Content .. 402 403 404 405 ..

Nissan Juke (2016 year). Service Repair Manual - part 404

HOW TO USE THIS MANUAL

GI-3

< HOW TO USE THIS MANUAL >

HOW TO USE THIS MANUAL

Description

INFOID:0000000012196761

This volume explains “Removal, Disassembly, Installation, Inspection and Adjustment” and “Trouble Diag-

noses”.

Terms

INFOID:0000000012196762

• The captions

WARNING

and

CAUTION

warn you of steps that must be followed to prevent personal injury

and/or damage to some part of the vehicle.

WARNING

indicates the possibility of personal injury if instructions are not followed.

CAUTION

indicates the possibility of component damage if instructions are not followed.

BOLD TYPED STATEMENTS

except

WARNING

and

CAUTION

give you helpful information.

Standard value: Tolerance at inspection and adjustment.

Limit value: The maximum or minimum limit value that should not be exceeded at inspection and adjust-

ment.

Units

INFOID:0000000012196763

• The

UNITS

given in this manual are primarily expressed as the SI UNIT (International System of Unit), and

alternatively expressed in the metric system and in the yard/pound system.

Also with regard to tightening torque of bolts and nuts, there are descriptions both about range and about the

standard tightening torque.

“Example”

Range

Standard

Contents

INFOID:0000000012196764

•

A QUICK REFERENCE INDEX

, a black tab (e.g.

) is provided on the first page. You can quickly find the

first page of each section by matching it to the section's black tab.

•

THE CONTENTS

are listed on the first page of each section.

•

THE TITLE

is indicated on the upper portion of each page and shows the part or system.

•

THE PAGE NUMBER

of each section consists of two or three letters which designate the particular section

and a number (e.g. “BR-5”).

•

THE SMALL ILLUSTRATIONS

show the important steps such as inspection, use of special tools, knacks of

work and hidden or tricky steps which are not shown in the previous large illustrations.

Assembly, inspection and adjustment procedures for the complicated units such as the automatic transaxle

or transmission, etc. are presented in a step-by-step format where necessary.

Outer Socket Lock Nut

: 59 - 78 N·m (6.0 - 8.0 kg-m, 43 - 58 ft-lb)

Drive Shaft Installation Bolt : 44.3 N·m (4.5 kg-m, 33 ft-lb)

Revision: November 2015

2016 JUKE

GI-4

< HOW TO USE THIS MANUAL >

HOW TO USE THIS MANUAL

Relation between Illustrations and Descriptions

INFOID:0000000012196765

The following sample explains the relationship between the part description in an illustration, the part name in

the text and the service procedures.

Components

INFOID:0000000012196766

•

THE LARGE ILLUSTRATIONS

are exploded views (see the following) and contain tightening torques, lubri-

cation points, section number of the

PARTS CATALOG

(e.g. SEC. 440) and other information necessary to

perform repairs.

The illustrations should be used in reference to service matters only. When ordering parts, refer to the appro-

priate

PARTS CATALOG

Components shown in an illustration may be identified by a circled number. When this style of illustration is

used, the text description of the components will follow the illustration.

SAIA0519E

Revision: November 2015

2016 JUKE

HOW TO USE THIS MANUAL

GI-5

< HOW TO USE THIS MANUAL >

SYMBOLS

Cap

Bleeder valve

Cylinder body

Piston seal

Piston

Piston boot

Sliding pin

Sliding pin boot

Bushing

10. Torque member

: Apply rubber grease.

: Apply brake fluid.

: N·m (kg-m, in-lb)

:Always replace after every disassembly.

JPFIA0511GB

SAIA0749E

Revision: November 2015

2016 JUKE

GI-6

< HOW TO USE THIS MANUAL >

HOW TO FOLLOW TROUBLE DIAGNOSES

HOW TO FOLLOW TROUBLE DIAGNOSES

Description

INFOID:0000000012196767

NOTICE:

Trouble diagnoses indicate work procedures required to diagnose problems effectively. Observe the following

instructions before diagnosing.

• Before performing trouble diagnoses, read the “Work Flow” in each section.

• After repairs, re-check that the problem has been completely eliminated.

• Refer to Component Parts and Harness Connector Location for the Systems described in each section for

identification/location of components and harness connectors.

• When checking circuit continuity, ignition switch should be OFF.

• Refer to the Circuit Diagram for quick pinpoint check.

If you need to check circuit continuity between harness connectors in more detail, such as when a sub-har-

ness is used, refer to Wiring Diagram in each individual section and Harness Layout in PG section for identi-

fication of harness connectors.

• Before checking voltage at connectors, check battery voltage.

• After accomplishing the Diagnosis Procedures and Electrical Components Inspection, check that all harness

connectors are reconnected as they were.

How to Follow Test Groups in Trouble Diagnosis

INFOID:0000000012196768

1. Test group number and test group title

• Test group number and test group title are shown in the upper portion of each test group.

2. Work and diagnosis procedure

• Start to diagnose a problem using procedures indicated in enclosed test groups.

3. Questions and results

• Questions and required results are indicated in test group.

4. Action

• Next action for each test group is indicated based on result of each question.

JPAIA0021GB

Revision: November 2015

2016 JUKE

HOW TO FOLLOW TROUBLE DIAGNOSES

GI-7

< HOW TO USE THIS MANUAL >

Key to Symbols Signifying Measurements or Procedures

INFOID:0000000012196769

JPAIA0982GB

Revision: November 2015

2016 JUKE

GI-8

< HOW TO USE THIS MANUAL >

HOW TO FOLLOW TROUBLE DIAGNOSES

JSAIA1461GB

Revision: November 2015

2016 JUKE

HOW TO READ WIRING DIAGRAMS

GI-9

< HOW TO USE THIS MANUAL >

HOW TO READ WIRING DIAGRAMS

Connector Symbols

INFOID:0000000012196770

Most of connector symbols in wiring diagrams are shown from the terminal side.

• Connector symbols shown from the terminal side are enclosed by

a single line and followed by the direction mark.

• Connector symbols shown from the harness side are enclosed by

a double line and followed by the direction mark.

• Certain systems and components, especially those related to

OBD, may use a new style slide-locking type harness connector.

For description and how to disconnect, refer to PG section,

“Description”, “HARNESS CONNECTOR”.

• Male and female terminals

Connector guides for male terminals are shown in black and

female terminals in white in wiring diagrams.

SAIA0257E

SGI363

Revision: November 2015

2016 JUKE

GI-10

< HOW TO USE THIS MANUAL >

HOW TO READ WIRING DIAGRAMS

Sample/Wiring Diagram -Example-

INFOID:0000000012196771

Each section includes wiring diagrams.

Description

JCAWA0150GB

Number

Item

Description

Power supply

• This means the power supply of fusible link or fuse.

Fuse

• “/” means the fuse.

Current rating of fusible
link/fuse

• This means the current rating of the fusible link or fuse.

Number of fusible link/
fuse

• This means the number of fusible link or fuse location.

Fusible link

• “X” means the fusible link.

Connector number

• Alphabetic characters show to which harness the connector is placed.
• Numeric characters show the identification number of connectors.

Switch

• This shows that continuity exists between terminals 1 and 2 when the switch is in the A posi-

tion. Continuity exists between terminals 1 and 3 when the switch is in the B position.

Circuit (Wiring)

• This means the wiring.

Revision: November 2015

2016 JUKE

Content .. 402 403 404 405 ..