Nissan Juke (2016 year). Service Repair Manual - part 372

EXL-198

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON

BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON

Description

INFOID:0000000012201769

Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.

Diagnosis Procedure

INFOID:0000000012201770

1.

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to 

BCS-92, "Symptom Table"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK HIGH BEAM REQUEST SIGNAL

With CONSULT

1. Turn ignition switch ON.

2. Select “HL HI REQ” in “Data Monitor” mode of “IPDM E/R” using CONSULT.

3. With operating the lighting switch, check the monitor status.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

NO

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

Monitor item

Condition

Monitor status

HL HI REQ

Lighting switch
(2ND)

HI or PASS

On

LO

Off

Revision: November 2015

2016 JUKE

BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON

EXL-199

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON

Description

INFOID:0000000012201771

Both side headlamps (LO) are not turned ON in any condition.

Diagnosis Procedure

INFOID:0000000012201772

1.

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to 

BCS-92, "Symptom Table"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK LOW BEAM REQUEST SIGNAL

With CONSULT

1. Turn ignition switch ON.

2. Select “HL LO REQ” in “Data Monitor” mode of “IPDM E/R” using CONSULT.

3. With operating the lighting switch, check the monitor status.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

NO

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

Monitor item

Condition

Monitor status

HL LO REQ

Lighting switch

2ND

On

OFF

Off

Revision: November 2015

2016 JUKE

EXL-200

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT 

TURNED ON

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT
TURNED ON

Description

INFOID:0000000012201773

The parking, license plate, side marker and tail lamps are not turned ON in any condition.

Diagnosis Procedure

INFOID:0000000012201774

1.

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to 

BCS-92, "Symptom Table"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK POSITION LIGHT REQUEST SIGNAL

With CONSULT

1. Turn ignition switch ON.

2. Select “TAIL & CLR REQ” in “Data Monitor” mode of “IPDM E/R” using CONSULT.

3. With operating the lighting switch, check the monitor status.

Is the inspection result normal?

YES

>> Perform the tail lamp diagnosis. Refer to 

EXL-171, "Component Function Check"

.

NO

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

Monitor item

Condition

Monitor status

TAIL & CLR REQ Lighting switch

1ST

On

OFF

Off

Revision: November 2015

2016 JUKE

BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON

EXL-201

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON

Description

INFOID:0000000012201775

Both side front fog lamps are not turned ON in any condition.

Diagnosis Procedure

INFOID:0000000012201776

1.

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to 

BCS-92, "Symptom Table"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK FRONT FOG LIGHT REQUEST SIGNAL

With CONSULT

1. Turn ignition switch ON.

2. Select “FR FOG REQ” in “Data Monitor” mode of “IPDM E/R” using CONSULT.

3. With operating the front fog lamp switch, check the monitor status.

Is the inspection result normal?

YES

>> Perform the front fog lamp diagnosis. Refer to 

EXL-180, "Component Function Check"

.

NO

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

Monitor item

Condition

Monitor status

FR FOG REQ

Front fog lamp switch
(With lighting switch 1ST)

ON

On

OFF

Off

Revision: November 2015

2016 JUKE

EXL-202

< PERIODIC MAINTENANCE >

[HALOGEN TYPE]

HEADLAMP AIMING ADJUSTMENT

PERIODIC MAINTENANCE

HEADLAMP AIMING ADJUSTMENT

Description

INFOID:0000000012201777

PREPARATION BEFORE ADJUSTING

NOTE:

• For details, refer to the regulations in your own country.

• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been

replaced.

Before performing aiming adjustment, check the following. 

• Adjust the tire pressure to the specification.

• Fill with fuel, engine coolant and each oil.

• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the trunk

room.)

NOTE:

Do not remove the temporary tire, jack and on-vehicle tool. 

• Wipe out dirt on the headlamp.

CAUTION:

Never use organic solvent (thinner, gasoline etc.).

• Ride alone on the driver seat.

AIMING ADJUSTMENT SCREW

Aiming Adjustment Procedure

INFOID:0000000012201778

1. Place the screen.

NOTE:

• Stop the vehicle facing the wall.

• Place the board on a plain road vertically.

JMLIA6147ZZ

A. Headlamp RH (UP/DOWN) adjustment screw B.

Headlamp LH (UP/DOWN) adjustment screw

: Vehicle front

Adjustment screw

Screw driver rotation

Facing direction

A

Headlamp LH (UP/DOWN)

Clockwise

DOWN

Counterclockwise

UP

B

Headlamp RH (UP/DOWN)

Clockwise

DOWN

Counterclockwise

UP

Revision: November 2015

2016 JUKE

HEADLAMP AIMING ADJUSTMENT

EXL-203

< PERIODIC MAINTENANCE >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

2. Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the headlamp center and the screen.
3. Start the engine. Turn the headlamp (LO) ON.

CAUTION:

Never cover the lens surface with a tape etc. The lens is made of resin.

NOTE:

Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.

4. Measure the distance (X) between the horizontal center line of headlamp (H) and the cutoff line (A) within

the light axis measurement range (R) from the vertical center line ahead of headlamp (V).

Low beam distribution on the screen 

5. Adjust the cutoff line height (X) with the aiming adjustment screw so as to enter in the adjustment range

(M–N) according to the horizontal center line of headlamp (H).

unit: mm (in)

Side view

Light axis measurement range (R)

: 350 

±

 175 mm (13.78 

±

 6.89 in)

JSLIA0005ZZ

Horizontal center line of headlamp (H)

Highest cutoff line height (M)

Lowest cutoff line height (N)

700 (27.56) or less

4 (0.16)

30 (1.18)

701(27.60) – 800 (31.50)

4 (0.16)

30 (1.18)

801 (31.54) or more

17 (0.67)

44 (1.73)

JSLIA0006ZZ

Distance between the headlamp center and the screen (L)

: 10 m (32.8 ft)

Revision: November 2015

2016 JUKE

EXL-204

< PERIODIC MAINTENANCE >

[HALOGEN TYPE]

FRONT FOG LAMP AIMING ADJUSTMENT

FRONT FOG LAMP AIMING ADJUSTMENT

Description

INFOID:0000000012201779

PREPARATION BEFORE ADJUSTING

NOTE:

• For details, refer to the regulations in your own country.

• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been

replaced.

Before performing aiming adjustment, check the following. 

• Adjust the tire pressure to the specification.

• Fill with fuel, engine coolant and each oil.

• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the trunk

room.)

NOTE:

Do not remove the temporary tire, jack and on-vehicle tool. 

• Wipe out dirt on the headlamp.

CAUTION:

Never use organic solvent (thinner, gasoline etc.).

• Ride alone on the driver seat.

AIMING ADJUSTMENT SCREW

• Turn the aiming adjusting screw for adjustment.

• For the position and direction of the adjusting screw, refer to the

figure.

NOTE:

A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used

for adjustment.

Aiming Adjustment Procedure

INFOID:0000000012201780

1. Place the screen.

NOTE:

• Stop the vehicle facing the wall.

• Place the board on a plain road vertically.

2. Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the

screen.

3. Start the engine. Turn the front fog lamp ON.

CAUTION:

Never cover the lens surface with a tape etc. The lens is made of resin.

NOTE:

Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.

4. Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-

izontal center line of front fog lamp (H) and (A) becomes 150 mm (5.91 in).

A: UP
B: DOWN

JMLIA1249ZZ

Revision: November 2015

2016 JUKE

FRONT FOG LAMP AIMING ADJUSTMENT

EXL-205

< PERIODIC MAINTENANCE >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Front fog lamp light distribution on the screen 

JPLIA0008ZZ

A

: Cutoff line

B

: High illuminance area

H

: Horizontal center line of front fog lamp

V

: Vertical center line of front fog lamp

X

: Cutoff line height

Revision: November 2015

2016 JUKE