Nissan Juke (2016 year). Service Repair Manual - part 354

EXL-54

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

HEADLAMP (LO) CIRCUIT

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK HEADLAMP (LO) GROUND CIRCUIT

Check continuity between headlamp harness connector and ground.

Is the inspection result normal?

YES

>> Perform the xenon headlamp diagnosis. Refer to 

EXL-55, "Diagnosis Procedure"

.

NO

>> Repair or replace harness.

IPDM E/R

Headlamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E15

52

E55

4

Existed

LH

51

E54

Headlamp

—

Continuity

Connector

Terminal

RH

E55

2

Ground

Existed

LH

E54

Revision: November 2015

2016 JUKE

XENON HEADLAMP

EXL-55

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

XENON HEADLAMP

Diagnosis Procedure

INFOID:0000000012201641

1.

CHECK XENON BULB

Install the normal bulb to the applicable headlamp. Check that the headlamp (LO) is turned ON.
Is the headlamp (LO) turned ON?

YES

>> Replace the corresponding xenon bulb. Refer to 

EXL-96, "Replacement"

.

NO

>> GO TO 2.

2.

CHECK XENON HEADLAMP

Install the normal headlamp assembly to the applicable headlamp. Check that the headlamp (LO) is turned

ON.
Is the headlamp (LO) turned ON?

YES

>> Replace the corresponding headlamp assembly. Refer to 

EXL-96, "Removal and Installation"

.

NO

>> Xenon headlamp is normal.

Revision: November 2015

2016 JUKE

EXL-56

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

PARKING LAMP CIRCUIT

PARKING LAMP CIRCUIT

Component Function Check

INFOID:0000000012201642

1.

CHECK TAIL LAMP OPERATION

Check that the tail lamp is turned ON.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check tail lamp circuit. Refer to 

EXL-60, "Component Function Check"

.

2.

CHECK PARKING LAMP OPERATION

With CONSULT

1. Turn ignition switch ON.

2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

3. With operating the test items, check that the parking lamp is turned ON.

Without CONSULT

1. Start IPDM E/R auto active test. Refer to 

PCS-12, "Diagnosis Description"

.

2. Check that the parking lamp is turned ON.
Is the inspection result normal?

YES

>> Parking lamp circuit is normal.

NO

>> Refer to 

EXL-56, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201643

1.

CHECK PARKING LAMP POWER SUPPLY

With CONSULT

1. Turn ignition switch ON.

2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

3. With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

2.

CHECK PARKING LAMP POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector and parking lamp connector.

3. Check continuity between IPDM E/R harness connector and parking lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

TAIL

: Parking lamp ON

Off

: Parking lamp OFF

+

-

Test item

Voltage

IPDM E/R

Connector

Terminal

E14

43

Ground

EXTERNAL 
LAMPS

TAIL

9 – 16 V

Off

0 – 1 V

IPDM E/R

Parking lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E14

43

E44

1

Existed

LH

E28

Revision: November 2015

2016 JUKE

PARKING LAMP CIRCUIT

EXL-57

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

NO

>> Repair or replace harness.

3.

CHECK PARKING LAMP GROUND CIRCUIT

Check continuity between parking lamp harness connector and ground.

Is the inspection result normal?

YES

>> Replace the corresponding front combination lamp. Refer to 

EXL-100, "Removal and Installation"

.

NO

>> Repair or replace harness.

Parking lamp

—

Continuity

Connector

Terminal

RH

E44

2

Ground

Existed

LH

E28

Revision: November 2015

2016 JUKE

EXL-58

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

FRONT SIDE MARKER LAMP CIRCUIT

FRONT SIDE MARKER LAMP CIRCUIT

Component Function Check

INFOID:0000000012201644

1.

CHECK PARKING LAMP OPERATION

Check that the parking lamp is turned ON.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check parking lamp circuit. Refer to 

EXL-56, "Component Function Check"

.

2.

CHECK FRONT SIDE MARKER LAMP OPERATION

With CONSULT

1. Turn ignition switch ON.

2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

3. With operating the test items, check that the front side marker lamp is turned ON.

Without CONSULT

1. Start IPDM E/R auto active test. Refer to 

PCS-12, "Diagnosis Description"

.

2. Check that the front side marker lamp is turned ON.
Is the inspection result normal?

YES

>> Front side marker lamp circuit is normal.

NO

>> Refer to 

EXL-58, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201645

1.

CHECK FRONT SIDE MARKER LAMP POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector and front side marker lamp connector.

3. Check continuity between IPDM E/R harness connector and front side marker lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK FRONT SIDE MARKER LAMP GROUND CIRCUIT

Check continuity between front side marker lamp harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK FRONT SIDE MARKER LAMP BULB

Check the applicable front side marker lamp bulb.

TAIL

: Front side marker lamp ON

Off

: Front side marker lamp OFF

IPDM E/R

Front side marker lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E14

43

E32

1

Existed

LH

E31

Front side marker lamp

—

Continuity

Connector

Terminal

RH

E32

2

Ground

Existed

LH

E31

Revision: November 2015

2016 JUKE

FRONT SIDE MARKER LAMP CIRCUIT

EXL-59

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Is the inspection result normal?

YES

>> Check the corresponding front side marker lamp bulb socket. Repair or replace if necessary.

NO

>> Replace the corresponding front side marker lamp bulb. Refer to 

EXL-100, "Replacement"

.

Revision: November 2015

2016 JUKE

EXL-60

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

TAIL LAMP CIRCUIT

TAIL LAMP CIRCUIT

Component Function Check

INFOID:0000000012201646

1.

CHECK TAIL LAMP OPERATION

With CONSULT

1. Turn ignition switch ON.

2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

3. With operating the test items, check that the tail lamp is turned ON.

Without CONSULT

1. Start IPDM E/R auto active test. Refer to 

PCS-12, "Diagnosis Description"

.

2. Check that the tail lamp is turned ON.
Is the inspection result normal?

YES

>> Tail lamp circuit is normal.

NO

>> Refer to 

EXL-60, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201647

1.

CHECK FUSE

1. Turn ignition switch OFF.

2. Check that the following fuse is not blown (open).

Is the fuse blown (open)?

YES

>> Replace the blown fuse after repairing the affected circuit if a fuse is blown (open).

NO

>> GO TO 2.

2.

CHECK TAIL LAMP POWER SUPPLY

With CONSULT

1. Turn ignition switch ON.

2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

3. With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

3.

CHECK TAIL LAMP POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

TAIL

: Tail lamp ON

Off

: Tail lamp OFF

Unit

Location

Fuse No.

Capacity

• Parking  lamp  RH
• Parking lamp LH
• Front side marker lamp RH
• Front side marker lamp LH
• Tail  lamp  RH
• Tail  lamp  LH
• License plate lamp RH
• License plate lamp LH

IPDM E/R

#47

10 A

+

-

Test item

Voltage

IPDM E/R

Connector

Terminal

E14

44

Ground

EXTERNAL 
LAMPS

TAIL

9 – 16 V

Off

0 – 1 V

Revision: November 2015

2016 JUKE

TAIL LAMP CIRCUIT

EXL-61

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

2. Disconnect IPDM E/R connector and rear combination lamp connector.

3. Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK TAIL LAMP GROUND CIRCUIT

Check continuity between rear combination lamp harness connector and ground.

Is the inspection result normal?

YES-1 >> Stop lamp / tail lamp (Bulb side): GO TO 5.

YES-2 >> Tail lamp (LED side): Check the corresponding tail lamp harness, and if check result is normal,

replace the corresponding rear combination lamp. Refer to 

EXL-109, "Removal and Installation"

.

NO

>> Repair or replace harness.

5.

CHECK STOP LAMP / TAIL LAMP BULB

Check the applicable stop lamp / tail lamp bulb.
Is the inspection result normal?

YES

>> Check the corresponding stop lamp / tail lamp bulb socket and harness. Repair or replace if nec-

essary.

NO

>> Repair or replace the corresponding stop lamp / tail lamp bulb. Refer to 

EXL-109, "Replacement"

.

IPDM E/R

Rear combination lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E14

44

B59

2

Existed

LH

B80

Rear combination lamp

—

Continuity

Connector

Terminal

RH

B59

3

Ground

Existed

LH

B80

Revision: November 2015

2016 JUKE