

Exploded View

INFOID:0000000012200149

• *1: Manual air conditioning
• *2: Automatic air conditioning

Removal and Installation

INFOID:0000000012200150

REMOVAL

1. Remove instrument panel assembly. Refer to 

IP-13, "Removal and Installation"

.

2. Disconnect blower fan resistor harness connector.
3. Remove fixing screws, and then remove blower fan resistor from A/C unit assembly.

INSTALLATION

Install in the reverse order of removal.

1.

A/C unit assembly

2.

Blower fan resistor*

1

3.

Sub harness*

1

4.

Power transistor*

2

5.

Sub harness*

2

6.

Blower motor

JPIIA1549ZZ

Revision: November 2015

2016 JUKE

DOOR CABLE

HAC-155

< REMOVAL AND INSTALLATION >

[MANUAL AIR CONDITIONING]

C

D

E

F

G

H

J

K

L

M

A

B

HAC

N

O

P

DOOR CABLE

Exploded View

INFOID:0000000012200151

LEFT SIDE

RIGHT SIDE

1.

A/C unit assembly

2.

Intake door lever

3.

Intake door link

4.

Intake door cable

5.

Air mix door cable

6.

Upper air mix door rod

7.

Upper air mix door lever

8.

Lower air mix door lever

9.

Lower air mix door rod

10. Air mix door link
A.

To A/C control

JPIIA1559ZZ

Revision: November 2015

2016 JUKE

HAC-156

< REMOVAL AND INSTALLATION >

[MANUAL AIR CONDITIONING]

DOOR CABLE

INTAKE DOOR CABLE
INTAKE DOOR CABLE : Removal and Installation

INFOID:0000000012200152

REMOVAL

1. Disconnect intake door cable from A/C control. Refer to 

HAC-151, "Exploded View"

.

2. Remove instrument lower panel LH. Refer to 

IP-13, "Removal and Installation"

.

3. Disconnect intake door cable from A/C unit assembly as shown

by the arrow in the figure, and then remove intake door cable.

INSTALLATION

Install in the reverse order of removal.

MODE DOOR CABLE

1.

A/C unit assembly

2.

Main link

3.

Sub defroster door link

4.

Sub defroster door rod

5.

Mode door cable

6.

Plate

7.

Mode link

8.

Sub defroster door lever

9.

Center ventilator and defroster door link

10. Plate

11. Center ventilator and defroster door rod

12. Center ventilator and defroster door lever

A.

To A/C control

JPIIA1560ZZ

JMIIA0901ZZ

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     437      438      439      440     ..