Content .. 205 206 207 208 ..

Nissan Juke (2016 year). Service Repair Manual - part 207

P1556, P1557 BATTERY TEMPERATURE SENSOR

EC-471

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

4. Also check harness for short to ground.
Is the inspection result normal?

YES

>> Perform the trouble diagnosis for power supply circuit.

>> Repair or replace error-detected parts.

CHECK BATTERY TEMPERATURE SENSOR GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between battery current sensor harness connector and ECM harness connector.

4. Also check harness for short to power.
Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace error-detected parts.

CHECK BATTERY TEMPERATURE SENSOR

Check the battery temperature sensor. Refer to

EC-471, "Component Inspection"

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

>> Replace battery negative cable assembly. Refer to

PG-106, "Exploded View"

Component Inspection

INFOID:0000000012198024

CHECK BATTERY TEMPERATURE SENSOR

1. Turn ignition switch OFF.

2. Disconnect battery current sensor.

3. Check the resistance between battery current sensor connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

>> Replace battery negative cable assembly. Refer to

PG-106, "Exploded View"

−

Continuity

Battery current sensor

ECM

Connector

Terminal

Connector

Terminal

F52

F26

Existed

−

Continuity

Battery current sensor

ECM

Connector

Terminal

Connector

Terminal

F52

F26

Existed

Battery current sensor

Resistance

−

Terminal

Continuity with the resistance value 100

Ω

or more

Revision: November 2015

2016 JUKE

EC-472

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P1564 ASCD STEERING SWITCH

P1564 ASCD STEERING SWITCH

DTC Logic

INFOID:0000000012198025

DTC DETECTION LOGIC

NOTE:

If DTC P1564 is displayed with DTC P0603, P0604, P0605, P0606, P0607, P060A and P060B first per-

form the trouble diagnosis for DTC P0603, P0604, P0605, P0606, P0607, P060A and P060B. Refer to

EC-115, "DTC Index"

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure

before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Wait at least 10 seconds.

3. Press MAIN switch for at least 10 seconds, then release it and wait at least 10 seconds.

4. Press CANCEL switch for at least 10 seconds, then release it and wait at least 10 seconds.

5. Press ACCEL/RES switch for at least 10 seconds, then release it and wait at least 10 seconds.

6. Press COAST/SET switch for at least 10 seconds, then release it and wait at least 10 seconds.

7. Check DTC.
Is DTC detected?

YES

>> Proceed to

EC-472, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012198026

CHECK ASCD STEERING SWITCH CIRCUIT

With CONSULT

1. Turn ignition switch ON.

2. Select “CANCEL SW”, “RESUME/ACC SW” and “SET SW” in “DATA MONITOR” mode of “ENGINE”

using CONSULT.

3. Check each item indication as per the following conditions.

DTC No.

Trouble diagnosis name

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P1564

ASCD SW
(ASCD steering switch)

• An excessively high voltage signal from the

ASCD steering switch is sent to ECM.

• ECM detects that input signal from the

ASCD steering switch is out of the specified
range.

• ECM detects that the ASCD steering switch

is stuck ON.

• Harness or connectors

(ASCD steering switch circuit is open
or shorted.)

• ASCD steering switch
• ECM

Monitor item

Condition

Indication

MAIN SW

MAIN switch

Pressed

Released

OFF

CANCEL SW

CANCEL switch

Pressed

Released

OFF

Revision: November 2015

2016 JUKE

P1564 ASCD STEERING SWITCH

EC-473

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

Without CONSULT

1. Turn ignition switch ON.

2. Check the voltage between ECM harness connector terminals.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

>> GO TO 2.

CHECK ASCD STEERING SWITCH GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Disconnect combination switch (spiral cable) harness connector.

4. Check the continuity between combination switch (spiral cable) and ECM harness connector.

5. Also check harness for short to ground and to power.
Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace error-detected parts.

CHECK ASCD STEERING SWITCH INPUT SIGNAL CIRCUIT

1. Check the continuity between ECM harness connector and combination switch.

2. Also check harness for short to ground and to power.
Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace error-detected parts.

RESUME/ACC
SW

ACCEL/RES switch

Pressed

Released

OFF

SET SW

COAST/SET switch

Pressed

Released

OFF

Monitor item

Condition

Indication

ECM

Condition

Voltage

(Approx.)

Connector

Terminal

E18

110

111

MAIN switch: Pressed

0 V

CANCEL switch: Pressed

1 V

COAST/SET switch: Pressed

2 V

ACCEL/RES switch: Pressed

3 V

All ASCD steering switches: Released

4 V

−

Continuity

Combination switch

(Spiral cable)

ECM

Connector

Terminal

Connector

Terminal

M33

E18

111

Existed

−

Continuity

Combination switch

(Spiral cable)

ECM

Connector

Terminal

Connector

Terminal

M33

E18

110

Existed

Revision: November 2015

2016 JUKE

EC-474

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P1564 ASCD STEERING SWITCH

CHECK ASCD STEERING SWITCH

Refer to

EC-474, "Component Inspection"

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

>> Replace ASCD steering switch. Refer to

ST-9, "Exploded View"

Component Inspection

INFOID:0000000012198027

CHECK ASCD STEERING SWITCH

1. Disconnect combination switch (spiral cable) harness connector.

2. Check the resistance between combination switch harness connector terminals as per the following condi-

tions.

Is the inspection result normal?

YES

>> INSPECTION END

>> Replace ASCD steering switch. Refer to

ST-9, "Exploded View"

Combination switch

(Spiral cable)

Condition

Resistance

(Approx.)

Connector

−

Terminals

M302

MAIN switch: Pressed

Ω

CANCEL switch: Pressed

250

Ω

COAST/SET switch: Pressed

660

Ω

ACCEL/RES switch: Pressed

1,480

Ω

All ASCD steering switches: Released

4,000

Ω

Revision: November 2015

2016 JUKE

P1572 BRAKE PEDAL POSITION SWITCH

EC-475

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P1572 BRAKE PEDAL POSITION SWITCH

DTC Logic

INFOID:0000000012198028

DTC DETECTION LOGIC

NOTE:

•

If DTC P1572 is displayed with DTC P0603, P0604, P0605, P0606, P0607, P060A and P060B, first per-

form the trouble diagnosis for DTC P0603, P0604, P0605, P0606, P0607, P060A and P060B. Refer to

EC-115, "DTC Index"

•

This self-diagnosis has the one trip detection logic. When malfunction A is detected, DTC is not

stored in ECM memory. And in that case, 1st trip DTC and 1st trip freeze frame data are displayed.

1st trip DTC is erased when ignition switch OFF. And even when malfunction A is detected in two

consecutive trips, DTC is not stored in ECM memory.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure

before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

NOTE:

Procedure for malfunction B is not described here. It takes extremely long time to complete procedure for mal-

function B. By performing procedure for malfunction A, the incident that causes malfunction B can be

detected.

>> GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A

1. Start engine.

2. Press MAIN switch and make sure that CRUISE indicator is displayed in combination meter.

3. Drive the vehicle for at least 5 consecutive seconds as per the following conditions.

CAUTION:

Always drive vehicle at a safe speed.

NOTE:

This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle.

If a road test is expected to be easier, it is unnecessary to lift the vehicle.

4. Check DTC.
Is DTC detected?

YES

>> Proceed to

EC-480, "Diagnosis Procedure"

>> GO TO 3.

DTC No.

Trouble diagnosis

name

(Trouble diagnosis

content)

DTC detecting condition

Possible cause

P1572

ASCD BRAKE SW
(ASCD brake
switch)

When the vehicle speed is above 30 km/h
(19 MPH), ON signals from the stop lamp
switch and the brake pedal position switch
are sent to the ECM at the same time.

• Harness or connectors

(Stop lamp switch circuit is shorted.)
(Brake pedal position switch circuit is shorted.)

• Stop lamp switch
• Brake pedal position switch
• Incorrect stop lamp switch installation
• Incorrect brake pedal position switch installa-

tion

• ECM

Brake pedal position switch signal is not
sent to ECM for extremely long time while
the vehicle is driving.

Vehicle speed

More than 30 km/h (19 mph)

Selector lever

Suitable position

Revision: November 2015

2016 JUKE

EC-476

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P1572 BRAKE PEDAL POSITION SWITCH

PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B

1. Drive the vehicle for at least 5 consecutive seconds as per the following conditions.

CAUTION:

Always drive vehicle at a safe speed.

NOTE:

This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle.

If a road test is expected to be easier, it is unnecessary to lift the vehicle.

2. Check DTC.
Is DTC detected?

YES

>> Proceed to

EC-480, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012198029

CHECK OVERALL FUNCTION-I

With CONSULT

1. Turn ignition switch ON.

2. Select “BRAKE SW1” in “DATA MONITOR” mode of “ENGINE” using CONSULT.

3. Check “BRAKE SW1” indication as per the following conditions.

Without CONSULT

1. Turn ignition switch ON.

2. Check the voltage between ECM harness connector terminals as per the following.

Is the inspection result normal?

YES

>> GO TO 2.

>> GO TO 3.

CHECK OVERALL FUNCTION-II

With CONSULT

Select “BRAKE SW2” and check indication as per the following conditions.

Without CONSULT

Check the voltage between ECM harness connector terminals as per the following conditions.

Vehicle speed

More than 30 km/h (19 mph)

Selector lever

Suitable position

Driving location

Depress the brake pedal for more
than five seconds so as not to come
off from the above-mentioned vehi-
cle speed.

Monitor item

Condition

Indication

BRAKE SW1

Brake pedal

Slightly depressed

OFF

Fully released

ECM

Condition

Voltage

(Approx.)

Connector

–

Terminal

E18

116

127

Brake pedal

Slightly depressed

0 V

Fully released

Battery voltage

Monitor item

Condition

Indication

BRAKE SW2

Brake pedal

Slightly depressed

Fully released

OFF

Revision: November 2015

2016 JUKE

P1572 BRAKE PEDAL POSITION SWITCH

EC-477

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

>> GO TO 6.

CHECK BRAKE PEDAL POSITION SWITCH POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect brake pedal position switch harness connector.

3. Turn ignition switch ON.

4. Check the voltage between brake pedal position switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> Perform the trouble diagnosis for power supply circuit.

CHECK BRAKE PEDAL POSITION SWITCH INPUT SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between brake pedal position switch harness connector and ECM harness connec-

tor.

4. Also check harness for short to ground and to power.
Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace error-detected parts.

CHECK BRAKE PEDAL POSITION SWITCH

Check the brake pedal position switch. Refer to

EC-571, "Component Inspection (Brake Pedal Position

Switch)"

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

>> Replace brake pedal position switch. Refer to

BR-20, "Exploded View"

CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect stop lamp switch harness connector.

3. Check the voltage between stop lamp switch harness connector and ground.

ECM

Condition

Voltage

(Approx.)

Connector

–

Terminal

E18

115

127

Brake pedal

Slightly depressed

Battery voltage

Fully released

0 V

−

Voltage

Brake pedal position switch

Connector

Terminal

E112

Ground

Battery voltage

−

Continuity

Brake pedal position switch

ECM

Connector

Terminal

Connector

Terminal

E112

E18

116

Existed

Revision: November 2015

2016 JUKE

EC-478

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P1572 BRAKE PEDAL POSITION SWITCH

*1: CVT models
*2: M/T models

Is the inspection result normal?

YES

>> GO TO 7.

>> Perform the trouble diagnosis for power supply circuit.

CHECK STOP LAMP SWITCH INPUT SIGNAL CIRCUIT

1. Disconnect ECM harness connector.

2. Check the continuity between stop lamp switch harness connector and ECM harness connector.

*1: CVT models
*2: M/T models

3. Also check harness for short to ground and to power.
Is the inspection result normal?

YES

>> GO TO 8.

>> Repair or replace error-detected parts.

CHECK STOP LAMP SWITCH

Check the stop lamp switch. Refer to

EC-479, "Component Inspection (Stop Lamp Switch)"

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

>> Replace stop lamp switch. Refer to

BR-20, "Exploded View"

Component Inspection (Brake Pedal Position Switch)

INFOID:0000000012198030

CHECK BRAKE PEDAL POSITION SWITCH-I

1. Turn ignition switch OFF.

2. Disconnect brake pedal position harness connector.

3. Check the continuity between brake pedal position switch terminals as per the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

>> GO TO 2.

CHECK BRAKE PEDAL POSITION SWITCH-II

−

Voltage

Stop lamp switch

Connector

Terminal

E102

E118

Ground

Battery voltage

−

Continuity

Stop lamp switch

ECM

Connector

Terminal

Connector

Terminal

E102

E118

E18

115

Existed

Brake pedal position switch

Condition

Continuity

−

Terminals

Brake pedal

Fully released

Existed

Slightly de-
pressed

Not existed

Revision: November 2015

2016 JUKE

Content .. 205 206 207 208 ..