Nissan Juke (2016 year). Service Repair Manual - part 364

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     362      363      364      365     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 364

 

 

EXL-134

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

DIAGNOSIS SYSTEM (BCM)

*

1

: For models without auto light system, this item cannot be monitored.

*

2

: For models without front fog lamp, this item cannot be monitored.

ACTIVE TEST

TURN SIGNAL R
[On/Off]

Each switch status that BCM judges from the combination switch reading function

TURN SIGNAL L
[On/Off]

TAIL LAMP SW
[On/Off]

HI BEAM SW
[On/Off]

HEAD LAMP SW 1
[On/Off]

HEAD LAMP SW 2
[On/Off]

PASSING SW
[On/Off]

AUTO LIGHT SW*

1

[On/Off]

FR FOG SW*

2

[On/Off]

DOOR SW-DR
[On/Off]

Indicated [On/Off] condition of front door switch (driver side)

DOOR SW-AS
[On/Off]

Indicated [On/Off] condition of front door switch (passenger side)

DOOR SW-RR
[On/Off]

Indicated [On/Off] condition of rear door switch RH

DOOR SW-RL
[On/Off]

Indicated [On/Off] condition of rear door switch LH

DOOR SW-BK
[On/Off]

Indicated [On/Off] condition of back door switch

OPTI SEN (DTCT)
[V]

The value of outside brightness voltage input from the optical sensor

OPTI SEN (FILT)
[V]

The value of outside brightness voltage filtered by BCM

OPTICAL SENSOR
[On/Off/NG]

NOTE:

This item cannot be monitored

Monitor item

[Unit]

Description

Test item

Operation

Description

TAIL LAMP

On

• Transmits the position light request signal to IPDM E/R via CAN communication to 

turn the parking, license plate and tail lamps ON

• Transmits the position light request signal to combination meter via CAN commu-

nication to turn the position lamp indicator lamp ON

Off

Stops the position light request signal transmission

HEAD LAMP

HI

• Transmits the high beam request signal to IPDM E/R via CAN communication to 

turn the headlamp (HI) ON

• Transmits the high beam request signal to combination meter via CAN communi-

cation to turn the high beam indicator lamp ON

Low

Transmits the low beam request signal to IPDM E/R via CAN communication to turn 
the headlamp (LO) ON

Off

Stops the high beam request signal and low beam request signal transmission

Revision: November 2015

2016 JUKE

DIAGNOSIS SYSTEM (BCM)

EXL-135

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

*

1

: For models without front fog lamp and except for NISMO models with daytime running light system, this

item cannot be tested.
*

2

: For models without daytime running light system and NISMO models with daytime running light system,

this item cannot be tested.

FLASHER
FLASHER : CONSULT Function (BCM - FLASHER) (HALOGEN TYPE)

INFOID:0000000012201735

WORK SUPPORT

*: Factory setting

DATA MONITOR

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable

to this vehicle, refer to CONSULT display items.

FR FOG LAMP*

1

On

• Transmits the front fog light request signal to IPDM E/R via CAN communication 

to turn the front fog lamp ON (With front fog lamp)

• Transmits the daytime running light request signal to IPDM E/R via CAN commu-

nication to turn the daytime running light ON (NISMO models with daytime running 
light system)

Off

• Stops the front fog light request signal transmission (With front fog lamp)
• Stops the front fog light request signal transmission (NISMO models with daytime 

running light system)

DAYTIME RUNNING LIGHT*

2

On

Transmits the daytime running light request signal to IPDM E/R via CAN communi-
cation to turn the headlamp (HI) ON [Headlamp (HI) at approximately half illumina-
tion]

Off

Stops the daytime running light request signal transmission

ILL DIM SIGNAL

On

NOTE:

This item cannot be tested

Off

Test item

Operation

Description

Service item

Setting item

Setting

HAZARD ANSWER BACK

Lock
Only

With locking only

Sets the hazard warning lamp answer back function when 
the door is lock/unlock with the door request switch and In-
telligent Key

Unlock

Only

With unlocking only

Lock/

Unlock*

With locking/unlocking

Off

Without the function

Monitor item

[Unit]

Description

REQ SW -DR
[On/Off]

Indicates [On/Off] condition of door request switch (driver side)

REQ SW -AS
[On/Off]

Indicates [On/Off] condition of door request switch (passenger side)

PUSH SW
[On/Off]

Indicates [On/Off] condition of push-button ignition switch

TURN SIGNAL R
[On/Off]

Each switch status that BCM detects from the combination switch reading function

TURN SIGNAL L
[On/Off]

HAZARD SW
[On/Off]

The switch status input from the hazard switch

Revision: November 2015

2016 JUKE

EXL-136

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

DIAGNOSIS SYSTEM (BCM)

*: For models without panic alarm function, this item cannot be used.

ACTIVE TEST

RKE-LOCK
[On/Off]

Indicates [On/Off] condition of LOCK signal from Intelligent Key

RKE-UNLOCK
[On/Off]

Indicates [On/Off] condition of UNLOCK signal from Intelligent Key

RKE-PANIC*
[On/Off]

Indicates [On/Off] condition of PANIC button of Intelligent Key

Monitor item

[Unit]

Description

Test item

Operation

Description

FLASHER

RH

• Outputs voltage to turn the right side turn signal lamps ON
• Transmits the turn indicator signal to combination meter via CAN communication 

to turn the turn signal indicator lamp (RH) ON

LH

• Outputs voltage to turn the left side turn signal lamps ON
• Transmits the turn indicator signal to combination meter via CAN communication 

to turn the turn signal indicator lamp (LH) ON

Off

• Stops the voltage to turn the turn signal lamps OFF
• Stops the turn indicator signal transmission

Revision: November 2015

2016 JUKE

DIAGNOSIS SYSTEM (IPDM E/R)

EXL-137

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

DIAGNOSIS SYSTEM (IPDM E/R)

Diagnosis Description

INFOID:0000000012962266

AUTO ACTIVE TEST

Description

In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.

• Rear window defogger

• Front wiper motor

• Parking lamp

• License plate lamp

• Tail lamp

• Side marker lamp

• Front fog lamp

• Headlamp (LO, HI)

• A/C compressor (magnet clutch)

• Cooling fan

Operation Procedure

CAUTION:

Wiper arm interferes with hood when wiper is operated while wiper arm is in the raised position.

Always perform auto active test without setting wiper arm in the raised position. Always pour water on

front windshield glass in advance to auto active test so that damage on front windshield glass surface

is prevented.

1. Turn the ignition switch OFF.
2. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the

ignition switch OFF.

CAUTION:

Close passenger door.

3. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test

starts.

CAUTION:

Engine starts when ignition switch is turned ON while brake pedal is depressed.

4. After a series of the following operations is repeated 3 times, auto active test is completed.

NOTE:

• When auto active test mode has to be cancelled halfway through test, turn the ignition switch OFF.

• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to 

DLK-77,

"Component Function Check"

.

Inspection in Auto Active Test Mode

When auto active test mode is actuated, the following operation sequence is repeated 3 times.

Operation 
sequence

Inspection location

Operation

1

Rear window defogger

10 seconds

2

Front wiper motor

LO for 5 seconds 

 HI for 5 seconds

3

• Parking  lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp

10 seconds

4

Headlamp

LO for 10 seconds 

HI ON 

 OFF 5 times

5

A/C compressor (magnet clutch) ON 

 OFF 5 times

6

Cooling fan

50% duty for 5 seconds 

 100% duty for 5 seconds

Revision: November 2015

2016 JUKE

EXL-138

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

DIAGNOSIS SYSTEM (IPDM E/R)

Concept of auto active test

• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-

tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto

active test starts successfully.

• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.

Diagnosis chart in auto active test mode

JMMIA0588GB

Symptom

Inspection contents

Possible cause

Rear window defogger does not operate

Perform auto active test.
Does the rear window defog-
ger operate?

YES

BCM signal input circuit

NO

• Rear window defogger
• Rear window defogger ground circuit
• Harness or connector between IPDM E/R 

and rear window defogger

• IPDM E/R

Any of the following components do not 
operate

• Parking  lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
• Headlamp (HI, LO)
• Front wiper motor

Perform auto active test.
Does the applicable system 
operate?

YES

BCM signal input circuit

NO

• Lamp or motor
• Lamp or motor ground circuit
• Harness or connector between IPDM E/R 

and applicable system

• IPDM E/R

A/C compressor does not operate

Perform auto active test.
Does the magnet clutch oper-
ate?

YES

• A/C amp. signal input circuit
• CAN communication signal between A/C 

amp. and ECM

• CAN communication signal between ECM 

and IPDM E/R

NO

• Magnet clutch
• Harness or connector between IPDM E/R 

and magnet clutch

• IPDM E/R

Revision: November 2015

2016 JUKE

DIAGNOSIS SYSTEM (IPDM E/R)

EXL-139

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

CONSULT Function (IPDM E/R)

INFOID:0000000012962267

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with IPDM E/R.

SELF DIAGNOSTIC RESULT

Refer to 

PCS-24, "DTC Index"

.

DATA MONITOR

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable

to this vehicle, refer to CONSULT display items.

Cooling fan does not operate

Perform auto active test.
Does the cooling fan operate?

YES

• ECM signal input circuit
• CAN communication signal between ECM 

and IPDM E/R

NO

• Harness or connector between IPDM E/R 

and cooling fan relay

• Harness or connector between IPDM E/R 

and cooling fan control module.

• Harness or connector between cooling fan 

control module and cooling fan motor 

• Cooling fan motor
• Cooling fan relay
• Cooling fan control module
• IPDM E/R

Symptom

Inspection contents

Possible cause

Diagnosis mode

Description

Ecu Identification

Allows confirmation of IPDM E/R part number.

Self Diagnostic Result

Displays the diagnosis results judged by IPDM E/R.

Data Monitor

Displays the real-time input/output data from IPDM E/R input/output data.

Active Test

IPDM E/R can provide a drive signal to electronic components to check their operations.

CAN Diag Support Monitor

The results of transmit/receive diagnosis of CAN communication can be read.

Monitor Item

[Unit]

MAIN 

SIGNALS

Description

RAD FAN REQ
[%]

×

Displays the value of the cooling fan speed request signal received from ECM via CAN 
communication.

AC COMP REQ
[Off/On]

×

Displays the status of the A/C compressor request signal received from ECM via CAN 
communication.

TAIL&CLR REQ
[Off/On]

×

Displays the status of the position light request signal received from BCM via CAN 
communication.

HL LO REQ
[Off/On]

×

Displays the status of the low beam request signal received from BCM via CAN com-
munication.

HL HI REQ
[Off/On]

×

Displays the status of the high beam request signal received from BCM via CAN com-
munication.

FR FOG REQ
[Off/On]

×

Displays the status of the front fog light request signal received from BCM via CAN 
communication.

FR WIP REQ
[Stop/1LOW/Low/Hi]

×

Displays the status of the front wiper request signal received from BCM via CAN com-
munication.

WIP AUTO STOP
[STOP P/ACT P]

×

Displays the status of the front wiper auto stop signal judged by IPDM E/R.

WIP PROT
[Off/BLOCK]

×

Displays the status of the front wiper fail-safe operation judged by IPDM E/R.

IGN RLY1 -REQ
[Off/On]

Displays the status of the ignition switch ON signal received from BCM via CAN com-
munication.

Revision: November 2015

2016 JUKE

EXL-140

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

DIAGNOSIS SYSTEM (IPDM E/R)

ACTIVE TEST

Test item

IGN RLY
[Off/On]

×

Displays the status of the ignition relay judged by IPDM E/R.

PUSH SW
[Off/On]

Displays the status of the push-button ignition switch judged by IPDM E/R.

INTER/NP SW
[Off/On]

Displays the status of the ignition power supply (M/T models) or shift position (CVT 
models) judged by IPDM E/R.

ST RLY CONT
[Off/On]

Displays the status of the starter relay status signal received from BCM via CAN com-
munication.

IHBT RLY -REQ
[Off/On]

Displays the status of the starter control relay signal received from BCM via CAN com-
munication.

ST/INHI RLY
[Off/ ST ON/INHI ON/UNKWN]

Displays the status of the starter relay and starter control relay judged by IPDM E/R.

DETENT SW
[Off/On]

Displays the status of the CVT shift selector (detention switch) judged by IPDM E/R.

S/L RLY -REQ
[Off/On]

NOTE:

This item is indicated, but not monitored.

S/L STATE
[LOCK/UNLK/UNKWN]

NOTE:

This item is indicated, but not monitored.

DTRL REQ
[Off/On]

Displays the status of the daytime running light request signal received from BCM via 
CAN communication.

NOTE:

This item is monitored only for the except for NISMO models.

OIL P SW
[Open/Close]

NOTE:

This item is indicated, but not monitored.

HOOD SW
[Off/On]

NOTE:

This item is indicated, but not monitored.

HL WASHER REQ
[Off/On]

NOTE:

This item is indicated, but not monitored.

THFT HRN REQ
[Off/On]

Displays the status of the theft warning horn request signal received from BCM via 
CAN communication.

HORN CHIRP
[Off/On]

Displays the status of the horn reminder request signal received from BCM via CAN 
communication.

Monitor Item

[Unit]

MAIN 

SIGNALS

Description

Test item

Operation

Description

HORN

On

Operates horn relay for 20 ms.

REAR DEFOGGER

Off

OFF

On

Operates the rear window defogger relay.

FRONT WIPER

Off

OFF

Lo

Operates the front wiper relay.

Hi

Operates the front wiper relay and front wiper high relay.

MOTOR FAN

1

OFF

2

Transmits 50% pulse duty signal (PWM signal) to the cooling fan control module.

3

Transmits 75% pulse duty signal (PWM signal) to the cooling fan control module.

4

Transmits 100% pulse duty signal (PWM signal) to the cooling fan control module.

HEAD LAMP WASHER

On

NOTE:

This item is indicated, but cannot be tested.

Revision: November 2015

2016 JUKE

DIAGNOSIS SYSTEM (IPDM E/R)

EXL-141

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

EXTERNAL LAMPS

Off

OFF

TAIL

Operates the tail lamp relay.

Lo

Operates the headlamp low relay.

Hi

Operates the headlamp low relay and ON/OFF the headlamp high relay at 1 second 
intervals.

Fog

Operates the front fog lamp relay.

Test item

Operation

Description

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     362      363      364      365     ..