Nissan Juke (2016 year). Service Repair Manual - part 175

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     173      174      175      176     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 175

 

 

P0078 EVT CONTROL SOLENOID VALVE

EC-215

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

4. Also check harness for short to ground.
Is the inspection result normal?

YES

>> Perform the trouble diagnosis for power supply circuit.

NO

>> Repair or replace error-detected parts.

3.

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between EVT control solenoid valve harness connector and ECM harness connec-

tor.

4. Also check harness for short to ground and to power. 
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace error-detected parts.

4.

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE

Check the exhaust valve timing control solenoid valve. Refer to 

EC-212, "Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Replace exhaust valve timing control solenoid valve.

Component Inspection

INFOID:0000000012197772

1.

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE-I

1. Turn ignition switch OFF.

2. Disconnect exhaust valve timing control solenoid valve harness connector.

3. Check resistance between exhaust valve timing control solenoid valve terminals as per the following.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace exhaust valve timing control solenoid valve. Refer to 

EM-76, "Exploded View"

.

2.

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE-II

1. Remove exhaust valve timing control solenoid valve. Refer to 

EM-76, "Exploded View"

.

+

+

Continuity

EVT control solenoid valve

IPDM E/R

Connector

Terminal

Connector

Terminal

F100

2

E14

36

Existed

+

+

Continuity

EVT control solenoid valve

ECM

Connector

Terminal

Connector

Terminal

F100

1

F26

85

Existed

Exhaust valve timing control solenoid valve

Resistance

+

Terminal

1

 2

7.0 - 7.7 

 [at 20

°

C (68

°

F)]

1

Ground

 

(Continuity should not exist)

2

Revision: November 2015

2016 JUKE

EC-216

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P0078 EVT CONTROL SOLENOID VALVE

2. Provide 12 V DC between exhaust valve timing control solenoid

valve terminals 1 and 2, and then interrupt it. Check that the

plunger moves as shown in the figure.

CAUTION:

Do not apply 12 V DC continuously for 5 seconds or more.

Doing so may result in damage to the coil in exhaust valve

timing control solenoid valve.

NOTE:

Always replace O-ring when exhaust valve timing control

solenoid valve is removed.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace exhaust valve timing control solenoid valve. Refer to 

EM-76, "Exploded View"

.

JMBIA0079ZZ

Revision: November 2015

2016 JUKE

P0087 FRP CONTROL SYSTEM

EC-217

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P0087 FRP CONTROL SYSTEM

DTC Logic

INFOID:0000000012197773

DTC DETECTION LOGIC

NOTE:

If DTC P0087 is displayed with DTC P0090 and/or P1197, first perform the trouble diagnosis for DTC

P0090 and/or P1197.

• DTC P0087 may be displayed when running out of gas or air accumulation.

DTC CONFIRMATION PROCEDURE

1.

CHECK FUEL LEAKAGE

1. Turn ignition switch ON.

2. Visually check the piping between low pressure fuel pump and fuel injectors for fuel leakage.

3. Start the engine.

4. Visually check the piping between low pressure fuel pump and fuel injectors for fuel leakage.
Is inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace error-detected parts.

2.

PRECONDITIONING

If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following proce-

dure before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

Before performing the following procedure, check that the fuel tank is 1/8 full of fuel.

>> GO TO 3.

3.

PERFORM DTC CONFIRMATION PROCEDURE-1

WITH CONSULT

1. Turn ignition switch ON.

2. Select “COOLAN TEMP/S” in “DATA MONITOR” mode of “ENGNE” using CONSULT.

3. Check the following condition;.

DTC No.

Trouble diagnosis name

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P0087

LOW FUEL PRES
(High fuel pressure too low)

• Fuel rail pressure does not reach 1.3 

MPa (13 bar, 13.3 kg/cm2, 188.5 psi) 
at engine cold start [water tempera-
ture 5

°

C (41

°

F) – 40

°

C (104

°

F)].

• Fuel rail pressure remains at 8.5 MPa 

(85 bar, 86.7 kg/cm2, 1232.8 psi) or 
less for 1 second or more during en-
gine idle condition after cold start [wa-
ter temperature 5

°

C (41

°

F) – 40

°

C  

(104

°

F)].

• The following condition continues for 

5 seconds or more after engine start 
(regardless of water temperature): 
Target fuel pressure – Actual fuel 
pressure 

 2.7 MPa (27 bar, 27.5 kg/

cm2, 392 psi).

• Fuel system
• Leakage in fuel line
• High pressure fuel pump
• Low pressure fuel pump
• Damage in lifter

COOLAN TEMP/S

: 5 – 40

°

C (41 – 104

°

F)

Revision: November 2015

2016 JUKE

EC-218

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P0087 FRP CONTROL SYSTEM

WITH GST

Follow the above steps for “WITH CONSULT”.
Is the condition satisfied?

YES

>> GO TO 4.

NO

>> 1. Satisfy the condition.

2. Retry from step 1.

4.

PERFORM DTC CONFIRMATION PROCEDURE-2

WITH CONSULT

1. Start the engine and let it idle for 10 seconds.

2. Check 1st trip DTC.

WITH GST

Follow the above steps for “WITH CONSULT”.
Is 1st trip DTC detected?

YES

>> Proceed to  

EC-218, "Diagnosis Procedure"

.

NO

>> GO TO 5.

5.

PERFORM DTC CONFIRMATION PROCEDURE-3

WITH CONSULT

1. Select “COOLAN TEMP/S” in “DATA MONITOR” mode of “ENGINE” using CONSULT.

2. Maintain the following condition for 10 seconds or more at idle.

3. Check 1st trip DTC.

WITH GST

Follow the above steps for “WITH CONSULT”.
Is 1st trip DTC detected?

YES

>> Proceed to  

EC-218, "Diagnosis Procedure"

.

NO

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000012197774

1.

PERFORM THE HIGH PRESSURE FUEL PUMP COMPONENT INSPECTION

Perform the high pressure fuel pump component inspection. Refer to 

EC-218, "Component Inspection (High

Pressure Fuel Pump)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace high pressure fuel pump. 

EM-49, "Removal and Installation"

.

2.

CHECK FUEL LEAKAGE

1. Start the engine.

2. Visually check that the fuel pump, fuel rail, and fuel piping have no fuel leakage.
Is the inspection result normal?

YES

>> Check that the fuel system has no breakage, bend, and crush. Refer to 

FL-5, "Inspection"

.

NO

>> Repair or Replace the error-detected parts.

Component Inspection (High Pressure Fuel Pump)

INFOID:0000000012197775

1.

CHECK HIGH PRESSURE FUEL PUMP-1

1. Turn ignition switch OFF.

2. Disconnect high pressure fuel pump harness connector.

3. Check the resistance between high pressure fuel pump terminals.

COOLAN TEMP/S

: 70

°

C (104

°

F) or more

Revision: November 2015

2016 JUKE

P0087 FRP CONTROL SYSTEM

EC-219

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace high pressure fuel pump. Refer to 

EM-49, "Removal and Installation"

.

2.

CHECK HIGH PRESSURE FUEL PUMP-2

WITH CONSULT

1. Reconnect high pressure fuel pump harness connector.

2. Start the engine.

3. Check “FUEL PRES SEN V” in “DATA MONITOR” mode of “ECM” using CONSULT.

WITHOUT CONSULT

1. Reconnect high pressure fuel pump harness connector.

2. Start the engine.

3. Check FRP sensor signal voltage.

YES

>> INSPECTION END

NO

>> Replace high pressure fuel pump. Refer to 

EM-49, "Removal and Installation"

.

+

Condition

Resistance

(Approx.)

High pressure fuel pump

Terminal

1

2

Temperature 

°

C (

°

F)

20 – 30 (68 - 86)

0.46 - 0.56 

Monitor item

Condition

Voltage

(Approx.)

FUEL PRES SEN V

Engine speed: idle

1,140 – 1,460 mV

Engine speed: Revving engine from idle to 4,000 rpm quickly

1,140 – 3,060 mV

ECM

Condition

Value

(Approx.)

Connector

+

Terminal

F25

18

44

Engine speed: idle

1,140 – 1,460 mV

Engine speed: Revving engine from idle to 4,000 rpm quickly

1,140 – 3,060 mV

Revision: November 2015

2016 JUKE

EC-220

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P0088 FRP CONTROL SYSTEM

P0088 FRP CONTROL SYSTEM

DTC Logic

INFOID:0000000012197776

DTC DETECTION LOGIC

NOTE:

If DTC P0088 is displayed with DTC P0090, first perform the trouble diagnosis for DTC P0090.

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following proce-

dure before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

Before performing the following procedure, check that the fuel tank is 1/8 full of fuel.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE-1

1. Warm up the engine to the normal operating temperature and keep the engine speed at idle for 10 sec-

onds.

NOTE:

Warm up the engine until “COOLANT TEMP/S” on “DATA MONITOR” mode of “ENGINE” using CON-

SULTIII reaches at least 70

°

C (158

°

F).

2. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to  

EC-222, "Diagnosis Procedure"

.

NO

>> GO TO 3.

3.

PERFORM DTC CONFIRMATION PROCEDURE-2

1. Cool the engine until the engine coolant temperature reaches 60

°

C (140

°

F) or less.

2. Start the engine and wait at least 40 seconds.

3. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to  

EC-222, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197777

1.

PERFORM THE HIGH PRESSURE FUEL PUMP COMPONENT INSPECTION

DTC No.

Trouble diagnosis name

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P0088

HIGH FUEL PRES
(High fuel pressure too high)

• Fuel rail pressure remains at more 

than 12.5 MPa (125 bar, 127.5 kg/
cm2, 1812.5 psi) for 1 second or more 
during engine idle condition after cold 
start [water temperature 5

°

C (41

°

F) - 

40

°

C (104

°

F)].

• The following condition continues for 

5 seconds or more after engine start 
(regardless of water temperature): 
Actual fuel pressure 

 Target fuel 

pressure 

 2.7 MPa (27 bar, 27.5 kg/

cm

2

, 392 psi)

• Harness or connector

(The high pressure fuel pump circuit is 
open or shorted)

• High pressure fuel pump

Revision: November 2015

2016 JUKE

P0088 FRP CONTROL SYSTEM

EC-221

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Perform the high pressure fuel pump component inspection. Refer to 

EC-221, "Component Inspection (High

Pressure Fuel Pump)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace high pressure fuel pump. 

EM-49, "Removal and Installation"

.

2.

CHECK FUEL LEAKAGE

1. Start the engine.

2. Visually check that the fuel pump, fuel rail, and fuel piping have no fuel leakage.
Is the inspection result normal?

YES

>> Check that the fuel system has no breakage, bend, and crush. Refer to 

FL-5, "Inspection"

.

NO

>> Repair or Replace the error-detected parts.

Component Inspection (High Pressure Fuel Pump)

INFOID:0000000012197778

1.

CHECK HIGH PRESSURE FUEL PUMP-1

1. Turn ignition switch OFF.

2. Disconnect high pressure fuel pump harness connector.

3. Check the resistance between high pressure fuel pump terminals.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace high pressure fuel pump. Refer to 

EM-49, "Removal and Installation"

.

2.

CHECK HIGH PRESSURE FUEL PUMP-2

WITH CONSULT

1. Reconnect high pressure fuel pump harness connector.

2. Start the engine.

3. Check “FUEL PRES SEN V” in “DATA MONITOR” mode of “ECM” using CONSULT.

WITHOUT CONSULT

1. Reconnect high pressure fuel pump harness connector.

2. Start the engine.

3. Check FRP sensor signal voltage.

YES

>> INSPECTION END

NO

>> Replace high pressure fuel pump. Refer to 

EM-49, "Removal and Installation"

.

+

Condition

Resistance

(Approx.)

High pressure fuel pump

Terminal

1

2

Temperature 

°

C (

°

F)

20 – 30 (68 - 86)

0.46 - 0.56 

Monitor item

Condition

Voltage

(Approx.)

FUEL PRES SEN V

Engine speed: idle

1,140 – 1,460 mV

Engine speed: Revving engine from idle to 4,000 rpm quickly

1,140 – 3,060 mV

ECM

Condition

Value

(Approx.)

Connector

+

Terminal

F25

18

44

Engine speed: idle

1,140 – 1,460 mV

Engine speed: Revving engine from idle to 4,000 rpm quickly

1,140 – 3,060 mV

Revision: November 2015

2016 JUKE

EC-222

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P0090 HIGH PRESSURE FUEL PUMP

P0090 HIGH PRESSURE FUEL PUMP

DTC Logic

INFOID:0000000012197779

DTC DETECTION LOGIC

NOTE:

• If DTC P0090 is displayed with DTC P1197, first perform the trouble diagnosis for DTC P1197.

• DTC P0090 may be displayed when running out of gas.

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following proce-

dure before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

Before performing the following procedure, check that the fuel tank is 1/8 full of fuel.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE-I

WITH CONSULT

1. Start engine.

2. Select “COOLAN TEMP/S” in “DATA MONITOR” mode of “ENGNE” using CONSULT.

3. Maintain the following condition for 5 seconds or more at idle.

4. Check 1st trip DTC.

WITH GST

Follow the above steps for “WITH CONSULT”.
Is 1st trip DTC detected?

YES

>> Proceed to  

EC-222, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197780

1.

CHECK HIGH PRESSURE FUEL PUMP POWER SUPPLY

1. Turn ignition switch ON.

2. Check the voltage between ECM harness connector and ground.

DTC No.

Trouble diagnosis name

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P0090

FUEL PUMP
(High pressure fuel pump cir-
cuit)

• Fuel rail pressure remains at 1.1 MPa 

(11 bar, 11.2 kg/ cm

2

, 159.5 psi) or 

less for 5 seconds or more during en-
gine rev.

• Fuel rail pressure remains at 18.5 

MPa (185 bar, 188.7 kg/ cm

2

, 2682.5 

psi) or more for 0.3 seconds or more 
during engine rev.

• Harness or connectors

(The fuel pump circuit is open or shorted.)

• High pressure fuel pump

COOLAN TEMP/S

: 70

°

C (104

°

F) or more

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     173      174      175      176     ..