Nissan Juke (2016 year). Service Repair Manual - part 219

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     217      218      219      220     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 219

 

 

ON BOARD REFUELING VAPOR RECOVERY (ORVR)

EC-567

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace refueling EVAP vapor cut valve with fuel tank .Refer to 

FL-27, "2WD : Exploded View"

.

Component Inspection (Drain filter)

INFOID:0000000012198112

1.

CHECK DRAIN FILTER

1. Check visually for insect nests in the drain filter air inlet.

2. Check visually for cracks or flaws in the appearance.

3. Check visually for cracks or flaws in the hose.

4. Blow air into port A and check that it flows freely out of port B.

5. Block port B.

6. Blow air into port A and check that there is no leakage.
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace drain filter.

1.

Filler tube

2.

Recirculation line

3.

EVAP/ORVR line

4.

Vacuum/pressure handy pump

5.

Fuel tank

JMBIA2315ZZ

PBIB3641E

Revision: November 2015

2016 JUKE

EC-568

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

REFRIGERANT PRESSURE SENSOR

REFRIGERANT PRESSURE SENSOR

Component Function Check

INFOID:0000000012198113

1.

CHECK REFRIGERANT PRESSURE SENSOR OVERALL FUNCTION

1. Start engine and warm it up to normal operating temperature.

2. Turn A/C switch and blower fan switch ON.

3. Check the voltage between ECM harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Proceed to 

EC-568, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012198114

1.

CHECK REFRIGERANT PRESSURE SENSOR POWER SUPPLY

1. Turn ignition OFF.

2. Disconnect refrigerant pressure sensor harness connector.

3. Turn ignition switch ON.

4. Check the voltage between refrigerant pressure sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK REFRIGERANT PRESSURE SENSOR POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between refrigerant pressure sensor harness connector and ECM harness connec-

tor.

4. Also check harness for short to ground.
Is the inspection result normal?

YES

>> Perform the trouble diagnosis for power supply circuit.

NO

>> Repair or replace error-detected parts.

3.

CHECK REFRIGERANT PRESSURE SENSOR GROUND

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between refrigerant pressure sensor harness connector and ECM harness connec-

tor.

ECM

Voltage

Connector

+

−

Terminal

F25

19

12

1.0 - 4.0V

+

−

Voltage

(Approx.)

Refrigerant pressure sensor

Connector

Terminal

E49

3

Ground

5 V

+

−

Continuity

Refrigerant pressure sensor

ECM

Connector

Terminal

Connector

Terminal

E49

3

F25

23

Existed

Revision: November 2015

2016 JUKE

REFRIGERANT PRESSURE SENSOR

EC-569

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

4. Also check harness for short to power.
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace error-detected parts.

4.

CHECK REFRIGERANT PRESSURE SENSOR INPUT SIGNAL CIRCUIT

1. Check the continuity between ECM harness connector and refrigerant pressure sensor harness connec-

tor.

2. Also check harness for short to ground and to power.
Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace error-detected parts.

5.

CHECK INTERMITTENT INCIDENT.

Perform 

GI-45, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace refrigerant pressure sensor. Refer to 

HAC-98, "Exploded View"

.

NO

>> Repair or replace error-detected parts. 

+

−

Continuity

Refrigerant pressure sensor

ECM

Connector

Terminal

Connector

Terminal

E49

1

F25

12

Existed

+

−

Continuity

Refrigerant pressure sensor

ECM

Connector

Terminal

Connector

Terminal

E49

2

F25

19

Existed

Revision: November 2015

2016 JUKE

EC-570

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

BRAKE PEDAL POSITION SWITCH

BRAKE PEDAL POSITION SWITCH

Component Function Check

INFOID:0000000012198115

1.

CHECK BRAKE PEDAL POSITION SWITCH FUNCTION

With CONSULT

1. Turn ignition switch ON.

2. Select “BRAKE SW1” in “DATA MONITOR” mode of “ENGINE” using CONSULT.

3. Check “BRAKE SW1” indication as per the following conditions.

Without CONSULT

1. Turn ignition switch ON.

2. Check the voltage between ECM harness connector terminals as per the following.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Proceed to 

EC-570, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012198116

1.

CHECK BRAKE PEDAL POSITION SWITCH POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect brake pedal position switch harness connector.

3. Turn ignition switch ON.

4. Check the voltage between brake pedal position switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Perform the trouble diagnosis for power supply circuit.

2.

CHECK BRAKE PEDAL POSITION SWITCH INPUT SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between brake pedal position switch harness connector and ECM harness connec-

tor.

Monitor item

Condition

Indication

BRAKE SW1

Brake pedal

Slightly depressed

OFF

Fully released

ON

ECM

Condition

Voltage

(Approx.)

Connector

+

–

Terminal

E18

116

127

Brake pedal

Slightly depressed

0 V

Fully released

Battery voltage

+

−

Voltage

Brake pedal position switch

Connector

Terminal

E112

1

Ground

Battery voltage

+

−

Continuity

Brake pedal position switch

ECM

Connector

Terminal

Connector

Terminal

E112

2

E18

116

Existed

Revision: November 2015

2016 JUKE

BRAKE PEDAL POSITION SWITCH

EC-571

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

4. Also check harness for short to ground and to power.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts.

3.

CHECK BRAKE PEDAL POSITION SWITCH

Check the brake pedal position switch. Refer to 

EC-571, "Component Inspection (Brake Pedal Position

Switch)"

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Replace brake pedal position switch. Refer to 

BR-20, "Exploded View"

.

Component Inspection (Brake Pedal Position Switch)

INFOID:0000000012198117

1.

CHECK BRAKE PEDAL POSITION SWITCH-I

1. Turn ignition switch OFF.

2. Disconnect brake pedal position harness connector.

3. Check the continuity between brake pedal position switch terminals as per the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK BRAKE PEDAL POSITION SWITCH-II

1. Adjust brake pedal position switch installation. Refer to 

BR-9, "Inspection and Adjustment"

.

2. Check the continuity between brake pedal position switch terminals as per the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace brake pedal position switch. Refer to 

BR-20, "Exploded View"

.

Brake pedal position switch

Condition

Continuity

+

−

Terminals

1

 2

Brake pedal

Fully released

Existed

Slightly de-
pressed

Not existed

Brake pedal position switch

Condition

Continuity

+

−

Terminals

1

 2

Brake pedal

Fully released

Existed

Slightly de-
pressed

Not existed

Revision: November 2015

2016 JUKE

EC-572

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

CLUTCH PEDAL POSITION SWITCH

CLUTCH PEDAL POSITION SWITCH

Component Function Check

INFOID:0000000012198118

1.

CHECK FOR CLUTCH PEDAL POSITION SWITCH FUNCTION

1. Turn ignition switch ON.

2. Check the voltage between ECM harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END.

NO

>> Proceed to 

EC-572, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012198119

1.

CHECK CLUTCH PEDAL POSITION INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect clutch pedal position switch harness connector.

3. Turn ignition switch ON.

4. Check the voltage between clutch pedal position switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK CLUTCH PEDAL POSITION SWITCH INPUT SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connectors.

3. Check the continuity between clutch pedal position switch harness connector and ECM harness connec-

tor.

4. Also check harness for short to ground and to power. 
Is the inspection result normal?

YES

>> Perform the trouble diagnosis for power supply circuit.

NO

>> Repair or replace error-detected parts.

3.

CHECK CLUTCH PEDAL POSITION SWITCH GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connectors.

3. Check the continuity between clutch pedal position switch harness connector and ground

ECM

Condition

Voltage

(Approx.)

Connector

+

−

Terminal

E18

108

127

Clutch pedal

Slightly depressed

Battery voltage

Fully released

0V

+

−

Voltage

Clutch pedal position switch

Connector

Terminal

E113

1

Ground

Battery voltage

+

−

Continuity

Clutch pedal position switch

ECM

Connector

Terminal

Connector

Terminal

E113

1

E18

108

Existed

Revision: November 2015

2016 JUKE

CLUTCH PEDAL POSITION SWITCH

EC-573

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

4. Also check harness for short to power. 
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace error-detected parts.

4.

CHECK CLUTCH PEDAL POSITION SWITCH

Check the clutch pedal position switch. Refer to 

EC-573, "Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Replace clutch pedal position switch. Refer to 

CL-11, "Exploded View"

.

Component Inspection

INFOID:0000000012198120

1.

CHECK CLUTCH PEDAL POSITION SWITCH-I

1. Turn ignition switch OFF.

2. Disconnect clutch pedal position switch harness connector.

3. Check the continuity between clutch pedal position switch terminals as per the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK CLUTCH PEDAL POSITION SWITCH-II

1. Adjust clutch pedal position switch installation. Refer to 

CL-12, "Inspection and Adjustment"

.

2. Check the continuity between clutch pedal position switch terminals as per the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace clutch pedal position switch. Refer to 

CL-11, "Exploded View"

.

+

−

Continuity

Clutch pedal position switch

Connector

Terminal

E113

2

Ground

Existed

Clutch pedal position switch

Condition

Continuity

+

−

Terminal

1

2

Clutch pedal

Fully released

Existed

Slightly depressed

Not existed

Clutch pedal position switch

Condition

Continuity

+

−

Terminal

1

2

Clutch pedal

Fully released

Existed

Slightly depressed

Not existed

Revision: November 2015

2016 JUKE

EC-574

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

INFORMATION DISPLAY (ASCD)

INFORMATION DISPLAY (ASCD)

Component Function Check

INFOID:0000000012198121

1.

CHECK INFORMATION DISPLAY

1. Start engine.

2. Press ASCD MAIN switch on ASCD steering switch.

3. Drive the vehicle at more than 40 km/h (25 MPH).

CAUTION:

Always drive vehicle at a safe speed.

4. Press SET/

−

 switch.

5. Check that the reading of the speedometer shows the same value as the set speed indicated in the infor-

mation display while driving the vehicle on a flat road.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Proceed to 

EC-574, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012198122

1.

CHECK DTC

Check that DTC UXXXX, P0500 or P1574 is not displayed.
Is the inspection result normal?

YES

>> GO TO 2.

NO-1 >> Perform trouble diagnosis for DTC UXXXX.

NO-2 >> Perform trouble diagnosis for DTC P0500. Refer to 

EC-397, "EXCEPT FOR M/T MODELS : DTC

Logic"

.

NO-3 >> Perform trouble diagnosis for DTC P1574. Refer to 

EC-480, "DTC Logic"

.

2.

CHECK DTC WITH COMBINATION METER

Refer to 

MWI-22, "CONSULT Function"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Perform trouble diagnosis for DTC indicated.

3.

CHECK INTERMITTENT INCIDENT

Perform 

GI-45, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-64, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     217      218      219      220     ..