Content .. 306 307 308 309 ..

Nissan Juke (2016 year). Service Repair Manual - part 308

EM-20

< PERIODIC MAINTENANCE >

[MR FOR NISMO RS MODELS]

DRIVE BELT

PERIODIC MAINTENANCE

DRIVE BELT

Exploded View

INFOID:0000000012197240

Removal and Installation

INFOID:0000000012197241

REMOVAL

1. Turn the steering wheel to the right.
2. Remove the front fender protector (RH) front side bolts and clips. And keep a service area. Refer to

EXT-

31, "Exploded View"

3. Hold the hexagonal part (A) of drive belt auto-tensioner (1) with

a wrench securely. Then move the wrench handle in the direc-

tion of arrow (loosening direction of tensioner).

CAUTION:

Avoid placing hand in a location where pinching may occur

if the holding tool accidentally comes off.

4. Insert a rod approximately 6 mm (0.24 in) in diameter such as

short-length screwdriver into the hole (B) of the retaining boss to

fix drive belt auto-tensioner.

• Keep drive belt auto-tensioner pulley arm locked after drive

belt is removed.

5. Remove drive belt.

INSTALLATION

1. Install drive belt.

CAUTION:

• Confirm drive belt is completely set to pulleys.

• Check for engine oil, working fluid and engine coolant are not adhered to drive belt and each

pulley groove.

2. Release drive belt auto-tensioner, and apply tension to drive belt.
3. Turn crankshaft pulley clockwise several times to equalize tension between each pulley.
4. Confirm tension of drive belt at indicator (notch on fixed side) is within the possible use range. Refer to

EM-20, "Exploded View"

Alternator

Drive belt auto-tensioner

Crankshaft pulley

A/C compressor

Water pump

Drive belt

Possible use range

Range when new drive belt is in-
stalled

Indicator

JPBIA4302ZZ

JPBIA4351ZZ

Revision: November 2015

2016 JUKE

DRIVE BELT

EM-21

< PERIODIC MAINTENANCE >

[MR FOR NISMO RS MODELS]

Inspection

INFOID:0000000012197242

WARNING:

Perform this step when engine is stopped.

• Check that the indicator (C) (notch on fixed side) of drive belt auto-tensioner is within the possible use range

(A) in the figure.

NOTE:

• Check the drive belt auto-tensioner indication when the engine is cold.

• When new drive belt is installed, the indicator (notch on fixed side) should be within the range (B) in the fig-

ure.

• Visually check entire drive belt for wear, damage or cracks.

• If the indicator (notch on fixed side) is out of the possible use range or belt is damaged, replace drive belt.

Adjustment

INFOID:0000000012197243

Alternator

Drive belt auto-tensioner

Crankshaft pulley

A/C compressor

Water pump

Drive belt

Possible use range

Range when new drive belt is in-
stalled

Indicator

JPBIA4302ZZ

Refer to :

EM-139, "Drive Belt"

Revision: November 2015

2016 JUKE

EM-22

< PERIODIC MAINTENANCE >

[MR FOR NISMO RS MODELS]

AIR CLEANER FILTER

AIR CLEANER FILTER

Exploded View

INFOID:0000000012197244

Removal and Installation

INFOID:0000000012197245

REMOVAL

Mass air flow sensor

Gasket

Clamp

Air duct (suction side)

Clamp

Air cleaner cover assembly

Mounting rubber

Air cleaner filter

Air cleaner body assembly

10. Air duct inlet (lower)

11. Grommet

12. Air duct inlet (upper)

13. Grommet

14. Bracket

15. Mounting rubber

To turbocharger

: N·m (kg-m, in-lb)

: Always replace after every disassembly.

JPBIA4305GB

Revision: November 2015

2016 JUKE

AIR CLEANER FILTER

EM-23

< PERIODIC MAINTENANCE >

[MR FOR NISMO RS MODELS]

1. Remove air duct inlet (upper) (1).
2. Unhook the tabs (A) of both ends of the air cleaner cover.

3. Remove the air cleaner filter (1) and air cleaner body (2) from

the air cleaner case.

4. Remove the air cleaner filter from the air cleaner body.

INSTALLATION

Note the following, and install in the reverse order of removal.

• Fixing clips shall be fixed after inserting air cleaner body protrusion to air cleaner case notch hole.

• Make sure that whether air cleaner body has been firmly installed by shaking it.

Inspection (Viscous Paper Type)

INFOID:0000000012197246

INSPECTION AFTER REMOVAL

Examine with eyes that there is no stain, clogging, or damage on air cleaner element.

• Remove dusts (such as dead leafs) on air cleaner element surface and inside cleaner case.

• If clogging or damage is observed, replace the air cleaner element.

CAUTION:

Never clean the viscous paper type air cleaner element by blowing as there is a risk of deterioration of

its performance

MAINTENANCE INTERVAL

Refer to

MA-7, "Introduction of Periodic Maintenance"

JPBIA4352ZZ

JPBIA4353ZZ

Revision: November 2015

2016 JUKE

EM-24

< PERIODIC MAINTENANCE >

[MR FOR NISMO RS MODELS]

SPARK PLUG

SPARK PLUG

Exploded View

INFOID:0000000012197247

Removal and Installation

INFOID:0000000012197248

REMOVAL

1. Remove engine cover. Refer to

EM-26, "Exploded View"

2. Remove air inlet tube assembly. Refer to

EM-32, "Exploded View"

3. Remove ignition coil.

Rocker cover protector

O-ring

PCV valve

PCV hose

Clamp

Rocker cover gasket

Rocker cover

Clamp

PCV hose

10. Oil filler cap

11. Spark plug

12. Ignition coil

To intake manifold

Comply with the assembly procedure
when tightening. Refer to

EM-60

To air duct

: N·m (kg-m, ft-lb)

: N·m (kg-m, in-lb)

: Always replace after every disassembly.

JPBIA4303GB

Revision: November 2015

2016 JUKE

SPARK PLUG

EM-25

< PERIODIC MAINTENANCE >

[MR FOR NISMO RS MODELS]

4. Remove spark plug with a spark plug wrench (commercial ser-

vice tool).

CAUTION:

Never drop or shock spark plug.

INSTALLATION

Install in the reverse order of removal.

Inspection

INFOID:0000000012197249

INSPECTION AFTER REMOVAL

Use the standard type spark plug for normal condition.

CAUTION:

• Never drop or shock spark plug.

• Never use a wire brush for cleaning.

• If plug tip is covered with carbon, spark plug cleaner may be

used.

•

Spark plug gap adjustment is not required between replace-

ment intervals.

•

Measure spark plug gap. when it exceeds the limit, replace

spark plug even if it is with in the specified replacement mile-

age. Refer to

EM-139, "Spark Plug"

: 14 mm (0.55 in)

JPBIA0030ZZ

Spark plug (Standard type)

: Refer to

EM-139, "Spark Plug"

Cleaner air pressure : Less than 588 kPa (6 kg/cm

85 psi)

Cleaning time

: Less than 20 seconds

SMA773C

JPBIA0031ZZ

Revision: November 2015

2016 JUKE

EM-26

< REMOVAL AND INSTALLATION >

[MR FOR NISMO RS MODELS]

ENGINE COVER

REMOVAL AND INSTALLATION

ENGINE COVER

Exploded View

INFOID:0000000012197250

Removal and Installation

INFOID:0000000012197251

REMOVAL

Remove engine cover.

CAUTION:

Never damage or scratch engine cover when installing or removing.

INSTALLATION

Install in the reverse order of removal.

Engine cover

Mounting rubber (Black)

Mounting rubber (Gray)

JPBIA4311ZZ

Revision: November 2015

2016 JUKE

AIR CLEANER AND AIR DUCT

EM-27

< REMOVAL AND INSTALLATION >

[MR FOR NISMO RS MODELS]

AIR CLEANER AND AIR DUCT

Exploded View

INFOID:0000000012197252

Removal and Installation

INFOID:0000000012197253

REMOVAL

NOTE:

Mass air flow sensor is removable under the car-mounted condition.
1. Remove engine cover. Refer to

EM-26, "Exploded View"

2. Remove air duct inlet (upper).
3. Remove the air cleaner filter from the air cleaner case.
4. Disconnect mass air flow sensor harness connector, and remove harness clamp from air cleaner body.
5. Remove air cleaner body assembly.
6. Remove the air duct (suction side).

• Add matching marks if necessary for easier installation.

Mass air flow sensor

Gasket

Clamp

Air duct (suction side)

Clamp

Air cleaner cover assembly

Mounting rubber

Air cleaner filter

Air cleaner body assembly

10. Air duct inlet (lower)

11. Grommet

12. Air duct inlet (upper)

13. Grommet

14. Bracket

15. Mounting rubber

To turbocharger

: N·m (kg-m, in-lb)

: Always replace after every disassembly.

JPBIA4305GB

Revision: November 2015

2016 JUKE

Content .. 306 307 308 309 ..