Nissan Juke (2016 year). Service Repair Manual - part 41

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     39      40      41      42     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 41

 

 

BCS

U0415 VEHICLE SPEED

BCS-85

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

U0415 VEHICLE SPEED

Description

INFOID:0000000012200735

U0415 is displayed if any unusual condition is present in the reception status of the vehicle speed signal from

the ABS actuator and electric unit (control unit).

DTC Logic

INFOID:0000000012200736

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC CONFIRMATION

1. Erase the DTC.

2. Turn ignition switch OFF.

3. Perform the “Self Diagnostic Result” of BCM with CONSULT, when passed 2 seconds or more after the

ignition switch is turned ON.

Is any DTC detected?

YES

>> Refer to 

BCS-85, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012200737

1.

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAG RESULTS 

Perform “Self-Diagnostic Result” of ABS actuator and electric unit (control unit) with CONSULT. Refer to 

BRC-

39, "CONSULT Function"

 (without EPS), 

BRC-39, "CONSULT Function"

 (with EPS).

Is any DTC detected?

YES

>> Repair or replace the malfunctioning part.

NO

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

DTC

 CONSULT display de-

scription

DTC Detection Condition

Probable cause

U0415

VEHICLE SPEED

When the vehicle speed signal received from 
the ABS actuator and electric unit (control 
unit) remains abnormal for 2 seconds or more.

• ABS actuator and electric unit (control unit)
• BCM

Revision: November 2015

2016 JUKE

BCS-86

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2562 LOW VOLTAGE

B2562 LOW VOLTAGE

DTC Logic

INFOID:0000000012200738

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC CONFIRMATION

1. Erase DTC.

2. Turn ignition switch OFF.

3. Perform the “Self Diagnostic Result” of BCM with CONSULT, when passed 120 seconds or more after the

ignition switch is turned ON.

Is any DTC detected?

YES

>> Refer to 

BCS-86, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012200739

1.

CHECK POWER SUPPLY CIRCUIT

Check BCM power supply circuit. Refer to 

BCS-87, "Diagnosis Procedure"

.

Is the circuit normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> Repair the malfunctioning part.

DTC

CONSULT display de-

scription

DTC Detection Condition

Possible cause

B2562

LOW VOLTAGE

When the power supply voltage to BCM remains less 
than 8.8 V for 120 seconds or more

Harness or connector (power supply 
circuit)

Revision: November 2015

2016 JUKE

BCS

POWER SUPPLY AND GROUND CIRCUIT

BCS-87

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

POWER SUPPLY AND GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000012200740

1.

CHECK FUSE AND FUSIBLE LINK

Check that the following fuse and fusible link are not blown (open).

Is the fuse or fusible link blown (open)?

YES

>> Replace the blown (open) fuse or fusible link after repairing the affected circuit if a fuse or fusible

link is blown (open).

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connectors.

3. Check voltage between BCM harness connector and ground.

Is the measurement value normal?

YES

>> GO TO 3.

NO

>> Repair harness or connector.

3.

CHECK GROUND CIRCUIT

Check continuity between BCM harness connector and ground.

Does continuity exist?

YES

>> INSPECTION END

NO

>> Repair harness or connector.

Signal name

Fuse and fusible link No.

Battery power supply

G (40 A)

9 (10 A)

Terminals

Voltage

(Approx.)

(+)

(

)

BCM

Ground

Connector

Terminal

M69

70

Battery voltage

57

BCM

Ground

Continuity

Connector

Terminal

M69

67

Existed

Revision: November 2015

2016 JUKE

BCS-88

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

COMBINATION SWITCH OUTPUT CIRCUIT

COMBINATION SWITCH OUTPUT CIRCUIT

Diagnosis Procedure

INFOID:0000000012200741

1.

CHECK OUTPUT 1 - 5 CIRCUIT FOR OPEN

1. Turn ignition switch OFF.

2. Disconnect BCM and combination switch connectors.

3. Check continuity between BCM harness connector and combination switch harness connector.

Does continuity exist?

YES

>> GO TO 2.

NO

>> Repair harnesses or connectors.

2.

CHECK OUTPUT 1 - 5 CIRCUIT FOR SHORT

Check for continuity between BCM harness connector and ground.

Does continuity exist?

YES

>> Repair harnesses or connectors.

NO

>> GO TO 3.

3.

CHECK BCM OUTPUT VOLTAGE

1. Connect BCM connector.

2. Check voltage between BCM harness connector and ground.

Is the measurement value normal?

System

BCM

Combination switch

Continuity

Connector

Terminal

Connector

Terminal

OUTPUT 1

M68

36

M27

11

Existed

OUTPUT 2

35

9

OUTPUT 3

34

7

OUTPUT 4

33

10

OUTPUT 5

32

13

System

BCM

Ground

Continuity

Connector

Terminal

OUTPUT 1

M68

36

Not existed

OUTPUT 2

35

OUTPUT 3

34

OUTPUT 4

33

OUTPUT 5

32

System

Terminals

Voltage

(Approx.)

(+)

(

)

BCM

Ground

Connector

Terminal

OUTPUT 1

M68

36

7.0 - 8.0 V

OUTPUT 2

35

OUTPUT 3

34

OUTPUT 4

33

OUTPUT 5

32

PKIB4960J

Revision: November 2015

2016 JUKE

BCS

COMBINATION SWITCH OUTPUT CIRCUIT

BCS-89

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

YES

>> Replace combination switch.

NO

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

Revision: November 2015

2016 JUKE

BCS-90

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

COMBINATION SWITCH INPUT CIRCUIT

COMBINATION SWITCH INPUT CIRCUIT

Diagnosis Procedure

INFOID:0000000012200742

1.

CHECK INPUT 1 - 5 CIRCUIT FOR OPEN

1. Turn ignition switch OFF.

2. Disconnect BCM and combination switch connectors.

3. Check continuity between BCM harness connector and combination switch harness connector.

Does continuity exist?

YES

>> GO TO 2.

NO

>> Repair harnesses or connectors.

2.

CHECK INPUT 1 - 5 CIRCUIT FOR SHORT

Check for continuity between BCM harness connector and ground.

Does continuity exist?

YES

>> Repair harnesses or connectors.

NO

>> GO TO 3.

3.

CHECK BCM INPUT SIGNAL

1. Connect BCM and combination switch connectors.

2. Turn ON any switch in the system that is malfunction.

3. Check voltage between BCM harness connector and ground.

Is the measurement value normal?

Yes

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

System

BCM

Combination switch

Continuity

Connector

Terminal

Connector

Terminal

INPUT 1

M68

6

M27

12

Existed

INPUT 2

5

14

INPUT 3

4

5

INPUT 4

3

2

INPUT 5

2

8

System

BCM

Ground

Continuity

Connector

Terminal

INPUT 1

M68

6

Not existed

INPUT 2

5

INPUT 3

4

INPUT 4

3

INPUT 5

2

System

Terminals

Voltage

(Approx.)

(+)

(

)

BCM

Ground

Connector

Terminal

INPUT 1

M68

6

Refer to 

BCS-

39, "Refer-

ence Value"

.

INPUT 2

5

INPUT 3

4

INPUT 4

3

INPUT 5

2

Revision: November 2015

2016 JUKE

BCS

COMBINATION SWITCH INPUT CIRCUIT

BCS-91

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

No

>> Replace combination switch.

Revision: November 2015

2016 JUKE

BCS-92

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

COMBINATION SWITCH SYSTEM SYMPTOMS

SYMPTOM DIAGNOSIS

COMBINATION SWITCH SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000012200743

1. Perform “Data Monitor” of CONSULT to check for any malfunctioning item.
2. Check the malfunction combinations.

Malfunction item: 

×

3. Identify the malfunctioning part from the agreed combination and repair or replace the part.

Data monitor item

Malfunc-

tion com-

bination

FR WI

PER HI

FR WIP

ER LOW

F

R

 W

A

SH

ER

 S

W

FR WI

PER INT

RR

 WIPE

R

 O

N

RR WIP

E

R INT

RR W

ASHER 

SW

INT VOL

U

ME

TURN SIG

NAL R

TURN SIGNAL L

TA

IL

 LA

MP 

SW

H

I BEAM SW

HEAD LAMP SW 

1

HEAD LAMP SW 

2

P

ASSI

N

G

 SW

AU

T

O

 LI

GH

T

 S

W

FR F

O

SW

×

×

×

×

A

×

×

×

×

B

×

×

×

×

C

×

×

×

×

D

×

×

×

E

×

×

×

F

×

×

×

×

G

×

×

×

H

×

×

×

×

I

×

×

×

×

J

All Items

K

If only one item is detected or the item is not applicable to the combinations A to K 

L

Malfunction 

combination

Malfunctioning part

Repair or replace

A

Combination switch OUTPUT 1 circuit

Inspect the combination switch output circuit applicable to the malfunction-
ing part. Refer to 

BCS-88, "Diagnosis Procedure"

.

B

Combination switch OUTPUT 2 circuit

C

Combination switch OUTPUT 3 circuit

D

Combination switch OUTPUT 4 circuit

E

Combination switch OUTPUT 5 circuit

F

Combination switch INPUT 1 circuit

Inspect the combination switch input circuit applicable to the malfunctioning 
part. Refer to 

BCS-90, "Diagnosis Procedure"

.

G

Combination switch INPUT 2 circuit

H

Combination switch INPUT 3 circuit

I

Combination switch INPUT 4 circuit

J

Combination switch INPUT 5 circuit

K

BCM

Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

L

Combination switch

Replace combination switch.

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     39      40      41      42     ..