Infiniti FX35, FX50 (S51). Manual - part 715

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  713  714  715  716   ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 715

 

 

P1551, P1552 BATTERY CURRENT SENSOR

EC-401

< DTC/CIRCUIT DIAGNOSIS >

[VQ35HR]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P1551, P1552 BATTERY CURRENT SENSOR

Description

INFOID:0000000005237007

The power generation voltage variable control enables fuel consumption to be decreased by reducing the
engine load which is caused by the power generation of the generator. The battery current sensor is installed
to the battery cable at the negative terminal. The sensor measures the charging/discharging current of the bat-
tery. Based on the sensor signal, ECM judges whether or not the power generation voltage variable control is
performed. When performing the power generation voltage variable control, ECM calculates the target power
generation voltage based on the sensor signal. And ECM sends the calculated value as the power generation
command value to IPDM E/R. For the details of the power generation voltage variable control, refer to 

CHG-8,

"System Description"

.

CAUTION:

Never connect the electrical component or the ground wire directly to the battery terminal. The con-
nection causes the malfunction of the power generation voltage variable control, and then battery dis-
charge may occur.

DTC Logic

INFOID:0000000005237008

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.

Turn ignition switch OFF and wait at least 10 seconds.

2.

Turn ignition switch ON.

3.

Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V with ignition
switch ON

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON and wait at least 10 seconds.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1551

Battery current sensor circuit 
low input

An excessively low voltage from the sen-
sor is sent to ECM.

• Harness or connectors

(Battery current sensor circuit is open 
or shorted.)
[Crankshaft position (CKP) sensor cir-
cuit is shorted.]
[Camshaft position (CMP) sensor 
(bank 2) circuit is shorted.]
[Exhaust valve timing (EVT) control po-
sition sensor (bank 2) circuit is short-
ed.]
[Accelerator pedal position (APP) sen-
sor 2 circuit is shorted.]
(EVAP control system pressure sensor 
circuit is shorted.)
(Refrigerant pressure sensor circuit is 
shorted.)

• Battery current sensor
• CKP sensor
• CMP sensor (bank 2)
• EVT control position sensor (bank 2)
• APP sensor
• EVAP control system pressure sensor
• Refrigerant pressure sensor

P1552

Battery current sensor circuit 
high input

An excessively high voltage from the sen-
sor is sent to ECM.

EC-402

< DTC/CIRCUIT DIAGNOSIS >

[VQ35HR]

P1551, P1552 BATTERY CURRENT SENSOR

2.

Check 1st trip DTC.

Is 1st trip DTC detected?

YES

>> Go to 

EC-402, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005237009

1.

CHECK GROUND CONNECTION

1.

Turn ignition switch OFF.

2.

Check ground connection M95. Refer to Ground Inspection in 

GI-39, "Circuit Inspection"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace ground connection.

2.

CHECK BATTERY CURRENT SENSOR POWER SUPPLY CIRCUIT-I

1.

Disconnect battery current sensor harness connector.

2.

Turn ignition switch ON.

3.

Check the voltage between battery current sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> GO TO 3.

3.

CHECK BATTERY CURRENT SENSOR POWER SUPPLY CIRCUIT-II

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between battery current sensor harness connector and ECM harness connector.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 4.

4.

DETECT MALFUNCTIONING PART

Check the following.
• Harness connectors F1, E3
• Harness for open between battery current sensor and ECM

>> Repair open circuit.

5.

CHECK SENSOR POWER SUPPLY CIRCUIT

Check harness for short to power and short to ground, between the following terminals.

Battery current sensor

Ground

Voltage (V)

Connector

Terminal

E21

1

Ground

Approx. 5

Battery current sensor

ECM

Continuity

Connector

Terminal

Connector

Terminal

E21

1

F102

64

Existed

ECM

Sensor

Connector

Terminal

Name

Connector

Terminal

F101

46

Crankshaft position (CKP) sensor

F2

1

P1551, P1552 BATTERY CURRENT SENSOR

EC-403

< DTC/CIRCUIT DIAGNOSIS >

[VQ35HR]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair short to ground or short to power in harness or connectors.

6.

CHECK COMPONENTS

Check the following.
• CKP sensor (Refer to 

EC-271, "Component Inspection"

.)

• CMP sensor (bank 2) (Refer to 

EC-277, "Component Inspection"

.)

• EVT control position sensor (bank 2) (Refer to 

EC-369, "Component Inspection"

.)

• EVAP control system pressure sensor (Refer to 

EC-313, "Component Inspection"

.)

• Refrigerant pressure sensor (Refer to 

HAC-84, "Diagnosis Procedure"

.)

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace malfunctioning component.

7.

CHECK APP SENSOR

Refer to 

EC-444, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 14.

NO

>> GO TO 8.

8.

REPLACE ACCELERATOR PEDAL ASSEMBLY

1.

Replace accelerator pedal assembly.

2.

Go to 

EC-445, "Special Repair Requirement"

.

>> INSPECTION END

9.

CHECK BATTERY CURRENT SENSOR GROUND CIRCUIT FOR OPEN AND SHORT

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between battery current sensor harness connector and ECM harness connector.

4.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 11.

NO

>> GO TO 10.

10.

DETECT MALFUNCTIONING PART

Check the following.

F102

64

Camshaft position (CMP) sensor (bank 2)

F18

1

Exhaust valve timing (EVT) control position 
sensor (bank 2)

F19

1

Battery current sensor

E21

1

M107

103

Accelerator pedal position (APP) sensor

E112

(Without ICC)

6

E116

(with ICC)

3

107

EVAP control system pressure sensor

B252

3

111

Refrigerant pressure sensor

E77

3

ECM

Sensor

Connector

Terminal

Name

Connector

Terminal

Battery current sensor

ECM

Continuity

Connector

Terminal

Connector

Terminal

E21

2

F102

95

Existed

EC-404

< DTC/CIRCUIT DIAGNOSIS >

[VQ35HR]

P1551, P1552 BATTERY CURRENT SENSOR

• Harness connectors F1, E3
• Harness for open or short between battery current sensor and ECM

>> Repair open circuit, short to ground or short to power in harness or connectors.

11.

CHECK BATTERY CURRENT SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Check the continuity between battery current sensor harness connector and ECM harness connector.

2.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 13.

NO

>> GO TO 12.

12.

DETECT MALFUNCTIONING PART

Check the following.
• Harness connectors F1, E3
• Harness for open or short between battery current sensor and ECM

>> Repair open circuit, short to ground or short to power in harness or connectors.

13.

CHECK BATTERY CURRENT SENSOR

Refer to 

EC-404, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 14.

NO

>> Replace battery negative cable assembly.

14.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-36, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000005237010

1.

CHECK BATTERY CURRENT SENSOR

1.

Turn ignition switch OFF.

2.

Reconnect harness connectors disconnected.

3.

Disconnect battery negative cable (1).

4.

Install jumper cable (A) between battery negative terminal and
body ground.

5.

Turn ignition switch ON.

6.

Check the voltage between ECM harness connector terminals
under the following conditions.

Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to 

PG-3, "How to Handle Battery"

.

Battery current sensor

ECM

Continuity

Connector

Terminal

Connector

Terminal

E21

3

F102

91

Existed

: To body ground

ECM

Voltage (V)

Connector

+

Terminal

Terminal

F102

91

(Battery current sensor signal)

95

Approx. 2.5

JMBIA1512ZZ

 

 

 

 

 

 

 

Content   ..  713  714  715  716   ..