Infiniti FX35, FX50 (S51). Manual - part 566

FRONT DRIVE SHAFT AND DRIVE CHAIN

DLN-99

< UNIT DISASSEMBLY AND ASSEMBLY >

[TRANSFER: ETX13C]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

3.

Install front drive shaft rear bearing with the drift (A) [SST:
KV38104010 (

—

)].

4.

Set drive chain to front drive shaft.

CAUTION:

Identification mark (A) of drive chain should be in the side
of front bearing (1) of front drive shaft.

5.

Install drive chain to main shaft, and then install front drive shaft.

CAUTION:

Never use tools. Always install by hand.

6.

Install front case to rear case. Refer to 

DLN-73, "VQ35HR :

Assembly"

.

VQ35HR : Inspection

INFOID:0000000005525036

Check items below. If necessary, replace them with new ones.

CASES

• Contact surfaces of bearing for wear, damage, etc.
• Damage and cracks of case.

BEARING

Damage and rough rotation of bearing.

SHAFT

JPDIE0139ZZ

JPDIE0075ZZ

JPDIE0120ZZ

PDIA0300E

DLN-100

< UNIT DISASSEMBLY AND ASSEMBLY >

[TRANSFER: ETX13C]

FRONT DRIVE SHAFT AND DRIVE CHAIN

Damage, peeling, dent, uneven wear, bending, etc. of shaft.

GEARS AND CHAIN

• Excessive wear, damage, peeling, etc. of gear and chain.
• Cracks, damage, wear, etc of drive chain.

VK50VE

JPDIE0143ZZ

JPDIE0136ZZ

FRONT DRIVE SHAFT AND DRIVE CHAIN

DLN-101

< UNIT DISASSEMBLY AND ASSEMBLY >

[TRANSFER: ETX13C]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

VK50VE : Exploded View

INFOID:0000000005249137

1.

Plug

2.

Drive chain

3.

Front drive shaft rear bearing

4.

Front drive shaft

5.

Front drive shaft front bearing

6.

Sprocket

7.

Needle bearing

8.

Main shaft

9.

Oil pump

10. Spacer

11.

Steel ball

12. Snap ring

13. Snap ring

14. Main shaft bearing

15. Front case

16. Main shaft oil seal

17. Front oil seal

18. Spacer

19. Snap ring

20. Circlip

21. Electric controlled coupling

22. Oil cover

23. O-ring

24. Retainer

25. Transfer fluid temperature sensor

26. Baffle plate

27. Spacer

28. Snap ring

29. Dowel pin

30. Rear case

31. Harness bracket

32. Breather tube

33. Filler plug

34. Gasket

35. Drain plug

36. Rear bearing

37. Snap ring

38. Spacer

39. Rear oil seal

40. Companion flange

41. Self-lock nut

A.

Oil seal lip

B.

Matching surface

: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to 

GI-16, "Recommended Chemical Products and Sealants"

.

: Apply petroleum jelly.

JPDIE0196GB

DLN-102

< UNIT DISASSEMBLY AND ASSEMBLY >

[TRANSFER: ETX13C]

FRONT DRIVE SHAFT AND DRIVE CHAIN

VK50VE : Disassembly

INFOID:0000000005249138

1.

Separate front case and rear case. Refer to 

DLN-79, "VK50VE : Disassembly"

.

2.

Remove drive chain and front drive shaft.

CAUTION:

Never use tools. Always remove by hand.

3.

Remove front drive shaft front bearing with the drift (A) and
replacer (B).

4.

Remove front drive shaft rear bearing with the drift (A) and
replacer (B).

5.

Remove plug from front drive shaft.

VK50VE : Assembly

INFOID:0000000005249139

1.

Install plug to front drive shaft.

CAUTION:

Never reuse plug.

2.

Install front drive shaft front bearing with the drift (A) [SST:
ST33200000 (J-26082)].

: Apply transfer fluid. Refer to 

MA-12, "Fluids and Lubricants"

.

Refer to 

GI-4, "Components"

 for symbols not described above.

A:

Drift [SST: ST31214000 (J-25269-B)]

B:

replacer (commercial service tool)

JPDIE0084ZZ

A:

Drift [SST: ST31214000 (J-25269-B)]

B:

replacer (commercial service tool)

JPDIE0085ZZ

JPDIE0138ZZ