Infiniti FX35, FX50 (S51). Manual - part 952

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  950  951  952  953   ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 952

 

 

EM-108

< UNIT DISASSEMBLY AND ASSEMBLY >

[VQ35HR]

CYLINDER HEAD

• Rear timing chain case: Refer to 

EM-95, "Exploded View"

.

• Camshaft: Refer to 

EM-70, "Exploded View"

.

2.

Remove cylinder head.
• Loosen cylinder head bolts in reverse order as shown in the

figure with cylinder head bolt wrench (commercial service tool)
and power tool.

3.

Remove cylinder head gaskets.

4.

Remove valve lifter.
• Identify installation positions, and store them without mixing them up.

5.

Remove valve collet.
• Compress valve spring with the valve spring compressor [SST:

KV10116200 (J-26336-A)] (A), the attachment [SST:
KV10115900 (J-26336-20)] (C) and the adapter [SST:
KV10109220 (

)] (B). Remove valve collet with a magnet

hand.

CAUTION:

When working, take care not to damage valve lifter holes.

6.

Remove valve spring retainer, valve spring and valve spring seat.

7.

Push valve stem to combustion chamber side, and remove valve.
• Identify installation positions, and store them without mixing them up.

8.

Remove valve oil seal using the valve oil seal puller [SST:
KV10107902 (J-38959)] (A).

9.

Remove valve seat, if valve seat must be replaced.

A

:  Bank  1

B

:  Bank  2

: Engine front

JPBIA0172ZZ

JPBIA0180ZZ

JPBIA0177ZZ

CYLINDER HEAD

EM-109

< UNIT DISASSEMBLY AND ASSEMBLY >

[VQ35HR]

C

D

E

F

G

H

I

J

K

L

M

A

EM

N

P

O

• Bore out old seat until it collapses. Boring should not continue beyond the bottom face of the seat

recess in cylinder head. Set the machine depth stop to ensure this. Refer to 

EM-145, "Cylinder Head"

.

CAUTION:

Prevent to scratch cylinder head by excessive boring.

10. Remove valve guide, if valve guide must be replaced.
a.

To remove valve guide, heat cylinder head to 110 to 130

°

C (230

to 266

°

F) by soaking in heated oil (A).

b.

Drive out valve guide with a press [under a 20 kN (2 ton, 2.2 US
ton, 2.0 lmp ton) pressure] or a hammer and the valve guide drift
(commercial service tool).

WARNING:

Cylinder head contains heat. When working, wear protec-
tive equipment to avoid getting burned.

11. Remove spark plug tube, if necessary.

• Using a pliers, pull spark plug tube out of cylinder head. 

CAUTION:

• Take care not to damage cylinder head.
• Once removed, spark plug tube will be deformed and cannot be reused. Never remove it unless

absolutely necessary.

ASSEMBLY

1.

If valve guide is removed in step 10 (DISASSEMBLY), install it. 
Replace with oversized [0.2 mm (0.008 in)] valve guide.

a.

Using the valve guide reamer (commercial service tool) (A),
ream cylinder head valve guide hole.

JPBIA0184ZZ

SEM931C

Valve guide hole diameter (for service parts):

Intake and exhaust

: Refer to 

EM-145, "Cylinder Head"

.

JPBIA0185ZZ

EM-110

< UNIT DISASSEMBLY AND ASSEMBLY >

[VQ35HR]

CYLINDER HEAD

b.

Heat cylinder head to 110 to 130

°

C (230 to 266

°

F) by soaking in

heated oil (A).

c.

Using the valve guide drift (commercial service tool), press valve
guide from camshaft side to the dimensions as shown in the fig-
ure.

WARNING:

Cylinder head contains heat. When working, wear protec-
tive equipment to avoid getting burned.

d.

Using the valve guide reamer (commercial service tool) (A),
apply reamer finish to valve guide.

2.

If valve seat is removed in step 9 (DISASSEMBLY), install it. 
Replace with oversize [0.5 mm (0.020 in)] valve seat.

a.

Ream cylinder head recess diameter (a) for service valve seat.

• Be sure to ream in circles concentric to valve guide center.

This enables valve to fit correctly.

JPBIA0184ZZ

Projection (A)

Intake and exhaust

: Refer to 

EM-145, "Cylinder Head"

.

JPBIA0186ZZ

Standard

: Refer to 

EM-145, 

"Cylinder Head"

.

(Intake and exhaust)

JPBIA0185ZZ

Oversize

: Refer to 

EM-145, 

"Cylinder Head"

.

(Intake and exhaust)

JPBIA0188ZZ

CYLINDER HEAD

EM-111

< UNIT DISASSEMBLY AND ASSEMBLY >

[VQ35HR]

C

D

E

F

G

H

I

J

K

L

M

A

EM

N

P

O

b.

Heat cylinder head to 110 to 130

°

C (230 to 266

°

F) by soaking in

heated oil (A).

c.

Provide valve seats cooled well with dry ice. Force fit valve seat into cylinder head.

WARNING:

Cylinder head contains heat. When working, wear protective equipment to avoid getting burned.

CAUTION:

Never directly touching cold valve seats.

d.

Using the valve seat cutter set (commercial service tool) or valve
seat grinder, finish seat to the specified dimensions. Refer to

EM-145, "Cylinder Head"

.

CAUTION:

When using the valve seat cutter, firmly grip cutter handle
with both hands. Then, press on the contacting surface all
around the circumference to cut in a single drive. Improper
pressure on with cutter or cutting many different times may
result in stage valve seat. 

e.

Using compound, grind to adjust valve fitting. 

f.

Check again for normal contact. 

3.

Install new valve oil seals as per the following:

a.

Apply new engine oil on valve oil seal joint and seal lip.

b.

Install with the valve oil seal drift [SST: KV10115600 (J-38958)]
(A) to match dimension in the figure.

4.

Install valve spring seat.

5.

Install valve.
NOTE:
Larger diameter valves are for intake side.

6.

Install valve spring (uneven pitch type).

JPBIA0184ZZ

SEM934C

Height (b) (Without valve spring seat installed)

Intake and exhaust

: 14.3 - 14.9 mm (0.563 - 0.587 in)

JPBIA0178ZZ

 

 

 

 

 

 

 

Content   ..  950  951  952  953   ..