Infiniti FX35, FX50 (S51). Manual - part 555

PREPARATION

DLN-55

< PREPARATION >

[TRANSFER: ETX13C]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

Replacer

• Remove companion flange
• Removing front drive shaft front bearing
• Removing front drive shaft rear bearing

Power tool

Loosening bolts and nuts

Tool name

Description

ZZB0823D

PBIC0190E

DLN-56

< PERIODIC MAINTENANCE >

[TRANSFER: ETX13C]

TRANSFER FLUID

PERIODIC MAINTENANCE

TRANSFER FLUID

VQ35HR

VQ35HR : Inspection

INFOID:0000000005249099

FLUID LEAKAGE

Check transfer surrounding area (oil seal, drain plug, and filler plug etc.) for fluid leakage.

FLUID LEVEL

1.

Remove filler plug (1) and gasket. Then check that fluid is filled
up from mounting hole for the filler plug.

CAUTION:

Never start engine while checking fluid level.

2.

Set a new gasket onto filler plug, and install it on transfer and
tighten to the specified torque. Refer to 

DLN-69, "VQ35HR :

Exploded View"

.

CAUTION:

Never reuse gasket.

VQ35HR : Draining

INFOID:0000000005249100

1.

Run the vehicle to warm up the transfer unit sufficiently.

2.

Stop the engine, and remove the drain plug (1) to drain the
transfer fluid.

3.

Set a new gasket onto the drain plug, and install it on the trans-
fer and tighten to the specified torque. Refer to 

DLN-69,

"VQ35HR : Exploded View"

.

CAUTION:

Never reuse gasket.

VQ35HR : Refilling

INFOID:0000000005249101

1.

Remove filler plug (1) and gasket. Then fill fluid up to mounting
hole for the filler plug.

CAUTION:

Carefully fill the fluid. (Fill up for approximately 3 minutes.)

2.

Leave the vehicle for 3 minutes, and check the fluid level again.

3.

Set a new gasket onto filler plug, and install it on transfer and
tighten to the specified torque. Refer to 

DLN-69, "VQ35HR : Exploded View"

.

CAUTION:

Never reuse gasket.

VK50VE

JPDIE0129ZZ

JPDIE0130ZZ

Fluid and viscosity

: Refer to 

MA-12, "Fluids 

and Lubricants"

.

Fluid capacity

: Refer to 

DLN-105, "Gen-

eral Specifications"

.

JPDIE0129ZZ

TRANSFER FLUID

DLN-57

< PERIODIC MAINTENANCE >

[TRANSFER: ETX13C]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

VK50VE : Inspection

INFOID:0000000005249102

FLUID LEAKAGE

Check transfer surrounding area (oil seal, drain plug, and filler plug etc.) for fluid leakage.

FLUID LEVEL

1.

Remove filler plug (1) and gasket. Then check that fluid is filled
up from mounting hole for the filler plug.

CAUTION:

Never start engine while checking fluid level.

2.

Set a new gasket onto filler plug, and install it on transfer and
tighten to the specified torque. Refer to 

DLN-78, "VK50VE :

Exploded View"

.

CAUTION:

Never reuse gasket.

VK50VE : Draining

INFOID:0000000005249103

1.

Run the vehicle to warm up the transfer unit sufficiently.

2.

Stop the engine, and remove the drain plug (1) to drain the
transfer fluid.

3.

Set a new gasket onto the drain plug, and install it on the trans-
fer and tighten to the specified torque. Refer to 

DLN-78,

"VK50VE : Exploded View"

.

CAUTION:

Never reuse gasket.

VK50VE : Refilling

INFOID:0000000005249104

1.

Remove filler plug (1) and gasket. Then fill fluid up to mounting
hole for the filler plug.

CAUTION:

Carefully fill the fluid. (Fill up for approximately 3 minutes.)

2.

Leave the vehicle for 3 minutes, and check the fluid level again.

3.

Set a new gasket onto filler plug, and install it on transfer and
tighten to the specified torque. Refer to 

DLN-78, "VK50VE : Exploded View"

.

CAUTION:

Never reuse gasket.

JSDIA0788ZZ

JSDIA0789ZZ

Fluid and viscosity

: Refer to 

MA-12, "Fluids 

and Lubricants"

.

Fluid capacity

: Refer to 

DLN-105, "Gen-

eral Specifications"

.

JSDIA0788ZZ

DLN-58

< REMOVAL AND INSTALLATION >

[TRANSFER: ETX13C]

AWD CONTROL UNIT

REMOVAL AND INSTALLATION

AWD CONTROL UNIT

Exploded View

INFOID:0000000005249105

Removal and Installation

INFOID:0000000005249106

REMOVAL

1.

Remove the glove box assembly. Refer to 

IP-11, "Exploded View"

.

2.

Disconnect AWD control unit harness connector.

3.

Remove AWD control unit (1) mounting nuts.

4.

Remove AWD control unit.

INSTALLATION

Install in the reverse order of removal.

1.

AWD control unit

: Vehicle front

JSDIA0050ZZ

JSDIA0051ZZ