Nissan Juke (2016 year). Service Repair Manual - part 294

P2263 TC SYSTEM

EC-1167

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Check the exhaust manifold and turbocharger assembly. Refer to 

EM-244, "Inspection"

.

Is the inspection result normal?

YES

>> CHECK INTERMITTENT INCIDENT. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Replace exhaust manifold and turbocharger assembly. Refer to 

EM-242, "Exploded View"

.

Component Inspection (Turbocharger Bypass Control Valve)

INFOID:0000000012198687

1.

CHECK TURBOCHARGER BYPASS CONTROL VALVE

With consult

1. Turn ignition switch ON and engine stopped or engine running (idling, less than 1200rpm).

2. On the CONSULT screen, select ENGINE » ACTIVE TEST »“TC BYPASS VALVE”.

3. Operate “ON” or “OFF” and check if valve operating sound can be heard.

Without consult

1. Turn ignition switch OFF.

2. Disconnect turbocharger bypass control valve harness connector.

3. Apply a voltage of 12V to the positive or negative terminal.
Can the valve operating sound be heard?

YES

>> INSPECTION END

NO

>> Replace turbocharger assembly (do not replace bypass control valve only). Refer to 

EM-242,

"Exploded View"

.

Component Inspection (Turbocharger Boost Sensor)

INFOID:0000000012198688

1.

CHECK TURBOCHARGER BOOST SENSOR 

1. Turn ignition switch OFF.

2. Remove turbocharger boost sensor with its harness connector.

3. Install pressure pump (A) to turbocharger boost sensor (1).

CAUTION:

When insert a pressure pump hose to the sensor, be careful

to the damage of the sensor housing.

4. Turn ignition switch ON.

5. Check the voltage between ECM harness connector terminals

as per the following conditions.

NOTE:

• Always calibrate the pressure pump gauge when using it.

• Inspection should be done at room temperature [10 - 30

°

C (50 - 86

°

F)].

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace turbocharger boost sensor. Refer to 

EM-194, "Exploded View"

.

JMBIA0871ZZ

ECM

Condition [Pressure (Relative to at-

mospheric pressure)]

Voltage

(Approx.)

Connector

+

−

Terminal

F23

11

13

0 kPa
(0 mbar, 0 mmHg, 0 inHg)

2.03 V

40 kPa
(400 mbar, 300 mmHg, 11.81 inHg)

2.67 V

Revision: November 2015

2016 JUKE

EC-1168

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

P2562, P2566 WASTEGATE CONTROL VALVE POSITION SENSOR

P2562, P2566 WASTEGATE CONTROL VALVE POSITION SENSOR

DTC Logic

INFOID:0000000012198693

DTC DETECTION LOGIC

NOTE:

If DTC P2562 or P2566 is displayed with DTC P0643 first perform the trouble diagnosis for DTC P0643. Refer

to 

EC-1060, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure

before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start the engine and let it idle for 10 seconds.

2. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-1168, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012198694

1.

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect electric wastegate control actuator harness connector.

3. Turn ignition switch ON.

4. Check the voltage between electric wastegate control actuator harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

DTC No.

Trouble diagnosis name

(Trouble diagnosis content)

DTC detecting condition

Possible Cause

P2562

TC BOOST CONTROL POSI-
TION SEN A
(Turbocharger boost control po-
sition sensor A circuit)

ECM detects the following status continu-
ously for 5 seconds or more:
A voltage signal transmitted from the waste-
gate control valve position sensor is 4.7 V or 
more.

• Harness or connectors

(Wastegate control valve position sen-
sor circuit is open or shorted.)

• Electric wastegate control actuator

P2566

TC BOOST CONTROL POSI-
TION SEN A
(Turbocharger boost control po-
sition sensor A circuit intermit-
tent)

ECM detects the following status continu-
ously for 0.5 seconds or more:
A voltage signal transmitted from the waste-
gate control valve position sensor is 0.25 V 
or less.

+

−

Voltage

(Approx.)

Electric wastegate control actua-

tor

Connector

Terminal

F61

3

Ground

5 V

Revision: November 2015

2016 JUKE

P2562, P2566 WASTEGATE CONTROL VALVE POSITION SENSOR

EC-1169

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

NO

>> Perform the trouble diagnosis for power supply circuit.

2.

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between electric wastegate control actuator harness connector and ECM harness

connector.

4. Also check harness for short to power.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts.

3.

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR INPUT SIGNAL CIRCUIT

1. Check the continuity between electric wastegate control actuator harness connector and ECM harness

connector.

2. Also check harness for short to ground and to power.
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace error-detected parts.

4.

CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR

Check the electric wastegate control actuator. Refer to 

EC-1169, "Component Inspection (Electric Wastegate

Control Actuator)"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Replace electric wastegate control actuator. Refer to 

EC-600, "ENGINE CONTROL SYSTEM :

Component Parts Location"

.

Component Inspection (Electric Wastegate Control Actuator)

INFOID:0000000012198695

1.

INSPECTION START

Do you have CONSULT?
Do you have CONSULT?

YES

>> GO TO 2.

NO

>> GO TO 3.

2.

CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR

With CONSULT

1. Turn ignition switch ON and engine stopped.

2. On the CONSULT screen, select “ENGINE” >> “ACTIVE TEST” >> “WASTEGATE ACTUATOR”.

3. Operate “Up” or “Down”, set “W/G ACTUATOR POSITION B1” to 0.002 m, and make a quick short note of

value “V1” of “W/G ACTUATOR POSI SEN B1”.

+

−

Continuity

Electric wastegate control 

actuator

ECM

Connector

Terminal

Connector

Terminal

F61

2

F24

72

Existed

+

−

Continuity

Electric wastegate control 

actuator

ECM

Connector

Terminal

Connector

Terminal

F61

1

F24

65

Existed

Revision: November 2015

2016 JUKE

EC-1170

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

P2562, P2566 WASTEGATE CONTROL VALVE POSITION SENSOR

4. Operate “Up” or “Down”, set “W/G ACTUATOR POSITION B1” to 0.006 m, and make a quick short note of

value “V2” of “W/G ACTUATOR POSI SEN B1”.

Do the values of “V1” and “V2” change (visually, ACTUATOR SHAFT operates) and “V2” minus “V1” becomes

equal to or more than 1.3V?

YES

>> INSPECTION END

NO

>> Replace Turbocharger Assembly (do not replace electric wastegate control actuator only). Refer

to 

EC-600, "ENGINE CONTROL SYSTEM : Component Parts Location"

.

3.

CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR

Without CONSULT

1. Turn ignition switch OFF.

2. Disconnect Wastegate control actuator harness connector.

3. While checking the POSITION SENSOR OUT voltage with an oscilloscope, apply a voltage of 12 V to the

positive or negative terminal.

Does ACTUATOR SHAFT visually operate and POSITION SENSOR OUT voltage change?

YES

>> INSPECTION END

NO

>> Replace Turbocharger Assembly (do not replace electric wastegate control actuator only). Refer

to 

EC-600, "ENGINE CONTROL SYSTEM : Component Parts Location"

.

Revision: November 2015

2016 JUKE

P2563 WASTEGATE CONTROL VALVE POSITION SENSOR

EC-1171

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P2563 WASTEGATE CONTROL VALVE POSITION SENSOR

DTC Logic

INFOID:0000000012198696

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure

before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start the engine, and warm it up until the following condition is satisfied.

2. Move the vehicle to a cool place.

3. Stop the engine, and cool it down until the following condition is satisfied.

CAUTION:

Never turn ignition switch ON during soaking.

4. Start engine and let it idle for 5 seconds or more.

CAUTION:

Never turn ignition switch OFF during idling.

5. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-1171, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012198697

1.

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect electric wastegate control actuator harness connector.

3. Turn ignition switch ON.

4. Check the voltage between electric wastegate control actuator harness connector and ground.

DTC No.

Trouble diagnosis name

(Trouble diagnosis content)

DTC detecting condition

Possible Cause

P2563

TC BOOST CONTROL POSI-
TION SEN A
(Turbocharger boost control po-
sition sensor A circuit range/per-
formance)

ECM detects the following status when 
ECM operates the fully closed position 
learning of a wastegate control valve imme-
diately after engine cold start:  A voltage 
signal transmitted from the turbocharger 
boost control position sensor is higher than 
1.78 V, or lower than 0.60 V.

Electric wastegate control actuator

Engine coolant temperature 65

°

C (149

°

F) or more

Engine oil temperature

80

°

C (176

°

F) or more

Engine coolant temperature

50

°

C (122

°

F) or less

Engine oil temperature

Revision: November 2015

2016 JUKE

EC-1172

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

P2563 WASTEGATE CONTROL VALVE POSITION SENSOR

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 5.

2.

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between electric wastegate control actuator harness connector and ECM harness

connector.

4. Also check harness for short to power.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts.

3.

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR INPUT SIGNAL CIRCUIT

1. Check the continuity between electric wastegate control actuator harness connector and ECM harness

connector.

2. Also check harness for short to ground and to power.
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace error-detected parts.

4.

CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR

Check the electric wastegate control actuator. Refer to 

EC-1173, "Component Inspection (Electric Wastegate

Control Actuator)"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Replace electric wastegate control actuator. Refer to 

EC-600, "ENGINE CONTROL SYSTEM :

Component Parts Location"

.

5.

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between electric wastegate control actuator harness connector and ECM harness

connector.

+

−

Voltage

(Approx.)

Electric wastegate control actua-

tor

Connector

Terminal

F61

3

Ground

5 V

+

−

Continuity

Electric wastegate control 

actuator

ECM

Connector

Terminal

Connector

Terminal

F61

2

F24

72

Existed

+

−

Continuity

Electric wastegate control 

actuator

ECM

Connector

Terminal

Connector

Terminal

F61

1

F24

65

Existed

Revision: November 2015

2016 JUKE

P2563 WASTEGATE CONTROL VALVE POSITION SENSOR

EC-1173

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

4. Also check harness for short to ground and short to power.
Is the inspection result normal?

YES

>> Perform the trouble diagnosis for ECM power supply circuit. Refer to 

EC-792, "Diagnosis Proce-

dure"

.

NO

>> Repair or replace error-detected parts.

Component Inspection (Electric Wastegate Control Actuator)

INFOID:0000000012198698

1.

INSPECTION START

Do you have CONSULT?
Do you have CONSULT?

YES

>> GO TO 2.

NO

>> GO TO 3.

2.

CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR

With CONSULT

1. Turn ignition switch ON and engine stopped.

2. On the CONSULT screen, select “ENGINE” >> “ACTIVE TEST” >> “WASTEGATE ACTUATOR”.

3. Operate “Up” or “Down”, set “W/G ACTUATOR POSITION B1” to 0.002 m, and make a quick short note of

value of “W/G ACTUATOR POSI SEN B1”. Assume this value to be "V1".

4. Operate “Up” or “Down”, set “W/G ACTUATOR POSITION B1” to 0.006 m, and make a quick short note of

value of “W/G ACTUATOR POSI SEN B1”. Assume this value to be "V2".

Do the values of “V1” and “V2” change (visually, ACTUATOR SHAFT operates) and “V2” minus “V1” becomes

equal to or more than 1.3V?

YES

>> INSPECTION END

NO

>> Replace Turbocharger Assembly (do not replace electric wastegate control actuator only). Refer

to 

EC-600, "ENGINE CONTROL SYSTEM : Component Parts Location"

.

3.

CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR

Without CONSULT

1. Turn ignition switch OFF.

2. Disconnect Wastegate control actuator harness connector.

3. While checking the POSITION SENSOR OUT voltage with an oscilloscope, apply a voltage of 12 V to the

positive or negative terminal.

Does ACTUATOR SHAFT visually operate and POSITION SENSOR OUT voltage change?

YES

>> INSPECTION END

NO

>> Replace Turbocharger Assembly (do not replace electric wastegate control actuator only). Refer

to 

EC-600, "ENGINE CONTROL SYSTEM : Component Parts Location"

.

Electric wastegate control 

actuator

ECM

Continuity

Connector

Terminal

Connector

Terminal

F61

3

F24

61

Existed

Revision: November 2015

2016 JUKE

EC-1174

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

P2564, P2565 WASTEGATE CONTROL VALVE POSITION SENSOR

P2564, P2565 WASTEGATE CONTROL VALVE POSITION SENSOR

DTC Logic

INFOID:0000000012198699

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure

before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON and wait at least 10 seconds.

2. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-1174, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012198700

1.

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect electric wastegate control actuator harness connector.

3. Turn ignition switch ON.

4. Check the voltage between electric wastegate control actuator harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 5.

2.

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

DTC No.

Trouble diagnosis name

(Trouble diagnosis content)

DTC detecting condition

Possible Cause

P2564

TC BOOST CONTROL POSI-
TION SEN A
(Turbocharger boost control po-
sition sensor A circuit low)

ECM detects the following status continu-
ously for 5 seconds or more:  A voltage sig-
nal transmitted from the wastegate control 
valve position sensor is 0.25 V or less.

• Harness or connectors

(Wastegate control valve position sen-
sor circuit is open or shorted.)

• Electric wastegate control actuator

P2565

TC BOOST CONTROL POSI-
TION SEN A
(Turbocharger boost control po-
sition sensor A circuit high)

ECM detects the following status continu-
ously for 5 seconds or more:  A voltage sig-
nal transmitted from the wastegate control 
valve position sensor is 4.63 V or more.

+

−

Voltage

(Approx.)

Electric wastegate control actua-

tor

Connector

Terminal

F61

3

Ground

5 V

Revision: November 2015

2016 JUKE