Nissan Juke (2016 year). Service Repair Manual - part 47

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     45      46      47      48     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 47

 

 

BR-38

< REMOVAL AND INSTALLATION >

BRAKE MASTER CYLINDER

BRAKE MASTER CYLINDER

Exploded View

INFOID:0000000012200287

Removal and Installation

INFOID:0000000012200288

REMOVAL 

CAUTION:

• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it

off immediately and wash with water if it gets on a painted surface. For brake component parts,

never wash them with water.

• Never depress the brake pedal while removing the brake tube. If this is not complied with, brake fluid

may splash.

1. Perform inspection before removal. Refer to 

BR-41, "Inspection"

.

2. Depress the brake pedal several times to release the vacuum pressure from the brake booster.
3. Drain brake fluid. Refer to 

BR-12, "Draining"

.

4. Disconnect the brake fluid level switch harness connector.
5. Remove air duct and air cleaner case. Refer to 

EM-27, "Removal and Installation"

.

1.

Reservoir cap

2.

Oil strainer

3.

Reservoir tank

4.

Master cylinder

5.

Pin

6.

O-ring

7.

Grommet

: Apply polyglycol ether based lubricant.

: Apply brake fluid.

: N·m (kg-m, ft-lb)

: Always replace after every disassembly.

JSFIA0476GB

Revision: November 2015

2016 JUKE

BRAKE MASTER CYLINDER

BR-39

< REMOVAL AND INSTALLATION >

C

D

E

G

H

I

J

K

L

M

A

B

BR

N

O

P

6. Separate the brake tube from master cylinder assembly with a

flare nut wrench (A).

CAUTION:

Never scratch the flare nut and the brake tube.

7. Remove the master cylinder assembly.

CAUTION:

• Never deform or bend the brake tubes.

• Never depress the brake pedal after the master cylinder

assembly is removed.

• The piston (A) of the master cylinder assembly is

exposed. Never damage it when removing the master cyl-

inder.

• The piston may drop off when pulled out strongly. Never

hold the piston. Hold the cylinder body when handling the

master cylinder assembly.

8. Remove the O-ring.

INSTALLATION

Note the following, and install in the reverse order of removal.

• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off

immediately and wash with water if it gets on a painted surface. For brake component parts, never wash

them with water.

• Never depress the brake pedal while removing the brake tube. If this is not complied with, brake fluid may

splash.

• Never depress the brake pedal after the master cylinder assembly is removed.

• Apply polyglycol ether based lubricant to the brake booster [see

(A) in the figure] when installing the master cylinder assembly to

the brake booster.

• The piston (A) of the master cylinder assembly is exposed. Never

damage it when handling the master cylinder.

• Check that no dirt and dust are present on the piston before instal-

lation. Clean it with new brake fluid if necessary.

• The piston may drop off when pulled strongly. Never hold the pis-

ton. Hold the cylinder body when handling the master cylinder

assembly.

• Never reuse the O-ring.

• Never deform or bend the brake tubes.

JPFIA0844ZZ

JPFIA0824ZZ

JPFIA0013ZZ

JPFIA0824ZZ

Revision: November 2015

2016 JUKE

BR-40

< REMOVAL AND INSTALLATION >

BRAKE MASTER CYLINDER

• Temporarily tighten the brake tube flare nut to the master cylinder

assembly by hand. Then tighten it to the specified torque with a

crowfoot and torque wrench (A). Refer to 

BR-23, "FRONT :

Exploded View"

.

• Perform the air bleeding. Refer to 

BR-13, "Bleeding Brake System"

• Perform inspection after installation. Refer to 

BR-41, "Inspection"

.

Disassembly and Assembly

INFOID:0000000012200289

DISASSEMBLY

CAUTION:

• Never disassemble the master cylinder.

• Remove the reservoir tank only when necessary.

1. Fix the master cylinder assembly to a vise.

CAUTION:

• Always set copper plates or cloth between vise grips when fixing the master cylinder to a vise.

• Never overtighten the vise.

2. Remove the reservoir tank mounting pin with a pin punch (A) [4

mm (0.157 in)].

3. Remove the reservoir tank and grommet from the master cylin-

der.

ASSEMBLY

CAUTION:

• Never use mineral oils such as kerosene or gasoline and rubber grease during the cleaning and

assembly process.

• Never allow foreign matter (e.g. dust) and oils other than brake fluid to enter the reservoir tank.

• Never drop the when installing. The parts must not be reused if they are dropped.

1. Apply new brake fluid to the grommet and install it to the master cylinder.

CAUTION:

Never reuse the grommets.

2. Install the reservoir tank to the master cylinder.
3. Fix the master cylinder to a vise.

CAUTION:

• Place the reservoir tank with the chamfered pin hole (

)

facing up.

• Always set copper plates or cloth between vise grips

when fixing the master cylinder to a vise.

• Never overtighten the vise.

JPFIA0844ZZ

JPFIA0825ZZ

JPFIA0826ZZ

Revision: November 2015

2016 JUKE

BRAKE MASTER CYLINDER

BR-41

< REMOVAL AND INSTALLATION >

C

D

E

G

H

I

J

K

L

M

A

B

BR

N

O

P

4. Tilt the reservoir tank so that a mounting pin can be inserted. Insert a mounting pin. Return the reservoir

tank to the horizontal position. Insert another mounting pin into the pin hole on the opposite side in the

same manner after the mounting pin passes through the master cylinder pin hole.

CAUTION:

Never reuse the mounting pin.

Inspection

INFOID:0000000012200290

INSPECTION BEFORE REMOVAL

Check the brake fluid level switch. Refer to 

BRC-116, "Component Inspection"

.

INSPECTION AFTER INSTALLATION

Check the following items and replace if necessary.

• Check the master cylinder for deformation, twist, contact with other parts or looseness of connection.

• Check for fluid leakage from connection. Refer to 

BR-27, "FRONT : Inspection"

.

CAUTION:

If the fluid leakage is present, retighten to the specified torque. Replace if necessary.

Revision: November 2015

2016 JUKE

BR-42

< REMOVAL AND INSTALLATION >

BRAKE BOOSTER

BRAKE BOOSTER

Exploded View

INFOID:0000000012200291

Removal and installation

INFOID:0000000012200292

REMOVAL

1. Perform inspection before removal. Refer to 

BR-43, "Inspection and Adjustment"

.

2. Remove cowl top and cowl top extension. Refer to 

EXT-30, "Removal and Installation"

.

3. Remove air duct and air cleaner case. Refer to 

EM-27, "Removal and Installation"

.

4. Remove brake master cylinder assembly. Refer to 

BR-38, "Removal and Installation"

.

5. Remove vacuum hose from brake booster. Refer to 

BR-46, "Removal and Installation"

.

6. Remove snap pin (1) and clevis pin (2). Refer to 

BR-20,

"Exploded View"

.

7. Remove nuts on brake booster and brake pedal assembly.

CAUTION:

Hold the brake booster so as to avoid dropping out.

8. Remove brake booster and spacer.

CAUTION:

Never deform or bend the brake tubes.

NOTE:

If removing brake booster is difficult, remove clevis from brake

booster.

9. Remove spacer from brake booster.
10. Perform inspection after removal. Refer to 

BR-43, "Inspection and Adjustment"

.

INSTALLATION

CAUTION:

Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it

off immediately and wash with water if it gets on a painted surface.

Note the following, and install in the reverse order of removal.

• Be careful not to damage brake booster stud bolt threads. If brake booster is tilted during installation, the

dash panel may damage the threads.

1.

Master cylinder assembly

2.

Brake booster

3.

Lock nut

4.

Clevis

5.

Gasket

6.

Spacer

: N·m (kg-m, ft-lb)

JSFIA0774GB

JPFIA0019ZZ

Revision: November 2015

2016 JUKE

BRAKE BOOSTER

BR-43

< REMOVAL AND INSTALLATION >

C

D

E

G

H

I

J

K

L

M

A

B

BR

N

O

P

• Never deform or bend the brake tubes when installing the brake booster.

• Always use a gasket between the brake booster and the spacer.

• Replace the clevis pin if it is damaged. Refer to 

BR-21, "Inspection and Adjustment"

.

• Perform the air bleeding. Refer to 

BR-13, "Bleeding Brake System"

.

• Check each item of brake pedal. Adjust it if the measurement value is not the standard. Refer to 

BR-9,

"Inspection and Adjustment"

.

Inspection and Adjustment

INFOID:0000000012200293

INSPECTION BEFORE REMOVAL

Air Tight

CAUTION:

Check the air tight condition when the master cylinder and the brake booster is installed.

1. Check the air tight use a handy vacuum pump.

2. If the air tight condition cannot be maintained, perform the following operation.
a. Check the no dirt and dust are present on the brake booster and brake master cylinder mating faces.

Clean it if necessary.

b. Check the O-ring on the master cylinder. If anything is found, replace the O-ring. Refer to 

BR-38,

"Removal and Installation"

.

c. Check the air tight condition again. If the condition still cannot be maintained, replace the brake booster.

INSPECTION AFTER REMOVAL

Input Rod Length Inspection

1. Loosen the lock nut (1) and adjust the input rod (2) to the speci-

fied length (A).

2. Tighten the lock nut to the specified torque.

INSPECTION AFTER INSTALLATION

Operation

Depress the brake pedal several times at 5-second intervals with the engine stopped. Start the engine with the

brake pedal fully depressed. Check that the clearance between brake pedal and dash lower panel decreases.

NOTE:

A slight impact with a small click may be felt on the pedal when the brake pedal is fully depressed. This is a

normal phenomenon due to the brake system operation.

Air Tight

1. Run the engine at idle for 1 minute to apply vacuum to the brake booster, and stop the engine.
2. Depress the brake pedal several times at 5-second intervals until the accumulated vacuum is released to

atmospheric pressure. Check that the clearance between brake pedal and dash lower panel gradually

increases each time the brake pedal is depressed when performing this operation.

3. Depress the brake pedal with the engine running. Then stop the engine while holding down the brake

pedal. Check that the brake pedal stroke does not change after holding down the brake pedal for 30 sec-

onds or more.

ADJUSTMENT AFTER INSTALLATION

At vacuum of 

66.7 kPa (

500 mmHg, 

19.69 inHg)

: Vacuum should decrease within 3.3 kPa (24.8 mmHg, 
0.98 inHg) for 15 seconds.

A

:  Refer  to 

BR-68, "Brake Booster"

.

JPFIA0238ZZ

Revision: November 2015

2016 JUKE

BR-44

< REMOVAL AND INSTALLATION >

BRAKE BOOSTER

Perform the brake pedal adjustment after installing the brake pedal assembly. Refer to 

BR-9, "Inspection and

Adjustment"

.

Revision: November 2015

2016 JUKE

VACUUM LINES

BR-45

< REMOVAL AND INSTALLATION >

C

D

E

G

H

I

J

K

L

M

A

B

BR

N

O

P

VACUUM LINES

Exploded View

INFOID:0000000012200294

EXCEPT NISMO RS

NISMO RS

1.

Vacuum piping A

2.

Clamp

3.

Vacuum hose A

4.

Vacuum piping B

5.

Vacuum hose (built-in check valve)

6.

Vacuum hose B

A.

Paint mark

B.

To engine side

C.

Stamp indicating engine direction

D.

To brake booster

: N·m (kg-m, in-lb)

JSFIA2856GB

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     45      46      47      48     ..