Nissan Juke (2016 year). Service Repair Manual - part 371

EXL-190

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

SYMPTOM DIAGNOSIS

EXTERIOR LIGHTING SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000012201767

EXCEPT FOR NISMO MODELS

Without Daytime Running Light System

NOTE:

Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any

DTC is detected.

Symptom

Possible cause

Inspection item

Headlamp (HI) is not turned 
ON

One side

• Fuse
• Headlamp (HI) power supply/

ground circuit

• Headlamp (HI) bulb
• Headlamp assembly
- Harness
• IPDM E/R

Headlamp (HI) circuit
Refer to 

EXL-162, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis

 “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to 

EXL-198, "Diagnosis Procedure"

.

High beam indicator lamp is not turned ON
[Headlamp (HI) is turned ON]

Combination meter

• Combination meter

Data monitor “HI-BEAM IND”

• BCM (HEAD LAMP)

Active test “HEAD LAMP”

Headlamp (LO) is not 
turned ON

One side

• Fuse
• Headlamp (LO) power supply/

ground circuit

• Headlamp (LO) bulb

(Xenon bulb)

• Headlamp assembly
- HID control unit
- Xenon bulb socket
- Harness
• IPDM E/R

Headlamp (LO) circuit
Refer to 

EXL-165, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis

“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to 

EXL-199, "Diagnosis Procedure"

.

Each lamp is not turned ON/OFF with lighting switch 
AUTO

• Combination switch input/output 

signal circuit

• Combination switch
• BCM

Combination switch
Refer to 

BCS-92, "Symptom Table"

.

• Optical sensor power supply/

ground/signal circuit

• Optical sensor
• BCM

Optical sensor
Refer to 

EXL-185, "Component Func-

tion Check"

.

Parking lamp is not turned ON

• Parking lamp power supply/

ground circuit

• Front combination lamp
- LED  (Parking  lamp)
- Harness
• IPDM E/R

Parking lamp circuit
Refer to 

EXL-167, "Component Func-

tion Check"

.

Front side marker lamp is not turned ON

• Front side marker lamp power 

supply/ground circuit

• Front side marker lamp bulb
• Front side marker lamp bulb sock-

et

Front side marker lamp circuit
Refer to 

EXL-169, "Component Func-

tion Check"

.

Revision: November 2015

2016 JUKE

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-191

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Tail lamp is not turned ON

Stop lamp / Tail lamp 
(Bulb side)

• Fuse
• Tail lamp power supply/ground 

circuit

• Stop lamp / Tail lamp bulb 
• Stop lamp / Tail lamp bulb socket/

harness

• IPDM E/R

Tail lamp circuit
Refer to 

EXL-171, "Component Func-

tion Check"

.

Tail lamp (LED side)

• Fuse
• Tail lamp power supply/ground 

circuit

• Rear combination lamp internal 

circuit

- LED  (Tail  lamp)
• Tail lamp harness
• IPDM E/R

License plate lamp is not turned ON

• License plate lamp power supply/

ground circuit

• License plate lamp bulb
• License plate lamp bulb socket/

harness

License plate lamp circuit
Refer to 

EXL-173, "Component Func-

tion Check"

.

Parking lamp, license plate lamp, side marker lamp and 
tail lamp are not turned ON

Symptom diagnosis

“PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT 
TURNED ON”
Refer to 

EXL-200, "Diagnosis Procedure"

.

Position lamp indicator is not turned ON
(Parking lamp, license plate lamp, side marker lamp 
and tail lamp are turned ON)

Combination meter

• Combination meter

Data monitor “LIGHT IND”

• BCM (HEAD LAMP)

Active test “TAIL LAMP”

Front fog lamp is not turned 
ON

One side

• Front fog lamp power supply/

ground circuit

• Front fog lamp bulb
• IPDM E/R

Front fog lamp circuit
Refer to 

EXL-180, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis

“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to 

EXL-201, "Diagnosis Procedure"

.

Turn signal lamp does not 
blink

Indicator lamp is normal
(Applicable side per-
forms high flasher activa-
tion)

• Front turn signal lamp
- Front turn signal lamp power sup-

ply/ground circuit

- Front turn signal lamp bulb 
- Front turn signal lamp bulb socket
- BCM
• Side turn signal lamp
- Side turn signal lamp power sup-

ply/ground circuit

- Side turn signal lamp
- BCM
• Rear turn signal lamp
- Rear turn signal lamp power sup-

ply/ground circuit

- Rear turn signal lamp bulb 
- Rear turn signal lamp bulb socket/

harness

- BCM

Turn signal lamp circuit
Refer to 

EXL-182, "Component Func-

tion Check"

.

Indicator lamp is included

• Combination switch input/output 

signal circuit

• Combination switch
• BCM

Combination switch
Refer to 

BCS-92, "Symptom Table"

.

Symptom

Possible cause

Inspection item

Revision: November 2015

2016 JUKE

EXL-192

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

With Daytime Running Light System

NOTE:

Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any

DTC is detected.

Turn signal indicator lamp 
does not blink
(Turn signal lamp is normal)

One side

Combination meter

—

Both sides
(Always)

• Turn indicator signal
• BCM
• Combination meter

• Combination meter 

Data monitor “TURN IND”

• BCM (FLASHER)

Active test “FLASHER”

Both sides
(Only when activating 
hazard warning lamp 
with ignition switch OFF)

• Combination meter power supply/

ground circuit

• Combination meter

Combination meter
Power supply and ground circuit
Refer to 

MWI-53, "COMBINATION 

METER : Diagnosis Procedure"

.

• Hazard warning lamp does not activate

(Turn signal is normal)

• Hazard warning lamp continues activating

• Hazard switch signal/ground cir-

cuit

• Hazard switch
• BCM

Hazard switch
Refer to 

EXL-188, "Component Func-

tion Check"

.

Symptom

Possible cause

Inspection item

Symptom

Possible cause

Inspection item

Headlamp (HI) is not turned 
ON

One side

• Fuse
• Headlamp (HI) power supply/

ground circuit

• Daytime running light relay
• Headlamp (HI) bulb
• Headlamp assembly
- Harness
• IPDM E/R

Headlamp (HI) circuit
Refer to 

EXL-162, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis

 “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to 

EXL-198, "Diagnosis Procedure"

.

High beam indicator lamp is not turned ON
[Headlamp (HI) is turned ON]

Combination meter

• Combination meter

Data monitor “HI-BEAM IND”

• BCM (HEAD LAMP)

Active test “HEAD LAMP”

Headlamp (LO) is not 
turned ON

One side

• Fuse
• Headlamp (LO) power supply/

ground circuit

• Headlamp (LO) bulb

(Xenon bulb)

• Headlamp assembly
- HID control unit
- Xenon bulb socket
- Harness
• IPDM E/R

Headlamp (LO) circuit
Refer to 

EXL-165, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis

“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to 

EXL-199, "Diagnosis Procedure"

.

Parking lamp is not turned ON

• Parking lamp power supply/

ground circuit

• Front combination lamp
- LED  (Parking  lamp)
- Harness
• IPDM E/R

Parking lamp circuit
Refer to 

EXL-167, "Component Func-

tion Check"

.

Front side marker lamp is not turned ON

• Front side marker lamp power 

supply/ground circuit

• Front side marker lamp bulb
• Front side marker lamp bulb sock-

et

Front side marker lamp circuit
Refer to 

EXL-169, "Component Func-

tion Check"

.

Revision: November 2015

2016 JUKE

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-193

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Tail lamp is not turned ON

Stop lamp / Tail lamp 
(Bulb side)

• Fuse
• Tail lamp power supply/ground 

circuit

• Stop lamp / Tail lamp bulb 
• Stop lamp / Tail lamp bulb socket/

harness

• IPDM E/R

Tail lamp circuit
Refer to 

EXL-171, "Component Func-

tion Check"

.

Tail lamp (LED side)

• Fuse
• Tail lamp power supply/ground 

circuit

• Rear combination lamp internal 

circuit

- LED  (Tail  lamp)
• Tail lamp harness
• IPDM E/R

License plate lamp is not turned ON

• License plate lamp power supply/

ground circuit

• License plate lamp bulb
• License plate lamp bulb socket/

harness

License plate lamp circuit
Refer to 

EXL-173, "Component Func-

tion Check"

.

Parking lamp, license plate lamp, side marker lamp and 
tail lamp are not turned ON

Symptom diagnosis

“PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT 
TURNED ON”
Refer to 

EXL-200, "Diagnosis Procedure"

.

Position lamp indicator is not turned ON
(Parking lamp, license plate lamp, side marker lamp 
and tail lamp are turned ON)

Combination meter

• Combination meter

Data monitor “LIGHT IND”

• BCM (HEAD LAMP)

Active test “TAIL LAMP”

Daytime running light is not turned ON [Headlamp (HI) 
at approximately half illumination]
[Headlamp (HI) is turned ON]

• Fuse
• Daytime running light relay power 

supply/control signal circuit

• Daytime running light relay
• IPDM E/R
• BCM
• ECM
• Combination meter

• Daytime running light relay circuit

Refer to 

EXL-175, "Component 

Function Check"

.

• BCM (HEAD LAMP)

Data monitor “ENGINE STATE”

• Combination meter

Data monitor “PKB SW”

Front fog lamp is not turned 
ON

One side

• Front fog lamp power supply/

ground circuit

• Front fog lamp bulb
• IPDM E/R

Front fog lamp circuit
Refer to 

EXL-180, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis

“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to 

EXL-201, "Diagnosis Procedure"

.

Symptom

Possible cause

Inspection item

Revision: November 2015

2016 JUKE

EXL-194

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

NISMO MODELS

NOTE:

Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any

DTC is detected.

Turn signal lamp does not 
blink

Indicator lamp is normal
(Applicable side per-
forms high flasher activa-
tion)

• Front turn signal lamp
- Front turn signal lamp power sup-

ply/ground circuit

- Front turn signal lamp bulb 
- Front turn signal lamp bulb socket
- BCM
• Side turn signal lamp
- Side turn signal lamp power sup-

ply/ground circuit

- Side turn signal lamp
- BCM
• Rear turn signal lamp
- Rear turn signal lamp power sup-

ply/ground circuit

- Rear turn signal lamp bulb 
- Rear turn signal lamp bulb socket/

harness

- BCM

Turn signal lamp circuit
Refer to 

EXL-182, "Component Func-

tion Check"

.

Indicator lamp is included

• Combination switch input/output 

signal circuit

• Combination switch
• BCM

Combination switch
Refer to 

BCS-92, "Symptom Table"

.

Turn signal indicator lamp 
does not blink
(Turn signal lamp is normal)

One side

Combination meter

—

Both sides
(Always)

• Turn indicator signal
• BCM
• Combination meter

• Combination meter 

Data monitor “TURN IND”

• BCM (FLASHER)

Active test “FLASHER”

Both sides
(Only when activating 
hazard warning lamp 
with ignition switch OFF)

• Combination meter power supply/

ground circuit

• Combination meter

Combination meter
Power supply and ground circuit
Refer to 

MWI-53, "COMBINATION 

METER : Diagnosis Procedure"

.

• Hazard warning lamp does not activate

(Turn signal is normal)

• Hazard warning lamp continues activating

• Hazard switch signal/ground cir-

cuit

• Hazard switch
• BCM

Hazard switch
Refer to 

EXL-188, "Component Func-

tion Check"

.

Symptom

Possible cause

Inspection item

Symptom

Possible cause

Inspection item

Headlamp (HI) is not turned 
ON

One side

• Fuse
• Headlamp (HI) power supply/

ground circuit

• Headlamp (HI) bulb
• Headlamp assembly
- Harness
• IPDM E/R

Headlamp (HI) circuit
Refer to 

EXL-162, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis

 “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to 

EXL-198, "Diagnosis Procedure"

.

High beam indicator lamp is not turned ON
[Headlamp (HI) is turned ON]

Combination meter

• Combination meter

Data monitor “HI-BEAM IND”

• BCM (HEAD LAMP)

Active test “HEAD LAMP”

Revision: November 2015

2016 JUKE

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-195

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Headlamp (LO) is not 
turned ON

One side

• Fuse
• Headlamp (LO) power supply/

ground circuit

• Headlamp (LO) bulb

(Xenon bulb)

• Headlamp assembly
- HID control unit
- Xenon bulb socket
- Harness
• IPDM E/R

Headlamp (LO) circuit
Refer to 

EXL-165, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis

“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to 

EXL-199, "Diagnosis Procedure"

.

Parking lamp is not turned ON

• Parking lamp power supply/

ground circuit

• Front combination lamp
- LED  (Parking  lamp)
- Harness
• IPDM E/R

Parking lamp circuit
Refer to 

EXL-167, "Component Func-

tion Check"

.

Front side marker lamp is not turned ON

• Front side marker lamp power 

supply/ground circuit

• Front side marker lamp bulb
• Front side marker lamp bulb sock-

et

Front side marker lamp circuit
Refer to 

EXL-169, "Component Func-

tion Check"

.

Tail lamp is not turned ON

Stop lamp / Tail lamp 
(Bulb side)

• Fuse
• Tail lamp power supply/ground 

circuit

• Stop lamp / Tail lamp bulb 
• Stop lamp / Tail lamp bulb socket/

harness

• IPDM E/R

Tail lamp circuit
Refer to 

EXL-171, "Component Func-

tion Check"

.

Tail lamp (LED side)

• Fuse
• Tail lamp power supply/ground 

circuit

• Rear combination lamp internal 

circuit

- LED  (Tail  lamp)
• Tail lamp harness
• IPDM E/R

License plate lamp is not turned ON

• License plate lamp power supply/

ground circuit

• License plate lamp bulb
• License plate lamp bulb socket/

harness

License plate lamp circuit
Refer to 

EXL-173, "Component Func-

tion Check"

.

Parking lamp, license plate lamp, side marker lamp and 
tail lamp are not turned ON

Symptom diagnosis

“PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT 
TURNED ON”
Refer to 

EXL-200, "Diagnosis Procedure"

.

Position lamp indicator is not turned ON
(Parking lamp, license plate lamp, side marker lamp 
and tail lamp are turned ON)

Combination meter

• Combination meter

Data monitor “LIGHT IND”

• BCM (HEAD LAMP)

Active test “TAIL LAMP”

Daytime running light is not turned ON

• Fuse
• Daytime running light power sup-

ply/ground circuit

• Daytime running light
• IPDM E/R
• BCM
• ECM
• Combination meter

• Daytime running light circuit

Refer to 

EXL-178, "Component 

Function Check"

.

• BCM (HEAD LAMP)

Data monitor “ENGINE STATE”

• Combination meter

Data monitor “PKB SW”

Symptom

Possible cause

Inspection item

Revision: November 2015

2016 JUKE

EXL-196

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

Turn signal lamp does not 
blink

Indicator lamp is normal
(Applicable side per-
forms high flasher activa-
tion)

• Front turn signal lamp
- Front turn signal lamp power sup-

ply/ground circuit

- Front turn signal lamp bulb 
- Front turn signal lamp bulb socket
- BCM
• Side turn signal lamp
- Side turn signal lamp power sup-

ply/ground circuit

- Side turn signal lamp
- BCM
• Rear turn signal lamp
- Rear turn signal lamp power sup-

ply/ground circuit

- Rear turn signal lamp bulb 
- Rear turn signal lamp bulb socket/

harness

- BCM

Turn signal lamp circuit
Refer to 

EXL-182, "Component Func-

tion Check"

.

Indicator lamp is included

• Combination switch input/output 

signal circuit

• Combination switch
• BCM

Combination switch
Refer to 

BCS-92, "Symptom Table"

.

Turn signal indicator lamp 
does not blink
(Turn signal lamp is normal)

One side

Combination meter

—

Both sides
(Always)

• Turn indicator signal
• BCM
• Combination meter

• Combination meter 

Data monitor “TURN IND”

• BCM (FLASHER)

Active test “FLASHER”

Both sides
(Only when activating 
hazard warning lamp 
with ignition switch OFF)

• Combination meter power supply/

ground circuit

• Combination meter

Combination meter
Power supply and ground circuit
Refer to 

MWI-53, "COMBINATION 

METER : Diagnosis Procedure"

.

• Hazard warning lamp does not activate

(Turn signal is normal)

• Hazard warning lamp continues activating

• Hazard switch signal/ground cir-

cuit

• Hazard switch
• BCM

Hazard switch
Refer to 

EXL-188, "Component Func-

tion Check"

.

Symptom

Possible cause

Inspection item

Revision: November 2015

2016 JUKE

NORMAL OPERATING CONDITION

EXL-197

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

NORMAL OPERATING CONDITION

Description

INFOID:0000000012201768

AUTO LIGHT SYSTEM

The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel,

sky bridge, shadowed area, etc.) while using the auto light system. This is caused by for the control difference.

This is normal.

Revision: November 2015

2016 JUKE