Nissan Juke (2016 year). Service Repair Manual - part 363

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     361      362      363      364     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 363

 

 

EXL-126

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

SYSTEM

DAYTIME RUNNING LIGHT SYSTEM : System Diagram

INFOID:0000000012201721

EXCEPT FOR NISMO MODELS

NISMO MODELS

DAYTIME RUNNING LIGHT SYSTEM : System Description

INFOID:0000000012201722

OUTLINE

Except for NISMO Models

• Turns the headlamp (HI) ON [Headlamp (HI) at approximately half illumination] as the daytime running light.

• Daytime running light is controlled by daytime running light control function and combination switch reading

function of BCM, and relay control function of IPDM E/R.

NISMO Models

Daytime running light is controlled by daytime running light control function and combination switch reading

function of BCM, and relay control function of IPDM E/R.

DAYTIME RUNNING LIGHT OPERATION 

Except for NISMO Models

• BCM detects the combination switch condition by the combination switch reading function.

• BCM detects vehicle condition depending on the following signals.

- Engine status signal (received from ECM via CAN communication)

- Parking brake switch signal (received from combination meter via CAN communication)

• BCM transmits the daytime running light request signal to IPDM E/R via CAN communication according to

the daytime running light ON condition.

Daytime running light ON condition

- Engine running with the parking brake released, and any following conditions are satisfied.

JMLIA6141GB

JMLIA3997GB

Revision: November 2015

2016 JUKE

SYSTEM

EXL-127

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

• Lighting switch OFF

• Lighting switch 1ST

• IPDM E/R controls the daytime running light relay (ground-side) to turn ON according to the daytime running

light request signal.

• Power is supplied from the daytime running light relay through headlamp high RH and IPDM E/R to head-

lamp high LH. And high beam headlamps are illuminated (approximately half illumination) as the daytime

running light.

NISMO Models

• BCM detects the combination switch condition by the combination switch reading function.

• BCM detects vehicle condition depending on the following signals.

- Engine status signal (received from ECM via CAN communication)

- Parking brake switch signal (received from combination meter via CAN communication)

• BCM transmits the daytime running light request signal to IPDM E/R via CAN communication according to

the daytime running light ON condition.

Daytime running light ON condition

- Engine running with the parking brake released, and any following conditions are satisfied.

• Lighting switch OFF

• Lighting switch 1ST

• IPDM E/R turns the integrated daytime running light relay ON, and turns the daytime running light ON

according to the daytime running light request signal.

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM
TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Diagram

INFOID:0000000012201723

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Description

INFOID:0000000012201724

OUTLINE

Turn signal lamp and hazard warning lamp is controlled by combination switch reading function and the flasher

control function of BCM.

TURN SIGNAL LAMP OPERATION

• BCM detects the combination switch condition by the combination switch reading function.

• BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is ON and the turn

signal switch is in the right (left) position. BCM blinks the turn signal lamp.

HAZARD WARNING LAMP OPERATION

BCM supplies voltage to both turn signal lamp circuits when the hazard switch is ON. BCM blinks the hazard

warning lamp.

TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL SOUND OPERATION

• BCM transmits the turn indicator signal to the combination meter using CAN communication while the turn

signal lamp and the hazard warning lamp are operating.

JMLIA3117GB

Revision: November 2015

2016 JUKE

EXL-128

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

SYSTEM

• Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal

indicator lamp according to the turn indicator signal.

3-TIME FLASHER FUNCTION

• By a short touch of the turn signal lever, BCM blinks the turn signal lamps 3 times in the selected direction.

• Cancels the operation when short touch of the turn signal lever in the reverse direction during the 3-time

flasher function operation.

HIGH FLASHER OPERATION

• BCM detects the turn signal lamp circuit status from the current value.

• BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn sig-

nal lamp operating.

NOTE:

The blinking speed is normal while operating the hazard warning lamp.

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM : System Di-
agram

INFOID:0000000012201725

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM : System De-
scription

INFOID:0000000012201726

OUTLINE

Parking, license plate, side marker and tail lamps are controlled by combination switch reading function and

parking, license plate, side marker and tail lamps control function of BCM, and relay control function of IPDM

E/R.

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS OPERATION 

• BCM detects the combination switch condition by the combination switch reading function.

• BCM transmits the position light request signal to IPDM E/R and the combination meter via CAN communi-

cation according to the parking, license plate, side marker and tail lamps ON condition.

Parking, license plate, side marker and tail lamps ON condition (When any of the following conditions are satisfied)

- Lighting switch 1ST

- Lighting switch 2ND

- Lighting switch AUTO (Only when the illumination judgment by auto light system is ON. For details, refer to

EXL-124, "AUTO LIGHT SYSTEM : System Description"

.)

• IPDM E/R turns the integrated tail lamp relay ON and turns the parking, license plate and tail lamps ON

according to the position light request signal.

• Combination meter turns the tail lamp indicator lamp ON according to the position light request signal.

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM : Fail-Safe

INFOID:0000000012201727

CAN COMMUNICATION CONTROL

JMLIA2550GB

Revision: November 2015

2016 JUKE

SYSTEM

EXL-129

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

When CAN communication with BCM is impossible, IPDM E/R performs fail-safe control. After CAN communi-

cation recovers normally, it also returns to normal control.

If No CAN Communication Is Available With BCM

FRONT FOG LAMP SYSTEM
FRONT FOG LAMP SYSTEM : System Diagram

INFOID:0000000012201728

FRONT FOG LAMP SYSTEM : System Description

INFOID:0000000012201729

OUTLINE

Front fog lamp is controlled by combination switch reading function and front fog lamp control function of BCM,

and relay control function of IPDM E/R.

FRONT FOG LAMP OPERATION 

• BCM detects the combination switch condition by the combination switch reading function.

• BCM transmits the front fog light request signal to IPDM E/R via CAN communication according to the front

fog lamp ON condition.

Front fog lamp ON condition

- Front fog lamp switch ON, and any of the following conditions are satisfied. [Except headlamp (HI) ON con-

dition]

• Lighting switch 2ND

• Lighting switch AUTO (Only when the illumination judgment by auto light system is ON. For details, refer to

EXL-124, "AUTO LIGHT SYSTEM : System Description"

.)

• IPDM E/R turns the integrated front fog lamp relay ON, and turns the front fog lamp ON according to the

front fog light request signal.

FRONT FOG LAMP SYSTEM : Fail-Safe

INFOID:0000000012201730

CAN COMMUNICATION CONTROL

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN

communication recovers normally, it also returns to normal control.

If No CAN Communication Is Available With BCM

EXTERIOR LAMP BATTERY SAVER SYSTEM

Control part

Fail-safe operation

• Parking lamp
• License plate lamp
• Tail  lamp

• Turns ON the tail lamp relay when the ignition switch is turned ON
• Turns OFF the tail lamp relay when the ignition switch is turned OFF

JMLIA1154GB

Control part

Fail-safe operation

Front fog lamp

Front fog lamp relay OFF

Revision: November 2015

2016 JUKE

EXL-130

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

SYSTEM

EXTERIOR LAMP BATTERY SAVER SYSTEM : System Diagram

INFOID:0000000012201731

EXTERIOR LAMP BATTERY SAVER SYSTEM : System Description

INFOID:0000000012201732

OUTLINE

• Exterior lamp battery saver system is controlled by combination switch reading function and exterior lamp

battery saver function of BCM, and relay control function of IPDM E/R.

• BCM turns the exterior lamp* OFF, according to the vehicle status when ignition switch is turned OFF while

exterior lamp is ON, for preventing battery discharge.

*: Headlamp (LO/HI), front fog lamp, parking lamp, license plate lamp, side marker lamp and tail lamp

EXTERIOR LAMP BATTERY SAVER ACTIVATION

• BCM activates the timer and turns the exterior lamp OFF 45 seconds after the ignition switch is turned from

ON 

 OFF with the exterior lamps ON. 

• When in any of following conditions (after the exterior lamp battery saver is activated), exterior lamps can be

turned ON. 

- Ignition switch is turned from OFF 

 ON

- Lighting switch is changed

- Front fog lamp switch is changed

JMLIA5953GB

Revision: November 2015

2016 JUKE

DIAGNOSIS SYSTEM (BCM)

EXL-131

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

DIAGNOSIS SYSTEM (BCM)

COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)

INFOID:0000000012962265

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.

NOTE:

It can perform the diagnosis modes except the following for all sub system selection items.

×

: Applicable item

NOTE:

*: For models with automatic A/C, this diagnosis mode is not used.

FREEZE FRAME DATA (FFD)

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on

CONSULT.

Diagnosis mode

Function Description

Work Support

Changes the setting for each system function.

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from BCM.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Ecu Identification

The BCM part number is displayed.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

Work Support

Data Monitor

Active Test

Door lock

DOOR LOCK

×

×

×

Rear window defogger

REAR DEFOGGER

×

×

Warning chime

BUZZER

×

×

Interior room lamp timer

INT LAMP

×

×

×

Exterior lamp

HEAD LAMP

×

×

×

Wiper and washer

WIPER

×

×

×

Turn signal and hazard warning lamps

FLASHER

×

×

×

Air conditioning system

AIR CONDITONER

×

×

*

• Intelligent Key system
• Engine start system

INTELLIGENT KEY

×

×

×

Combination switch

COMB SW

×

Body control system

BCM

×

NVIS - NATS

IMMU

×

×

×

Interior room lamp battery saver

BATTERY SAVER

×

×

×

Back door open

TRUNK

×

Theft warning alarm

THEFT ALM

×

×

×

RAP

RETAINED PWR

×

Signal buffer system

SIGNAL BUFFER

×

×

TPMS

AIR PRESSURE MONITOR

×

×

×

Revision: November 2015

2016 JUKE

EXL-132

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

DIAGNOSIS SYSTEM (BCM)

NOTE:

*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position (A/T models
and CVT models), and any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.

HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (HALOGEN TYPE)

INFOID:0000000012201734

WORK SUPPORT

CONSULT screen item

Indication/Unit

Description

Vehicle Speed

km/h

Vehicle speed of the moment a particular DTC is detected

Odo/Trip Meter

km

Total mileage (Odometer value) of the moment a particular DTC is detected

Vehicle Condition

SLEEP>LOCK

Power position status of 
the moment a particular 
DTC is detected

While turning BCM status from low power consumption mode to 
normal mode (Power position is “LOCK”*.)

SLEEP>OFF

While turning BCM status from low power consumption mode to 
normal mode (Power position is “OFF”.)

LOCK>ACC

While turning power position from “LOCK”* *to “ACC”

ACC>ON

While turning power position from “ACC” to “IGN”

RUN>ACC

While turning power position from “RUN” to “ACC” (Vehicle is 
stopping and selector lever is except P position.)

CRANK>RUN

While turning power position from “CRANKING” to “RUN” (From 
cranking up the engine to run it)

RUN>URGENT

While turning power position from “RUN“ to “ACC” (Emergency 
stop operation)

ACC>OFF

While turning power position from “ACC” to “OFF”

OFF>LOCK

While turning power position from “OFF” to “LOCK”*

OFF>ACC

While turning power position from “OFF” to “ACC”

ON>CRANK

While turning power position from “IGN” to “CRANKING”

OFF>SLEEP

While turning BCM status from normal mode (Power position is 
“OFF”.) to low power consumption mode

LOCK>SLEEP

While turning BCM status from normal mode (Power position is 
“LOCK”*.) to low power consumption mode

LOCK

Power position is “LOCK”*

OFF

Power position is “OFF” (Ignition switch OFF)

ACC

Power position is “ACC” (Ignition switch ACC)

ON

Power position is “IGN” (Ignition switch ON with engine stopped)

ENGINE RUN

Power position is “RUN” (Ignition switch ON with engine running)

CRANKING

Power position is “CRANKING” (At engine cranking)

IGN Counter

0 - 39

The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1 

 2 

 3...38 

 39 after returning to the normal condition 

whenever ignition switch OFF 

 ON.

• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.

Revision: November 2015

2016 JUKE

DIAGNOSIS SYSTEM (BCM)

EXL-133

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

*

1

: For models without auto light system, this item cannot be used.

*

2

: Factory setting

DATA MONITOR

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable

to this vehicle, refer to CONSULT display items.

Service item

Setting item

Setting

CUSTOM A/LIGHT SETTING*

1

MODE1*

2

Normal

MODE2

More sensitive setting than normal setting (Turns ON earlier than normal operation)

MODE3

More sensitive setting than MODE2 (Turns ON earlier than MODE2)

MODE4

Less sensitive setting than normal setting (Turns ON later than normal operation)

BATTERY SAVER SET

On*

2

With the exterior lamp battery saver function

Off

Without the exterior lamp battery saver function

ILL DELAY SET*

1

MODE1*

2

45 sec.

Sets delay timer function timer operation time.
(All doors closed)

MODE2

Without the function

MODE3

30 sec.

MODE4

60 sec.

MODE5

90 sec.

MODE6

120 sec.

MODE7

150 sec.

MODE8

180 sec.

HEAD LIGHT TIMER

MODE1

10 sec.

Sets follow me home function activating time

MODE2*

2

30 sec.

AUTO LIGHT LOGIC SET*

1

MODE1*

2

With twilight ON custom & with wiper INT, LO and HI

MODE2

With twilight ON custom & with wiper LO and HI

MODE3

With twilight ON custom & without

MODE4

Without twilight ON custom & with wiper INT, LO and HI

MODE5

Without twilight ON custom & with wiper LO and HI

MODE6

Without twilight ON custom & without

Monitor item

[Unit]

Description

PUSH SW
[On/Off]

Indicates [On/Off] condition of push-button ignition switch

ENGINE STATE
[STOP/STALL/CRANK/RUN]

Indicates [STOP/STALL/CRANK/RUN] condition of engine states

VEH SPEED 1
[km/h]

Display the vehicle speed signal received from combination meter by numerical value [km/h]

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     361      362      363      364     ..