Content .. 38 39 40 41 ..

Nissan Juke (2016 year). Service Repair Manual - part 40

BCS

BCM

BCS-77

< WIRING DIAGRAM >

[WITH INTELLIGENT KEY SYSTEM]

JRMWI5123GB

Revision: November 2015

2016 JUKE

BCS-78

< WIRING DIAGRAM >

[WITH INTELLIGENT KEY SYSTEM]

BCM

JRMWI5124GB

Revision: November 2015

2016 JUKE

BCS

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

BCS-79

< BASIC INSPECTION >

[WITH INTELLIGENT KEY SYSTEM]

BASIC INSPECTION

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

Description

INFOID:0000000012200723

Perform the following operations when replacing BCM. (For details, refer to

BCS-79, "Work Procedure"

BEFORE REPLACEMENT

When replacing BCM, save or print current vehicle specification with CONSULT configuration before replace-

ment.

NOTE:

If “Before Replace ECU” of “Read / Write Configuration” cannot be used, use the “Manual Configuration” after

replacing BCM.

AFTER REPLACEMENT

CAUTION:

When replacing BCM, always perform “Read / Write Configuration” or “Manual Configuration” with

CONSULT. Or not doing so, BCM control function does not operate normally.

• Complete the procedure of “Read / Write Configuration” in order.

• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.

• If you set incorrect “Read / Write Configuration” or “Manual Configuration”, incidents might occur.

NOTE:

When replacing BCM, perform the system initialization (NVIS) (if equipped).

Work Procedure

INFOID:0000000012200724

SAVING VEHICLE SPECIFICATION

CONSULT Configuration

Perform “Before Replace ECU” of “Read / Write Configuration” to save or print current vehicle specification.

Refer to

BCS-80, "Description"

NOTE:

If “Before Replace ECU” of “Read / Write Configuration” cannot be used, use the “Manual Configuration” after

replacing BCM.

>> GO TO 2.

REPLACE BCM

Replace BCM. Refer to

BCS-94, "Removal and Installation"

>> GO TO 3.

WRITING VEHICLE SPECIFICATION

CONSULT Configuration

Perform “After Replace ECU” of “Read / Write Configuration” or “Manual Configuration” to write vehicle speci-

fication. Refer to

BCS-80, "Work Procedure"

>> GO TO 4.

INITIALIZE BCM (NVIS) (IF EQUIPPED)

Perform BCM initialization. (NVIS)

>> WORK END

Revision: November 2015

2016 JUKE

BCS-80

< BASIC INSPECTION >

[WITH INTELLIGENT KEY SYSTEM]

CONFIGURATION (BCM)

CONFIGURATION (BCM)

Description

INFOID:0000000012200725

Vehicle specification needs to be written with CONSULT because it is not written after replacing BCM.

Configuration has three functions as follows. (For details, refer to

BCS-80, "Work Procedure"

NOTE:

Manual setting item: Items which need selection by vehicle specifications

Automatic setting item: Items which are written in automatically (Setting cannot be changed)

For some models and specifications, the automatic setting item may not be displayed.

CAUTION:

When replacing BCM, always perform “Re/programming, Configuration” with CONSULT. Or not doing

so, BCM control function does not operate normally.

• Complete the procedure of “Read / Write Configuration” in order.

• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.

• Never perform “Read / Write Configuration” except for new BCM.

• If you set incorrect “Read / Write Configuration”, incidents might occur.

Work Procedure

INFOID:0000000012200726

WRITING MODE SELECTION

CONSULT Configuration

Select “Re/programming, Configuration” of BCM.

When writing saved data>>GO TO 2.

When writing manually>>GO TO 3.

PERFORM “AFTER REPLACE ECU” OF “READ / WRITE CONFIGURATION”

CONSULT Configuration

Perform “After Replace ECU” of “Read / Write Configuration”.

>> WORK END

PERFORM “MANUAL CONFIGURATION”

CONSULT Configuration

1. Select “Manual Configuration”.

2. Identify the correct model and configuration list. Refer to

BCS-81, "Configuration list"

3. Confirm and/or change setting value for each item.

CAUTION:

Thoroughly read and understand the vehicle specification. ECU control may not operate normally

if the setting is not correct.

NOTE:

If items are not displayed, touch “Next”. Refer to

BCS-81, "Configuration list"

for written items and setting

value.

4. Touch “Next”.

5. Touch “OK”.

CAUTION:

Make sure to select “OK” even if the indicated configuration of brand new BCM is same as the

desirable configuration. If not, configuration which is set automatically by selecting vehicle model

cannot be memorized.

6. Check that the configuration has been successfully written and touch “End”.

Function

Description

Read / Write Configuration

Before Replace ECU

• Reads the vehicle configuration of current BCM.
• Saves the read vehicle configuration.

After Replace ECU

Writes the vehicle configuration with saved data.

Manual Configuration

Writes the vehicle configuration with manual selection.

Revision: November 2015

2016 JUKE

BCS

CONFIGURATION (BCM)

BCS-81

< BASIC INSPECTION >

[WITH INTELLIGENT KEY SYSTEM]

>> GO TO 4.

OPERATION CHECK

Confirm that each function controlled by BCM operates normally.

>> WORK END

Configuration list

INFOID:0000000012200727

CAUTION:

• Thoroughly read and understand the vehicle specification. ECU control may not operate normally if

the setting is not correct.

• The “setting value” of this vehicle is as follows: Never select any other value than the setting value

shown below. (If there is only 1 item in “setting value” that means that item is the only choice for this

certain vehicle.)

⇔

: Items which confirm vehicle specifications

SETTING ITEM

NOTE

Items

Setting value

AUTO LIGHT

WITH

⇔

WITHOUT

• WITH: With auto light system
• WITHOUT: Without auto light system

DTRL

WITHOUT

⇔

MODE1

⇔

MODE2

• WITHOUT: Without daytime running light system
• MODE1: With daytime running light system (For NISMO

models)

• MODE2: With daytime running light system (Except for NIS-

MO models)

TRANSMISSION

AT with ABS

⇔

MT with ABS

• AT with ABS: Except M/T models
• MT with ABS: M/T models

BCM AC CONTROL

MODE2

⇔

MODE4

• MODE2: Manual air conditioning system
• MODE4: Automatic air conditioning system

DONGLE

WITH

⇔

WITHOUT

• WITH: For Canada models
• WITHOUT: Except for Canada models

TIRE PRESSURE

230kPa

⇔

240kPa

⇔

250kPa

• 230kPa: 2WD M/T models
• 240kPa: AWD models
• 250kPa: 2WD except M/T models

Revision: November 2015

2016 JUKE

BCS-82

< BASIC INSPECTION >

[WITH INTELLIGENT KEY SYSTEM]

SHIPPING MODE CANCEL OPERATION

SHIPPING MODE CANCEL OPERATION

Description

INFOID:0000000012200728

SYSTEM DIAGRAM

DESCRIPTION

• The combination meter transmits meter CAN signal*

to BCM via CAN communication, when the extended

storage fuse switch is ON.

• BCM switches the status (shipping mode or normal mode) by itself according to the meter CAN signal*

from

combination meter, and transmits shipping mode status signal to combination meter via CAN communica-

tion.

• The combination meter displays extended storage fuse warning message*

on the odometer display, when

BCM is in shipping mode.

• BCM control functions are limited in shipping mode. Refer to

BCS-93, "Description"

*1: Odometer signal, wake up signal and each signal.

*2: When shipping mode function operates, “SHIP

→

PHASE

→

PUSH

→

FUSE In” is displayed.

Work Procedure

INFOID:0000000012200729

SHIPPING MODE CANCEL OPERATION

1. Turn ignition switch OFF.

2. Push in (switch on) the extended storage fuse switch. Refer to

PG-100, "How To Check"

3. Turn ignition switch ON.

4. Turn ignition switch OFF and wait at least 2 seconds.

>> GO TO 2.

SHIPPING MODE CANCEL CHECK

1. Turn ignition switch ON.

2. Check that extended storage fuse warning message is not displayed on odometer display.

>> WORK END

JMMIA1311GB

Revision: November 2015

2016 JUKE

BCS

U1000 CAN COMM

BCS-83

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

DTC/CIRCUIT DIAGNOSIS

U1000 CAN COMM

Description

INFOID:0000000012200730

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-

tiplex communication line with high data communication speed and excellent error detection ability. Modern

vehicle is equipped with many electronic control unit, and each control unit shares information and links with

other control units during operation (not independent). In CAN communication, control units are connected

with 2 communication lines (CAN H-line, CAN L-line) allowing a high rate of information transmission with less

wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to

LAN-30, "CAN COMMUNICATION SYSTEM : CAN Communica-

tion Signal Chart"

DTC Logic

INFOID:0000000012200731

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000012200732

PERFORM SELF DIAGNOSTIC

1. Turn ignition switch ON and wait for 2 seconds or more.

2. Check “Self Diagnostic Result” of BCM.
Is DTC “U1000” displayed?

YES

>> Refer to

LAN-17, "Trouble Diagnosis Flow Chart"

>> Refer to

GI-45, "Intermittent Incident"

DTC

CONSULT display de-

scription

DTC Detection Condition

Possible cause

U1000

CAN COMM

When BCM cannot communicate CAN com-
munication signal continuously for 2 seconds
or more.

CAN communication system

Revision: November 2015

2016 JUKE

BCS-84

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

U1010 CONTROL UNIT (CAN)

U1010 CONTROL UNIT (CAN)

DTC Logic

INFOID:0000000012200733

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000012200734

REPLACE BCM

When DTC “U1010” is detected, replace BCM.

>> Replace BCM. Refer to

BCS-94, "Removal and Installation"

DTC

CONSULT display de-

scription

DTC Detection Condition

Possible cause

U1010

CONTROL UNIT (CAN)

BCM detected internal CAN communication circuit malfunction.

BCM

Revision: November 2015

2016 JUKE

Content .. 38 39 40 41 ..