Nissan Juke (2016 year). Service Repair Manual - part 130

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     128      129      130      131     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 130

 

 

P1813 AWD MODE SWITCH

DLN-47

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

P1813 AWD MODE SWITCH

DTC Logic

INFOID:0000000012199386

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Turn the ignition switch OFF to ON.

2. Change AWD mode switch following order.

3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1813” detected?

YES

>> Proceed to 

DLN-47, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199387

1.

CHECK AWD MODE SWITCH

Check AWD mode switch. Refer to 

DLN-48, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace AWD mode switch. Refer to 

DLN-93, "Removal and Installation"

.

2.

CHECK AWD MODE SWITCH CIRCUIT (1)

1. Disconnect AWD control module harness connector.

2. Check the continuity between AWD control module harness connector and AWD mode switch harness

connector.

DTC

Display item

Malfunction detected condition

Possible cause

P1813

4WD MODE SW

Multiple signals received from AWD 
mode switch are detected.

• AWD mode switch
- Internal malfunction of AWD mode 

switch

- Malfunction of AWD mode switch cir-

cuit

• AWD control module

Changing order

: 2WD

AWD-V

AWD

AWD-V

2WD

Revision: November 2015

2016 JUKE

DLN-48

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P1813 AWD MODE SWITCH

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts.

3.

CHECK AWD MODE SWITCH CIRCUIT (2)

Check the continuity between AWD mode switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace error-detected parts.

4.

CHECK TERMINALS AND HARNESS CONNECTORS

• Check AWD control module pin terminals for damage or loose connection with harness connector.

• Check AWD mode switch pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?

YES

>> Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

Component Inspection

INFOID:0000000012199388

1.

CHECK AWD MODE SWITCH

1. Turn the ignition switch OFF.

2. Remove AWD mode switch. Refer to 

DLN-93, "Removal and Installation"

.

3. Check the continuity between AWD mode switch harness connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

AWD control module

AWD mode switch

Continuity

Connector

Terminal

Connector

Terminal

B47

9

M48

1

Existed

5

Not existed

6

Not existed

13

1

Not existed

5

Existed

6

Not existed

21

1

Not existed

5

Not existed

6

Existed

AWD mode switch

Continuity

Connector

Terminal

M48

3

Ground

Not existed

AWD switch assembly

Condition

Continuity

Terminal

1

3

AWD mode switch: 2WD

Not existed

AWD mode switch: AWD-V or AWD

Existed

5

3

AWD mode switch: 2WD

Existed

AWD mode switch: AWD-V or AWD

Not existed

6

3

AWD mode switch: 2WD or AWD-V

Not existed

AWD mode switch: AWD

Existed

Revision: November 2015

2016 JUKE

P1813 AWD MODE SWITCH

DLN-49

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

NO

>> Replace AWD mode switch. Refer to 

DLN-93, "Removal and Installation"

.

Revision: November 2015

2016 JUKE

DLN-50

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P181B INCOMPLETE SELFSHUT

P181B INCOMPLETE SELFSHUT

DTC Logic

INFOID:0000000012199389

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Turn the ignition switch OFF, and wait for several seconds.

2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181B” detected?

YES

>> Proceed to 

DLN-50, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199390

1.

CHECK AWD CONTROL MODULE POWER SUPPLY (1)

1. Turn the ignition switch OFF.

2. Disconnect AWD control module harness connector.

3. Check the voltage between AWD control module harness connector and ground.

4. Turn the ignition switch ON.

CAUTION:

Never start the engine.

5. Check the voltage between AWD control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK AWD CONTROL MODULE POWER SUPPLY (2)

1. Turn the ignition switch OFF.

2. Check the 10A fuse (Except for NISMO RS models: #23, For NISMO RS models: #33).

3. Check the harness for open or short between AWD control module harness connector No.1 terminal and

10A fuse (Except for NISMO RS models: #23, For NISMO RS models: #33).

Is the inspection result normal?

DTC

Display item

Malfunction detected condition

Possible cause

P181B

INCOMP SELF SHUT

When ignition switch is OFF and AWD 
control module power supply is lower or 
higher than normal

Self-shut of AWD control module is in-
complete.

AWD control module

Voltage

Connector

Terminal

B47

1

Ground

11 – 13 V

AWD control module

Voltage

Connector

Terminal

B47

1

Ground

11 – 13 V

Revision: November 2015

2016 JUKE

P181B INCOMPLETE SELFSHUT

DLN-51

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

YES

>> Perform the trouble diagnosis for power supply circuit. Refer to 

PG-12, "Wiring Diagram - BAT-

TERY POWER SUPPLY -"

.

NO

>> Repair or replace error-detected parts.

3.

CHECK AWD CONTROL MODULE GROUND

1. Turn the ignition switch OFF.

2. Check the continuity between AWD control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace error-detected parts.

4.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?

YES

>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P181B”

is detected, Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

AWD control module

Continuity

Connector

Terminal

B47

10

Ground

Existed

11

Revision: November 2015

2016 JUKE

DLN-52

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P181D ENGINE TORQUE SIGNAL

P181D ENGINE TORQUE SIGNAL

DTC Logic

INFOID:0000000012199391

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.

2. Stop the vehicle.

3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181D” detected?

YES

>> Proceed to 

DLN-52, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199392

1.

PERFORM ECM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ENGINE”.
Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

EC-706, "DTC Index"

 (Except for NISMO

RS), 

EC-115, "DTC Index"

 (For NISMO RS).

NO

>> GO TO 2.

2.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?

YES

>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P181D”

is detected, Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P181D

ENGINE SYSTEM

Malfunction is detected in engine torque 
signal that is output from ECM through 
CAN communication.

• ECM
• AWD  control  module
• CAN communication line

Revision: November 2015

2016 JUKE

P181E STEERING ANGLE SENSOR

DLN-53

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

P181E STEERING ANGLE SENSOR

DTC Logic

INFOID:0000000012199393

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Turn the ignition switch OFF to ON.

2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181E” detected?

YES

>> Proceed to 

DLN-53, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199394

1.

PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ABS”.
Is DTC “C1143” detected?

YES

>> Proceed to 

BRC-108, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?

YES

>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P181E”

is detected, Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P181E

STR ANGLE SEN

Malfunction is detected in steering angle 
sensor signal through CAN communica-
tion.

• Steering angle sensor
- Steering angle sensor error
- Malfunction of steering angle sensor 

circuit

• Malfunction of AWD control module
• CAN communication line

Revision: November 2015

2016 JUKE

DLN-54

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P181F INCOMPLETE CALIBRATION

P181F INCOMPLETE CALIBRATION

DTC Logic

INFOID:0000000012199395

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Turn the ignition switch OFF to ON.

2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181F” detected?

YES

>> Proceed to 

DLN-54, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199396

1.

PERFORM WRITING UNIT CHARACTERISTICS

1. Erase self-diagnostic result for “ALL MODE AWD/4WD”.

2. Perform writing unit characteristics. Refer to 

DLN-42, "Work Procedure"

.

3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC except “P181F” detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

DLN-31, "DTC Index"

.

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS AGAIN

With CONSULT

Perform “DTC CONFIRMATION PROCEDURE” (self-diagnosis) again. Refer to 

DLN-54, "DTC Logic"

.

Is DTC “P181F” detected?

YES

>> Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Check AWD control module pin terminals for damage or loose connection with harness connector.

If any items are damaged, repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P181F

INCOMP CALIBRATION

When incomplete writing unit character-
istics of rear final drive is detected.

Writing unit characteristics is incom-
plete.

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     128      129      130      131     ..