Infiniti FX35, FX50 (S51). Manual - part 534

BACK DOOR

DLK-259

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

BACK DOOR

BACK DOOR ASSEMBLY

BACK DOOR ASSEMBLY : Exploded View

INFOID:0000000005239747

REMOVAL

ADJUSTMENT

1.

Back door hinge cover (LH/RH)

2.

Back door hinge (LH/RH)

3.

Back door stay bracket (LH/RH)

4.

Back door stay (LH/RH)

5.

Back door weather-strip

6.

Stud ball (LH/RH)

7.

Bumper rubber (LH/RH)

8.

Back door striker

9.

Back door lock assembly

10. Back door assembly

A

:  Center  mark

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA2642GB

DLK-260

< REMOVAL AND INSTALLATION >

BACK DOOR

BACK DOOR ASSEMBLY : Removal and Installation

INFOID:0000000005239748

CAUTION:

• Operate with two workers, because of its heavy weight.
• Use protective tape or shop cloth to protect from damage during removal and installation.
NOTE:
The back door harness constitute the back door assembly.

REMOVAL

1.

Remove back door finisher inner, back door plate and back door hinge cover. Refer to 

INT-32, "Removal

and Installation"

. 

2.

Remove clips of headlining at rear end. Refer to 

INT-24, "Removal and Installation"

.

3.

Disconnect connectors and bolts of back door harness.

4.

Remove back door grommet (LH), and then pull harness out of vehicle at roof panel hole.

5.

Remove back door plate, and then disconnect washer tube. Refer to 

INT-32, "Exploded View"

 and 

WW-

129, "Removal and Installation"

.

6.

Pull washer tube out of back door.

7.

Support back door lock with the proper material to prevent it from falling.

WARNING:

Bodily injury may occur if no supporting rod is holding the back door open when removing the
back door stay.

8.

Remove back door stay. Refer to 

DLK-264, "BACK DOOR STAY : Removal and Installation"

.

9.

Remove back door hinge mounting bolts on back door and remove back door assembly.

1.

Back door assembly

2.

Bumper rubber

3.

Back door hinge

4.

Back door striker

5.

Roof

6.

Rear bumper fascia

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA2643GB

BACK DOOR

DLK-261

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• Check back door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, check back door open/close, lock/unlock operation.
• After installation, perform the fitting adjustment. Refer to 

DLK-261, "BACK DOOR ASSEMBLY :

Adjustment"

.

• After installation, perform the camera image calibration. Refer to 

AV-245, "CALIBRATING CAMERA

IMAGE (AROUND VIEW MONITOR) : Work Procedure"

 (single monitor) or 

AV-462, "CALIBRATING

CAMERA IMAGE (AROUND VIEW MONITOR) : Work Procedure"

 (twin monitor).

BACK DOOR ASSEMBLY : Adjustment

INFOID:0000000005239749

Check the clearance and the surface height between back door and each part by seeing and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.

Unit: mm (in)

1.

Remove back door hinge cover. Refer to 

INT-32, "Removal and Installation"

.

2.

Loosen back door hinge mounting bolts (back door side).

3.

Loosen bumper rubber.

4.

Remove luggage rear plate mask. Refer to 

INT-29, "Removal and Installation"

.

5.

Loosen back door striker mounting bolts.

6.

Lift up back door approximately 100 – 150 mm (3.937 – 5.906 in) height then close it lightly and check that
it is engaged firmly with back door closed.

7.

Check the clearance and surface height.

8.

Finally tighten back door hinge, bumper rubber, and back door striker.

CAUTION:

• Check back door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, check back door open/close, lock/unlock operation.

9.

Install back door hinge cover and luggage rear plate mask. Refer to 

INT-32, "Removal and Installation"

and 

INT-29, "Removal and Installation"

.

BACK DOOR STRIKER ADJUSTMENT

Adjust back door striker so that it becomes parallel with back door lock insertion direction.

BACK DOOR STRIKER

Portion

Standard

Back door – Roof

A – A

D

Clearance

5.0 – 9.0 (0.197 – 0.354)

E

Surface height

−

0.4 – 3.6 (

−

0.016 – 0.142)

Back door – Rear bumper fascia

B – B

F

Clearance

3.0 – 7.0 (0.118 – 0.276)

G

Surface height

−

2.1 – 2.1 (

−

0.083 – 0.083)

C – C

H

Clearance

5.0 – 9.0 (0.197 – 0.354)

DLK-262

< REMOVAL AND INSTALLATION >

BACK DOOR

BACK DOOR STRIKER : Exploded View

INFOID:0000000005239750

BACK DOOR STRIKER : Removal and Installation

INFOID:0000000005239751

REMOVAL

1.

Remove luggage rear plate mask. Refer to 

INT-29, "Removal and Installation"

.

2.

Remove mounting bolts, and then remove back door striker.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• After installation, check back door open/close, lock/unlock operation.
• After installation, perform the fitting adjustment. Refer to 

DLK-261, "BACK DOOR ASSEMBLY :

Adjustment"

.

BACK DOOR HINGE

1.

Back door hinge cover (LH/RH)

2.

Back door hinge (LH/RH)

3.

Back door stay bracket (LH/RH)

4.

Back door stay (LH/RH)

5.

Back door weather-strip

6.

Stud ball (LH/RH)

7.

Bumper rubber (side) (LH/RH)

8.

Back door striker

9.

Back door lock assembly

10. Back door assembly

A

:  Center  mark

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA2642GB