Content .. 133 134 135 136 ..

Nissan Juke (2016 year). Service Repair Manual - part 135

AWD WARNING LAMP BLINKS SLOWLY

DLN-87

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY21B]

DLN

AWD WARNING LAMP BLINKS SLOWLY

Description

INFOID:0000000012199451

AWD warning lamp blinks at approximately 2 seconds intervals while driving.

Diagnosis Procedure

INFOID:0000000012199452

CHECK VEHICLE SPEED SIGNAL

With CONSULT

1. Turn the ignition switch ON.

2. Check that each value of “WHEEL SPD SEN FR”, “WHEEL SPD SEN FL”, “WHEEL SPD SEN RR”, and

“WHEEL SPD SEN RL” in “DATA MONITOR” for “ALL MODE AWD/4WD” is almost equal.

Is the inspection result normal?

YES

>> GO TO 2.

>> Proceed to

DLN-44, "Diagnosis Procedure"

CHECK TIRE

Check the following.

• Tire pressure

• Tire wear condition

• Front and rear tire size (There is no difference between front and rear tires.)
Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace error-detected parts.

TERMINAL INSPECTION

Check AWD control module harness connector for disconnection.
Is the inspection result normal?

YES

>> Replace AWD control module. Refer to

DLN-91, "Removal and Installation"

>> Repair or replace the error-detected parts.

Revision: November 2015

2016 JUKE

DLN-88

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY21B]

DECREASE IN TURNING PERFORMANCE

DECREASE IN TURNING PERFORMANCE

Description

INFOID:0000000012199453

Turning performance decreases when driving in AWD-V mode or AWD mode.

Diagnosis Procedure

INFOID:0000000012199454

PERFORM EPS CONTROL UNIT SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “EPS”.
Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to

STC-13, "DTC Index"

>> GO TO 2.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to

DLN-31, "DTC Index"

>> GO TO 3.

CHECK AWD SOLENOID

Perform the trouble diagnosis of the AWD solenoid. Refer to

DLN-57, "Diagnosis Procedure"

(Lef t side),

DLN-

60, "Diagnosis Procedure"

(Right side).

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the error-detected parts.

CHECK ELECTRIC CONTROLLED COUPLING

1. Turn the ignition switch OFF.

2. Set the transaxle to neutral. Release the parking brake.

3. Lift up the vehicle.

4. Rotate the propeller shaft.

5. Hold the rear wheel of right and left lightly.
Does the rear wheel rotate?

YES

>> Replace electric controlled coupling for mechanical malfunction (clutch sticking etc.). Refer to

DLN-145, "Removal and Installation"

>> Check each harness connector pin terminal for disconnection.

Revision: November 2015

2016 JUKE

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

DLN-89

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY21B]

DLN

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

NVH Troubleshooting Chart

INFOID:0000000012199455

Use the chart below to find the cause of the symptom. The numbers indicate the order of the inspection. If necessary, repair or replace these

parts.

Reference

SUSPECTED PARTS
(Possible cause)

ANSFER OIL (Level

low

)

ANSFER OIL (W

rong)

ANSFER OIL (Level

too high)

QUI

GASKET (Dam

)

OIL

SEAL

orn

or da

GEAR

orn

EARING

orn

Symptom

Noise

Transfer oil leakage

Revision: November 2015

2016 JUKE

DLN-90

< PERIODIC MAINTENANCE >

[TRANSFER: TY21B]

TRANSFER OIL

PERIODIC MAINTENANCE

TRANSFER OIL

Inspection

INFOID:0000000012199456

OIL LEAKAGE

Check transfer surrounding area (oil seal, drain plug, filler plug, and transfer case etc.) for oil leakage.

OIL LEVEL

1. Remove filler plug (1) and gasket. Then check that oil is filled up

from mounting hole for the filler plug.

CAUTION:

Never start engine while checking oil level.

2. Before installing filler plug, set a new gasket. Install filler plug on

transfer and tighten to the specified torque. Refer to

DLN-116,

"Exploded View"

CAUTION:

Never reuse gasket.

Draining

INFOID:0000000012199457

1. Run the vehicle to warm up the transfer unit sufficiently.
2. Stop the engine and remove the drain plug (1) and gasket to

drain the transfer oil.

3. Before installing drain plug, set a new gasket. Install drain plug

on the transfer and tighten to the specified torque. Refer to

DLN-

116, "Exploded View"

CAUTION:

Never reuse gasket.

Refilling

INFOID:0000000012199458

1. Remove filler plug (1) and gasket. Then fill oil up to mounting

hole for the filler plug.

CAUTION:

Carefully fill the oil. (Fill up for approximately 3 minutes.)

2. Leave the vehicle for 3 minutes, and check the oil level again.
3. Before installing filler plug, set a new gasket. Install filler plug on transfer and tighten to the specified

torque. Refer to

DLN-116, "Exploded View"

CAUTION:

Never reuse gasket.

: Vehicle front

JSDIA2080ZZ

: Vehicle front

JSDIA2081ZZ

: Vehicle front

Oil and viscosity

: Refer to

MA-11, "Fluids

and Lubricants"

Oil capacity

: Refer to

DLN-120, "Gen-

eral Specifications"

JSDIA2080ZZ

Revision: November 2015

2016 JUKE

AWD CONTROL MODULE

DLN-91

< REMOVAL AND INSTALLATION >

[TRANSFER: TY21B]

DLN

REMOVAL AND INSTALLATION

AWD CONTROL MODULE

Exploded View

INFOID:0000000012199459

Removal and Installation

INFOID:0000000012199460

REMOVAL

1. Turn the ignition switch OFF.
2. Remove front seat (left side). Refer to

SE-21, "Removal and Installation"

3. Remove dush side finisher (left side). Refer to

INT-21, "DASH SIDE FINISHER : Removal and Installa-

tion"

4. Remove front and rear kicking plate inner. Refer to

INT-19, "KICKING PLATE INNER : Removal and

Installation"

5. Remove rear seat cushion. Refer to

SE-32, "SEAT CUSHION : Removal and Installation"

6. Remove outer anchor of front seat belt (passenger side). Refer to

SB-5, "Exploded View"

7. Remove harness clip.
8. Turn floor carpet. Refer to

INT-24, "Removal and Installation"

9. Disconnect AWD control module harness connector.
10. Remove AWD control module mounting nuts.
11. Remove AWD control module.

INSTALLATION

Note the following, and install in the reverse order of removal.

• When installing AWD control module, install it following procedure.

AWD control module

AWD control module harness con-
nector

: Vehicle front

: N·m (kg-m, in-lb)

JSDIA2374GB

Revision: November 2015

2016 JUKE

DLN-92

< REMOVAL AND INSTALLATION >

[TRANSFER: TY21B]

AWD CONTROL MODULE

1. Align the securing holes (A) of bracket as shown in the figure

and temporarily tighten mounting bolts.

2. When replace AWD control module, hold AWD control module

and remove protector paper on the adhesion area of bracket to

bond to the front floor (LH).

3. Tighten mounting bolts to the specified torque.
• When replacing AWD control module, perform writing unit parame-

ter. Refer to

DLN-42, "Work Procedure"

: Vehicle front

JSDIA2375ZZ

Revision: November 2015

2016 JUKE

AWD MODE SWITCH

DLN-93

< REMOVAL AND INSTALLATION >

[TRANSFER: TY21B]

DLN

AWD MODE SWITCH

Removal and Installation

INFOID:0000000012199461

REMOVAL

1. Remove instrument lower panel. Refer to

IP-12, "Exploded View"

2. Remove AWD mode switch.

INSTALLATION

Install in the reverse order of removal.

Revision: November 2015

2016 JUKE

DLN-94

< UNIT REMOVAL AND INSTALLATION >

[TRANSFER: TY21B]

TRANSFER ASSEMBLY

UNIT REMOVAL AND INSTALLATION

TRANSFER ASSEMBLY

Exploded View

INFOID:0000000012199462

Removal and Installation

INFOID:0000000012199463

REMOVAL

1. Separate the propeller shaft from transfer. Then suspend it by wire, etc. Refer to

DLN-124, "Removal and

Installation"

CAUTION:

Constant velocity joint must be handled with care.

2. Remove right side drive shaft. Refer to

FAX-97, "AWD : Removal and Installation"

(Except for NISMO

RS),

FAX-45, "AWD : Removal and Installation"

(For NISMO RS).

3. Remove catalytic converter bracket (Except for NISMO RS) or catalyst convertor support bracket (upper)

(For NISMO RS). Refer to

EM-235, "AWD : Exploded View"

(Except for NISMO RS),

EM-37, "AWD :

Exploded View"

(For NISMO RS).

4. Remove heat insulator (1).

Transfer assembly

Transfer gusset

Heat insulator

: Vehicle front

: N·m (kg-m, ft-lb)

JSDIA2083GB

JSDIA2311ZZ

Revision: November 2015

2016 JUKE

Content .. 133 134 135 136 ..