Nissan Juke (2016 year). Service Repair Manual - part 310

EM-36

< REMOVAL AND INSTALLATION >

[MR FOR NISMO RS MODELS]

CATALYST

• Tighten in numerical order as shown in the figure.

- Install catalyst converter (base on stud position 1).

- Temporary assemble 2 (no priority).

- Temporary assemble 3, 4.

- Tightening 5, 6 and 7.

- Tightening again 8, 9 and 10.

- Temporary assemble 11.

- Tightening 12,13,14,and 15.

3. Note the following, and install in the reverse order of removal.

A/F sensor 1

• Using heated oxygen sensor wrench [SST: KV10117100 (J-3647-A)], install A/F sensor 1.

CAUTION:

• Before installing a new sensors, clean exhaust system threads using heated oxygen sensor

thread cleaner tool (Commercial Service Tool: J-43897-18 or J-43897-12) and apply anti-seize

lubricant. 

• Never apply excessive torque to sensor 2. Doing so may cause damage to sensor 2, resulting

in the “MIL” illuminating.

• Prevent rust preventives from adhering to the sensor body.

AWD

JPBIA4362GB

Revision: November 2015

2016 JUKE

CATALYST

EM-37

< REMOVAL AND INSTALLATION >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EM

N

P

O

AWD : Exploded View

INFOID:0000000012197263

AWD : Removal and Installation

INFOID:0000000012197264

REMOVAL

1. Remove engine cover. Refer to 

EM-26, "Exploded View"

.

2. Remove cowl top extension. Refer to 

EXT-29, "Exploded View"

.

3. Remove air duct (suction side). Refer to 

EM-27, "Exploded View"

.

4. Remove air inlet tube 3. Refer to 

EM-32, "Exploded View"

.

5. Remove front tube. Refer to 

EX-5, "Exploded View"

.

6. Remove heat insulator. Refer to 

FAX-43, "AWD : Exploded View"

.

7. Remove catalyst converter support bracket (upper and lower).
8. Remove A/F sensor 1 and heated oxygen sensor 2.

• Use heated oxygen sensor wrench [SST: KV10117100 (J-3647-A)], remove A/F sensor 1 and heated

oxygen sensor 2.

CAUTION:

JPBIA4345GB

1.

A/F sensor 1

2.

Catalyst converter shroud upper

3.

Gasket

4.

Heated oxygen sensor 2

5.

Catalyst converter support bracket 
(lower)

6.

Catalyst converter

7.

Catalyst converter support bracket 
(upper)

A.

To exhaust system
Engine front

 : N·m (kg-m, ft-lb)

 : N·m (kg-m, in-lb)

 : Always replace after every disassembly.

,   : Indicates that the parts is connected at points with same symbols in actual vehicle.

Revision: November 2015

2016 JUKE

EM-38

< REMOVAL AND INSTALLATION >

[MR FOR NISMO RS MODELS]

CATALYST

• Never damage air fuel ratio sensor 1 and heated oxygen sensor 2.

• Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a

hard surface such as a concrete floor; use a new one.

9. Remove catalyst converter shroud upper.
10. Remove bolts and nut of catalyst converter turbocharger side. 
11. Remove catalyst convertor. And keep a service area.

NOTE:

Slide the catalyst converter in a lateral direction to obtain work space for removing exhaust manifold

mounting nuts.

12. Remove heat insulator. Refer to 

EM-40, "Exploded View"

.

13. Disconnect water hoses from turbocharger as follows:

• Attach plug to prevent engine coolant leakage when engine coolant is not drained.

CAUTION:

Perform this step when the engine is cold.

14. Remove oil supply tube and oil return pipe. Refer to 

EM-40, "Exploded View"

.

15. Remove exhaust manifold cover. Refer to 

EM-44, "Exploded View"

.

16. Remove exhaust manifold mounting nuts.
17. Remove exhaust manifold with turbocharger.
18. Remove gasket of exhaust manifold.
19. Remove catalyst converter.
20. Remove gasket.

INSTALLATION

1. Install gasket between turbocharger and catalyst as shown in

the figure.

2. Install catalyst converter with the following procedure. 

1

:  Gasket

A

: Turbocharger side

B

: Catalyst converter side

C

:  Claw

JPBIA4418ZZ

Revision: November 2015

2016 JUKE

CATALYST

EM-39

< REMOVAL AND INSTALLATION >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EM

N

P

O

• Tighten in numerical order as shown in the figure.

- Install catalyst converter (base on stud position 1).

- Temporary assemble 2 (no priority).

- Temporary assemble 3, 4.

- Tightening 5, 6 and 7.

- Tightening again 8, 9 and 10.

- Temporary assemble 11.

- Tightening 12,13,14,and 15.

3. Note the following, and install in the reverse order of removal.

A/F sensor 1 and Heated oxygen sensor 2

 

• Using heated oxygen sensor wrench [SST: KV10117100 (J-

3647-A)], install A/F sensor 1 and heated oxygen sensor 2.

CAUTION:

• Before installing a new sensors, clean exhaust system

threads using heated oxygen sensor thread cleaner tool

(Commercial Service Tool: J-43897-18 or J-43897-12)

and apply anti-seize lubricant. 

• Never apply excessive torque to sensors. Doing so may

cause damage to sensors, resulting in the “MIL” illumi-

nating.

• Prevent rust preventives from adhering to the sensor

body.

JPBIA4371GB

Revision: November 2015

2016 JUKE

EM-40

< REMOVAL AND INSTALLATION >

[MR FOR NISMO RS MODELS]

TURBOCHARGER

TURBOCHARGER

Exploded View

INFOID:0000000012197265

Removal and Installation

INFOID:0000000012197266

REMOVAL

1.

Heat insulator

2.

Actuator hose

3.

Clamp

4.

Turbocharger inlet tube

5.

Gasket

6.

Gasket

7.

Clamp

8.

Oil outlet hose

9.

Oil return pipe

10. Oil supply tube

11. O-ring

12. Gasket

13. Turbocharger

14. Eye bolt

15. Gasket

16. Oil supply tube
A.

To boost control solenoid valve

B.

To air inlet hose

C.

To PCV hose

D.

To air duct

E.

To air inlet tube assembly

F.

To catalyst converter

 : N·m (kg-m, ft-lb)

 : N·m (kg-m, in-lb)

 : Always replace after every disassembly.

JSBIA1974GB

Revision: November 2015

2016 JUKE

TURBOCHARGER

EM-41

< REMOVAL AND INSTALLATION >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EM

N

P

O

1. Remove engine cover. Refer to 

EM-26, "Exploded View"

.

2. Remove cowl top extension. Refer to 

EXT-29, "Exploded View"

.

3. Remove air duct (suction side). Refer to 

EM-27, "Exploded View"

.

4. Remove air inlet tube 3. Refer to 

EM-32, "Exploded View"

.

5. Remove front tube. Refer to 

EX-5, "Exploded View"

.

6. Remove heat insulator. Refer to 

FAX-27, "2WD : Exploded View"

 (2WD models) or 

FAX-43, "AWD :

Exploded View"

 (AWD models).

7. Remove catalyst converter support bracket (upper and lower).
8. Remove A/F sensor 1.

• Using heated oxygen sensor wrench [SST: KV10117100 (J-3647-A)], remove A/F sensor 1.

CAUTION:

• Discard any A/F sensor 1 which has been dropped from a height of more than 0.5 m (19.7 in)

onto a hard surface such as a concrete floor; use a new one.

• Before installing new A/F sensor 1, clean exhaust system threads using Oxygen Sensor

Thread Cleaner [commercial service tool (J-43897-18 or J-43897-12)] and approved Anti-seize

Lubricant (commercial service tool).

9. Remove catalyst converter shroud upper.
10. Disconnect heated oxygen sensor 2 harness connector. (AWD models)
11. Remove bolts and nut of catalyst converter turbocharger side. 
12. Remove catalyst convertor. And keep a service area.

NOTE:

Slide the catalyst converter in a lateral direction to obtain work space for removing turbocharger.

13. Remove gasket of catalyst converter.
14. Remove exhaust manifold cover. Refer to 

EM-44, "Exploded View"

.

15. Remove turbocharger assembly as follows:
a. Remove heat insulator.
b. Disconnect water hose from turbocharger. Refer to 

EM-29, "Exploded View"

.

• Attach plug to prevent engine coolant leakage when engine coolant is not drained.

CAUTION:

Perform this step when the engine is cold.

c. Remove oil supply tube and oil return pipe.
d. Remove mounting nuts of turbocharger.

CAUTION:

Never deform each turbocharger piping when pulling out the assembly.

INSTALLATION

CAUTION:

Do not reuse O-rings.

Install in the reverse order of removal.

Inspection

INFOID:0000000012197267

INSPECTION PROCERDURE

Trouble Diagnosis of Turbocharger

Check items before trouble diagnosis 
1. Check that the engine oil level is between L (Low level) and H (High level) of the oil level gauge. [When

the engine oil amount is more then H (High level), the engine oil flows into the inlet duct through the blow-

by gas passage, and the turbocharger is misjudged failure.] 

2. Ask the customer if he/she always runs the vehicle in idle engine speed to cool the engine oil down after

driving.

• Replace the exhaust manifold and turbocharger assembly when any malfunction is found after unit

inspections specified in the table below.

• If no malfunction is found after the unit inspections, judge that the turbocharger body has no non-stan-

dard conditions. Check the other parts again.

Revision: November 2015

2016 JUKE

EM-42

< REMOVAL AND INSTALLATION >

[MR FOR NISMO RS MODELS]

TURBOCHARGER

INSPECTION AFTER REMOVAL

Turbocharger

Turbocharger

CAUTION:

When the compressor wheel, turbine wheel or rotor shaft is damaged, remove all the fragments and

foreign matter left in the following passages in order to prevent a secondary failure:

Inspection Location

Result

Symptoms likely to occur when the results shown on 

the left exist.

Oil leakage

Smoke

Noise

Poor pow-

er

Poor ac-

celeration

Turbine wheel

Wet with oil.

C

A

C

C

Carbon deposits observed.

C

A

B

B

“Rubs against” housing.

C

B

A

B

Vane is bent or broken.

A

A

Compressor wheel

Inside of intake port is badly stained 
with oil.

B

B

“Rubs against” housing.

C

B

A

B

Vane is bent or broken.

A

A

Check both turbine and compres-
sor rotor shaft end play.

Heavy feel or catching when turned by 
hand.

C

C

B

Cannot be turned by hand.

A

Excessively loose bearing.

C

C

B

C

Rotor shaft, oil return port (Check 
inside using penlight.)

Carbon or sludge deposits in oil drain 
port.

C

A

C

C

Boost control valve actuator oper-
ation (using a handy pump)

• Does not operate smoothly when air 

pressure is gradually applied.

• Stroke amount is not compliance 

with the air pressure.

A

A: Highly 

possible.

B: Possible.

C: May 

exist.

JPBIA4359ZZ

A.

Check for leakage

Revision: November 2015

2016 JUKE

TURBOCHARGER

EM-43

< REMOVAL AND INSTALLATION >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EM

N

P

O

Turbocharger Boost Control

• Connect the a pressurized handy pump (A) to the actuator, and

check that the rod strokes smoothly in compliance with the follow-

ing pressure.

INSPECTION AFTER INSTALLATION

Start engine and raise engine speed to check no exhaust emission leaks.

Suction side

: Between turbocharger and charge air cooler

Exhaust side

: Between turbocharger and outlet duct

Standard (value of pressure/Value of rod moving): 

Refer to 

EM-140, "Turbocharger"

.

JPBIA0665ZZ

Revision: November 2015

2016 JUKE