Infiniti FX35, FX50 (S51). Manual - part 577

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  575  576  577  578   ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 577

 

 

PREPARATION

DLN-143

< PREPARATION >

[FRONT FINAL DRIVE: F160A]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000005249183

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Tool number
(Kent-Moore No.)
Tool name

Description

KV381054S0
(J-34286)
Puller

• Removing side oil seal (right side)
• Removing side bearing outer race

ST33400001
(J-26082)
Drift
a: 60 mm (2.36 in) dia.
b: 47 mm (1.85 in) dia.

• Installing side oil seal (right side)
• Installing front oil seal

KV38102100
(J-25803-01)
Drift
a: 44 mm (1.73 in) dia.
b: 36 mm (1.42 in) dia.
c: 24.5 mm (0.965 in) dia.

Installing side oil seal (left side)

KV38100200
(

)

Drift
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.

Installing side shaft oil seal

ST30032000
(J-26010-01)
Drift
a: 80 mm (3.15 in) dia.
b: 38 mm (1.50 in) dia.
c: 31 mm (1.22 in) dia.

• Installing side shaft
• Installing pinion rear bearing inner race

KV10111100
(J-37228)
Seal cutter

Removing carrier cover

ZZA0601D

ZZA0702D

ZZA1046D

ZZA1143D

S-NT107

S-NT046

DLN-144

< PREPARATION >

[FRONT FINAL DRIVE: F160A]

PREPARATION

ST3306S001
(J-22888-D)
Differential side bearing puller set
1: ST33051001

(J-22888-20)
Puller

2: ST33061000

(J-8107-2)
Base
a: 28.5 mm (1.122 in) dia.
b: 38 mm (1.50 in) dia.

Removing and installing side bearing inner 
race

ST33230000
(J-25805-01)
Drift
a: 51 mm (2.01 in) dia.
b: 41 mm (1.61 in) dia.
c: 28.5 mm (1.122 in) dia.

Installing side bearing inner race

ST30611000
(J-25742-1)
Drift bar

Installing side bearing outer race (Use with 
KV31103000)

KV31103000
(J-38982)
Drift
a: 49 mm (1.93 in) dia.
b: 70 mm (2.76 in) dia.

Installing side bearing outer race

ST3127S000
(J-25765-A)
Preload gauge

Measuring pinion bearing preload and total 
preload

(J-8129)
Spring gauge

Measuring turning torque

Tool number
(Kent-Moore No.)
Tool name

Description

NT072

ZZA1046D

S-NT090

ZZA1113D

ZZA0806D

NT127

PREPARATION

DLN-145

< PREPARATION >

[FRONT FINAL DRIVE: F160A]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

Commercial Service Tools

INFOID:0000000005249184

ST37820000
(

)

Drift
a: 39 mm (1.54 in) dia.
b: 72 mm (2.83 in) dia.

Installing pinion front and rear bearing outer 
race

KV38102510
(

)

Drift
a: 71 mm (2.80 in) dia.
b: 65 mm (2.56 in) dia.

Installing front oil seal

Tool number
(Kent-Moore No.)
Tool name

Description

ZZA0836D

ZZA0838D

Tool name

Description

Flange wrench

Removing and installing drive pinion lock nut

Replacer

Removing pinion rear bearing inner race

Spacer
a: 60 mm (2.36 in) dia.
b: 36 mm (1.42 in) dia.
c: 30 mm (1.18 in)

Installing pinion front bearing inner race

Power tool

Loosening bolts and nuts

NT035

ZZA0700D

ZZA1133D

PBIC0190E

DLN-146

< PERIODIC MAINTENANCE >

[FRONT FINAL DRIVE: F160A]

FRONT DIFFERENTIAL GEAR OIL

PERIODIC MAINTENANCE

FRONT DIFFERENTIAL GEAR OIL

Inspection

INFOID:0000000005249186

OIL LEAKAGE

Make sure that oil is not leaking from final drive assembly or around it.

OIL LEVEL

• Remove filler plug (1) and check oil level from filler plug mounting

hole as shown in the figure.

CAUTION:

Never start engine while checking oil level.

• Set a gasket on filler plug (1) and install it on final drive assembly.

Refer to 

DLN-153, "Exploded View"

.

CAUTION:

Never reuse gasket.

Draining

INFOID:0000000005249187

1.

Stop engine.

2.

Remove drain plug (1) and drain gear oil.

3.

Set a gasket on drain plug (1) and install it to final drive assem-
bly and tighten to the specified torque. Refer to 

DLN-153,

"Exploded View"

.

CAUTION:

Never reuse gasket.

Refilling

INFOID:0000000005249188

1.

Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified level near filler plug mounting hole.

2.

After refilling oil, check oil level. Set a gasket to filler plug (1),
then install it to final drive assembly. Refer to 

DLN-153,

"Exploded View"

.

CAUTION:

Never reuse gasket.

JPDID0188ZZ

JPDID0189ZZ

Oil grade and Viscosity

: Refer to 

MA-12, "Fluids 

and Lubricants"

.

Oil capacity

: Refer to 

DLN-182, "Gen-

eral Specifications"

.

JPDID0188ZZ

 

 

 

 

 

 

 

Content   ..  575  576  577  578   ..