Nissan Juke (2016 year). Service Repair Manual - part 131

DLN-56, "Diagnosis Procedure"

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P1820

ENGINE SPEED SIG

Malfunction is detected in engine speed
signal that is output from ECM through
CAN communication.

• ECM
• AWD control module
• CAN communication line

Revision: November 2015

2016 JUKE

DLN-56

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P1829 ACCELERATOR PEDAL POSITION SENSOR

P1829 ACCELERATOR PEDAL POSITION SENSOR

DTC Logic

INFOID:0000000012199399

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.

2. Stop the vehicle.

3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1829” detected?

YES

>> Proceed to

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199400

PERFORM ECM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ENGINE”.
Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to

EC-706, "DTC Index"

(Except for NISMO

RS),

EC-115, "DTC Index"

(For NISMO RS).

>> GO TO 2.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?

YES

>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1829”

is detected, Replace AWD control module. Refer to

DLN-57, "Diagnosis Procedure"

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P1829

THROTTLE POSI SEN

Malfunction is detected in accelerator
pedal position signal that is output from
ECM through CAN communication.

• ECM
• AWD control module
• CAN communication line

Revision: November 2015

2016 JUKE

P182D AWD SOLENOID (LEFT)

DLN-57

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

DLN

P182D AWD SOLENOID (LEFT)

DTC Logic

INFOID:0000000012199401

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

PERFORM DTC CONFIRMATION (1)

With CONSULT

1. Turn the ignition switch OFF to ON, and then wait for 5 seconds or more.

2. Turn the ignition switch OFF.

3. Turn the ignition switch ON, and then wait for 5 seconds or more.

4. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182D” detected?

YES

>> Proceed to

>> GO TO 3.

PERFORM DTC CONFIRMATION (2)

With CONSULT

1. Lift up the vehicle.

2. Start the engine, and run at idle for 1 second.

3. Stop the engine.

4. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182D” detected?

YES

>> Proceed to

DLN-57, "Diagnosis Procedure"

>> GO TO 4.

PERFORM DTC CONFIRMATION (3)

With CONSULT

1. Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute.

2. Stop the vehicle.

3. Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute again.

4. Stop the vehicle.

5. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182D” detected?

YES

>> Proceed to

DLN-57, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199402

CHECK AWD SOLENOID CIRCUIT (1)

1. Turn the ignition switch OFF.

2. Disconnect AWD control module harness connector.

3. Check the resistance between AWD control module harness connector.

DTC

Display item

Malfunction detected condition

Possible cause

P182D

SOLENOID LEFT

Malfunction related to AWD solenoid
(left) has been detected.

• Internal malfunction of electric con-

trolled coupling (left)

• Malfunction of AWD solenoid (left)

power supply circuit (open or short)

• Malfunction of AWD control module

Revision: November 2015

2016 JUKE

DLN-58

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P182D AWD SOLENOID (LEFT)

Is the inspection result normal?

YES

>> GO TO 5.

>> GO TO 2.

CHECK AWD SOLENOID CIRCUIT (2)

1. Disconnect rear final drive sub-harness connector.

2. Check the continuity between AWD control module harness connector and rear final drive sub-harness

connector.

3. Check the continuity between AWD control module harness connector and the ground.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the error-detected parts.

CHECK REAR FINAL DRIVE SUB-HARNESS

1. Disconnect electric controlled coupling (left) harness connector.

2. Check the continuity between rear final drive sub-harness connector and electric controlled coupling (left)

harness connector.

Is the inspection result normal?

YES

>> GO TO 4.

>> Replace rear final drive sub-harness. Refer to

DLN-145, "Exploded View"

CHECK AWD SOLENOID

Check AWD solenoid. Refer to

DLN-59, "Component Inspection"

Is the inspection result normal?

YES

>> GO TO 5.

>> AWD solenoid (left) is malfunctioning. Replace electric controlled coupling (left). Refer to

CHECK TERMINALS AND HARNESS CONNECTORS

1. Check AWD control module pin terminals for damage or loose connection with harness connector.

2. Check rear final drive sub-harness pin terminals for damage or loose connection with harness connector.

AWD control module

Condition

Resistance (Approx.)

Connector

Terminal

B47

C (50

2.55

Ω

C (68

2.65

Ω

C (86

2.76

Ω

AWD control module

Rear final drive sub-harness

Continuity

Connector

Terminal

Connector

Terminal

B47

B64

Existed

AWD control module

—

Continuity

Connector

Terminal

B47

Ground

Not existed

Rear final drive sub-harness

Electric controlled coupling (left)

Continuity

Connector

Terminal

Connector

Terminal

B84

B85

Existed

Revision: November 2015

2016 JUKE

P182D AWD SOLENOID (LEFT)

DLN-59

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

DLN

3. Check electric controlled coupling (left) pin terminals for damage or loose connection with harness con-

nector.

Is the inspection result normal?

YES

>> Replace AWD control module. Refer to

>> Repair or replace the error-detected parts.

Component Inspection

INFOID:0000000012199403

CHECK AWD SOLENOID

1. Turn the ignition switch OFF.

2. Disconnect electric controlled coupling (left) harness connector.

3. Check the resistance between electric controlled coupling (left) connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

>> AWD solenoid (left) is malfunctioning. Replace electric controlled coupling (left). Refer to

DLN-60, "Diagnosis Procedure"

Electric controlled coupling (left)

Condition

Resistance (Approx.)

Terminal

C (50

2.55

Ω

C (68

2.65

Ω

C (86

2.76

Ω

Revision: November 2015

2016 JUKE

DLN-60

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P182E AWD SOLENOID (RIGHT)

P182E AWD SOLENOID (RIGHT)

DTC Logic

INFOID:0000000012199404

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

PERFORM DTC CONFIRMATION (1)

With CONSULT

1. Turn the ignition switch OFF to ON, and then wait for 5 seconds or more.

2. Turn the ignition switch OFF.

3. Turn the ignition switch ON, and then wait for 5 seconds or more.

4. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182E” detected?

YES

>> Proceed to

>> GO TO 3.

PERFORM DTC CONFIRMATION (2)

With CONSULT

1. Lift up the vehicle.

2. Start the engine, and run at idle for 1 second.

3. Stop the engine.

4. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182E” detected?

YES

>> Proceed to

DLN-60, "Diagnosis Procedure"

>> GO TO 4.

PERFORM DTC CONFIRMATION (3)

With CONSULT

1. Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute.

2. Stop the vehicle.

3. Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute again.

4. Stop the vehicle.

5. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182E” detected?

YES

>> Proceed to

DLN-60, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199405

CHECK AWD SOLENOID CIRCUIT (1)

1. Turn the ignition switch OFF.

2. Disconnect AWD control module harness connector.

3. Check the resistance between AWD control module harness connector.

DTC

Display item

Malfunction detected condition

Possible cause

P182E

SOLENOID RIGHT

Malfunction related to AWD solenoid
(right) has been detected.

• Internal malfunction of electric con-

trolled coupling (right)

• Malfunction of AWD solenoid (right)

power supply circuit (open or short)

• Malfunction of AWD control module

Revision: November 2015

2016 JUKE

P182E AWD SOLENOID (RIGHT)

DLN-61

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

DLN

Is the inspection result normal?

YES

>> GO TO 5.

>> GO TO 2.

CHECK AWD SOLENOID CIRCUIT (2)

1. Disconnect rear final drive sub-harness connector.

2. Check the continuity between AWD control module harness connector and rear final drive sub-harness

connector.

3. Check the continuity between AWD control module harness connector and the ground.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the error-detected parts.

CHECK REAR FINAL DRIVE SUB-HARNESS

1. Disconnect electric controlled coupling (right) harness connector.

2. Check the continuity between rear final drive sub-harness connector and electric controlled coupling

(right) harness connector.

Is the inspection result normal?

YES

>> GO TO 4.

>> Replace rear final drive sub-harness. Refer to

DLN-145, "Exploded View"

CHECK AWD SOLENOID

Check AWD solenoid. Refer to

DLN-62, "Component Inspection"

Is the inspection result normal?

YES

>> GO TO 5.

>> AWD solenoid (right) is malfunctioning. Replace electric controlled coupling (right). Refer to

CHECK TERMINALS AND HARNESS CONNECTORS

1. Check AWD control module pin terminals for damage or loose connection with harness connector.

2. Check rear final drive sub-harness pin terminals for damage or loose connection with harness connector.

AWD control module

Condition

Resistance (Approx.)

Connector

Terminal

B47

C (50

2.55

Ω

C (68

2.65

Ω

C (86

2.76

Ω

AWD control module

Rear final drive sub-harness

Continuity

Connector

Terminal

Connector

Terminal

B47

B64

Existed

AWD control module

—

Continuity

Connector

Terminal

B47

Ground

Not existed

Rear final drive sub-harness

Electric controlled coupling (right)

Continuity

Connector

Terminal

Connector

Terminal

B84

B86

Existed

Revision: November 2015

2016 JUKE

DLN-62

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P182E AWD SOLENOID (RIGHT)

3. Check electric controlled coupling (right) pin terminals for damage or loose connection with harness con-

nector.

Is the inspection result normal?

YES

>> Replace AWD control module. Refer to

>> Repair or replace the error-detected parts.

Component Inspection

INFOID:0000000012199406

CHECK AWD SOLENOID

1. Turn the ignition switch OFF.

2. Disconnect electric controlled coupling (right) harness connector.

3. Check the resistance between electric controlled coupling (right) connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

>> AWD solenoid (right) is malfunctioning. Replace electric controlled coupling (right). Refer to