Nissan Juke (2016 year). Service Repair Manual - part 200

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     198      199      200      201     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 200

 

 

P0603 ECM

EC-415

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P0603 ECM

DTC Logic

INFOID:0000000012197954

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition

switch ON.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON and wait at least 1 second.

2. Turn ignition switch OFF and wait at least 10 seconds.

3. Repeat step 1 and 2 for 10 times.

4. Turn ignition switch ON.

5. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-415, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197955

1.

CHECK ECM POWER SUPPLY AND GROUND CIRCUIT

Perform trouble diagnosis for ECM power supply and ground circuit. Refer to 

EC-187, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace error-detected parts.

2.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts.

3.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Erase DTC.

3. Perform DTC confirmation procedure. Refer to 

EC-415, "DTC Logic"

.

Is the 1st trip DTC P0603 displayed again?

YES

>> Replace ECM. Refer to 

EC-590, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P0603

ECM BACK UP CIRCUIT
[Internal control module keep 
alive memory (KAM) error]

• Malfunction in the internal back up RAM of ECM.
• Malfunction in the internal EEP-ROM system of 

ECM.

• ECM  power  supply
• ECM

Revision: November 2015

2016 JUKE

EC-416

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P0604 ECM

P0604 ECM

DTC Logic

INFOID:0000000012197956

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition

switch ON.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON (engine stopped) and wait least 20 minutes.

CAUTION:

Never start engine during this procedure.

2. Turn ignition switch OFF and wait at least 10 seconds.

3. Turn ignition switch ON.

4. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-416, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197957

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Erase DTC.

3. Perform DTC confirmation procedure. Refer to 

EC-416, "DTC Logic"

.

Is the 1st trip DTC P0604 displayed again?

YES

>> Replace ECM. Refer to 

EC-590, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P0604

ECM
[Internal control module 
random access memory 
(RAM) error]

Malfunction in the internal RAM of ECM.

ECM

Revision: November 2015

2016 JUKE

P0605 ECM

EC-417

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P0605 ECM

DTC Logic

INFOID:0000000012197958

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition

switch ON.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON (engine stopped) and wait least 20 minutes.

CAUTION:

Never start engine during this procedure.

2. Turn ignition switch OFF and wait at least 10 seconds.

3. Turn ignition switch ON.

4. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-417, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197959

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Erase DTC.

3. Perform DTC confirmation procedure. Refer to 

EC-417, "DTC Logic"

.

Is the 1st trip DTC P0605 displayed again?

YES

>> Replace ECM. Refer to 

EC-590, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P0605

ECM
[Internal control module 
read only memory (ROM) 
error]

Malfunction in the internal ROM of ECM.

ECM

Revision: November 2015

2016 JUKE

EC-418

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P0606 ECM

P0606 ECM

DTC Logic

INFOID:0000000012197960

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition

switch ON.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE-I

1. Turn ignition switch ON (engine stopped) and wait at least 10 seconds.

CAUTION:

Never start engine during this procedure.

2. Turn ignition switch OFF and wait at least 10 seconds.

3. Turn ignition switch ON.

4. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-418, "Diagnosis Procedure"

.

NO

>> GO TO 3.

3.

PERFORM DTC CONFIRMATION PROCEDURE-II

1. Start engine.

2. Rev up the engine quickly to approximately 3,000 rpm under unloaded condition and completely release

the accelerator pedal.

3. Let the engine idle and wait at least 10 seconds.

4. Turn ignition switch OFF and wait at least 10 seconds.

5. Turn ignition switch ON.

6. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-418, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197961

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Erase DTC.

3. Perform DTC confirmation procedure for 3 times. Refer to 

EC-418, "DTC Logic"

.

Is the 1st trip DTC P0606 displayed again?

YES

>> Replace ECM. Refer to 

EC-590, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P0606

CONTROL MODULE
(Control module processor)

Malfunction in ECM processor.

ECM

Revision: November 2015

2016 JUKE

P0607 ECM

EC-419

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P0607 ECM

DTC Logic

INFOID:0000000012197962

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition

switch ON.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON (engine stopped) and wait least 10 seconds.

2. Turn ignition switch OFF and wait at least 10 seconds.

3. Turn ignition switch ON.

4. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-419, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197963

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Erase DTC.

3. Perform DTC confirmation procedure. Refer to 

EC-419, "DTC Logic"

.

Is the 1st trip DTC P0607 displayed again?

YES

>> Replace ECM. Refer to 

EC-590, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P0607

ECM
(Control module perfor-
mance)

ECM internal communication system is malfunc-
tioning.

ECM

Revision: November 2015

2016 JUKE

EC-420

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P060A ECM

P060A ECM

DTC Logic

INFOID:0000000012197964

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition

switch ON.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start engine and wait at least 10 seconds.

2. Turn ignition switch OFF and wait at least 10 seconds.

3. Repeat step 1 and 2 for 5 times.

4. Turn ignition switch ON.

5. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-420, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197965

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Erase DTC.

3. Perform DTC confirmation procedure. Refer to 

EC-420, "DTC Logic"

.

Is the 1st trip DTC P060A displayed again?

YES

>> Replace ECM. Refer to 

EC-590, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P060A

CONTROL MODULE
(Internal control module 
monitoring processor per-
formance)

ECM internal monitoring processor is malfunction-
ing.

ECM

Revision: November 2015

2016 JUKE

P060B ECM

EC-421

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P060B ECM

DTC Logic

INFOID:0000000012197966

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition

switch ON.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON (engine stopped) and wait least 10 seconds.

2. Turn ignition switch OFF and wait at least 10 seconds.

3. Turn ignition switch ON.

4. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-421, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197967

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Erase DTC.

3. Perform DTC confirmation procedure. Refer to 

EC-421, "DTC Logic"

.

Is the 1st trip DTC P060B displayed again?

YES

>> Replace ECM. Refer to 

EC-590, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P060B

CONTROL MODULE
(Internal control module A/
D processing performance)

ECM internal analog/digital conversion processing 
system is malfunctioning.

ECM

Revision: November 2015

2016 JUKE

EC-422

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P0611 ECM PROTECTION

P0611 ECM PROTECTION

Description

INFOID:0000000012197968

This DTC is detected when the ECM protective function is activated due to an extreme temperature increase

in ECM, resulting from severe conditions such as heavy load driving.

DTC Logic

INFOID:0000000012197969

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

This DTC is displayed as protection function history. If no malfunction is detected after the diagnosis, the cus-

tomer must be informed of the activation of the protection function.

>> Proceed to 

EC-422, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012197970

1.

INSPECTION START

1. Perform DTC confirmation procedure. Refer to 

EC-417, "DTC Logic"

.

2. Check 1st trip DTC.
Is DTC P0605 detected?

YES

>> Proceed to 

EC-417, "Diagnosis Procedure"

.

NO

>> Explain the customer about the activation of the protection function.

DTC No.

Trouble diagnosis name

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P0611

FIC MODULE
(ECM protection)

ECM overheat protection control is activated.

ECM overheated

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     198      199      200      201     ..