Infiniti FX35, FX50 (S51). Manual - part 483

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  481  482  483  484   ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 483

 

 

DIAGNOSIS SYSTEM (BCM)

DLK-55

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

SELF-DIAG RESULT

Monitor item

Description

REMO CONT ID CONFIR

It can be checked whether Intelligent Key ID code is registered or not in this mode.

AUTO LOCK SET

Auto door lock time can be changed in this mode.
• MODE 1: 1 min.
• MODE 2: 5 min.
• MODE 3: 30 sec.
• MODE 4: 2 min.

WELCOME LIGHT OP SET

Welcome light function mode can be changed to operate (WITH) or not operate (WITHOUT) 
in this mode.

LOCK/UNLOCK BY I-KEY

Door lock/unlock function by door request switch (driver side, passenger side and back door) 
mode can be changed to operate (WITH) or not operate (WITHOUT) in this mode.

ENGINE START BY I-KEY

Engine start function mode can be changed to operate (WITH) or not operate (WITHOUT) in 
this mode. 

TRUNK/GLASS HATCH OPEN

Buzzer reminder function mode by back door request switch can be changed to operate (ON) 
or not operate (OFF) in this mode.

PANIC ALARM SET

Panic alarm button pressing time on Intelligent Key remote control button can be selected from 
the following in this mode. 
• MODE 1: 0.5 sec.
• MODE 2: Non-operational
• MODE 3: 1.5 sec.

PW DOWN SET

Unlock button pressing time on Intelligent Key button can be selected from the following in this 
mode. 
• MODE 1: 3 sec.
• MODE 2: Non-operational
• MODE 3: 5 sec.

TRUNK OPEN DELAY

NOTE:
This item is displayed, but cannot be supported. 

LO- BATT OF KEY FOB WARN

Intelligent Key low battery warning mode can be changed to operate (WITH) or not operate 
(WITHOUT) with this mode. 

ANTI KEY LOCK IN FUNCTI

Key reminder function mode can be changed to operate (WITH) or not operate (WITHOUT) 
with this mode.

HAZARD ANSWER BACK

Hazard reminder function mode can be selected from the following in this mode.
• LOCK ONLY: Door lock operation only
• UNLOCK ONLY: Door unlock operation only
• LOCK/UNLOCK: Lock/unlock operation
• OFF: Non-operational

ANS BACK I-KEY LOCK

Buzzer reminder function (lock operation) mode by door request switch (driver side and pas-
senger side) can be selected from the following in this mode. 
• Horn chirp: Sound horn
• Buzzer: Sound Intelligent Key warning buzzer
• OFF: Non-operational

ANS BACK I-KEY UNLOCK

Buzzer reminder function (unlock operation) mode by door request switch can be changed to 
operate (ON) or not operate (OFF) in this mode.

SHORT CRANKING OUTPUT

Starter motor can operate during the times below.
• 70 msec.
• 100  msec.
• 200  msec.

INSIDE ANT DIAGNOSIS

This function allows inside key antenna self-diagnosis.

HORN WITH KEYLESS LOCK

Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not 
operate (OFF) in this mode.

WELCOME LIGHT SELECT

Welcome light function mode can be selected from the following in this mode.
• Puddle Lamp (ON/OFF)
• Room Lamp (ON/OFF)
• Head and Tail Lamps (This item is displayed, but cannot be supported.)
• Outside Handle (This item is displayed, but cannot be supported.)

DLK-56

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM)

Refer to 

DLK-183, "DTC Index"

.

DATA MONITOR

Monitor Item

Condition

REQ SW -DR

Indicates [ON/OFF] condition of door request switch (driver side).

REQ SW -AS

Indicates [ON/OFF] condition of door request switch (passenger side).

REQ SW -BD/TR

Indicates [ON/OFF] condition of back door request switch.

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch.

IGN RLY2 -F/B

Indicates [ON/OFF] condition of ignition relay 2.

CLUCH SW

NOTE:
This item is displayed, but cannot be monitored. 

BRAKE SW 1

Indicates [ON/OFF] condition of brake switch.

DETE/CANCL SW

Indicates [ON/OFF] condition of the P position.

SFT PN/N SW

Indicates [ON/OFF] condition of the P or N position.

S/L -LOCK

Indicates [ON/OFF] condition of steering lock unit (LOCK).

S/L -UNLOCK

Indicates [ON/OFF] condition of steering lock unit (UNLOCK).

S/L RELAY -F/B

Indicates [ON/OFF] condition of ignition switch.

UNLK SEN -DR

Indicates [ON/OFF] condition of driver door UNLOCK status.

PUSH SW -IPDM

Indicates [ON/OFF] condition of push-button ignition switch.

IGN RLY1 -F/B

Indicates [ON/OFF] condition of ignition relay 1.

DETE SW -IPDM

Indicates [ON/OFF] condition of the P position.

SFT PN -IPDM

Indicates [ON/OFF] condition of the P or N position.

SFT P -MET

Indicates [ON/OFF] condition of the P position.

SFT N -MET

Indicates [ON/OFF] condition of the N position.

ENGINE STATE

Indicates [STOP/START/CRANK/RUN] condition of engine states.

S/L LOCK-IPDM

Indicates [ON/OFF] condition of steering lock unit (LOCK).

S/L UNLK-IPDM

Indicates [ON/OFF] condition of steering lock unit (UNLOCK).

S/L RELAY-REQ

Indicates [ON/OFF] condition of steering lock relay.

VEH SPEED 1

Displays the vehicle speed signal received from unified meter and A/C amp. by numerical 
value [Km/h].

VEH SPEED 2

Displays the vehicle speed signal received from ABS or VDC or CVT by numerical value 
[Km/h].

DOOR STAT-DR

Indicates [LOCK/READY/UNLOCK] condition of driver side door status.

DOOR STAT-AS

Indicates [LOCK/READY/UNLOCK] condition of passenger side door status.

ID OK FLAG

Indicates [SET/RESET] condition of key ID.

PRMT ENG STRT

Indicates [SET/RESET] condition of engine start possibility.

PRMT RKE STRT

NOTE:
This item is displayed, but cannot be monitored. 

KEY SW -SLOT

Indicates [ON/OFF] condition of key slot.

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored. 

RKE-LOCK

Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.

RKE-UNLOCK

Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored. 

RKE-PANIC

Indicates [ON/OFF] condition of PANIC button of Intelligent Key.

RKE-P/W OPEN

Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key.

RKE-MODE CHG

Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.

DIAGNOSIS SYSTEM (BCM)

DLK-57

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

ACTIVE TEST

TRUNK

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on In-
telligent Key, the numerical values starts changing.

RKE OPE COUN2

NOTE:
This item is displayed, but cannot be monitored. 

Monitor Item

Condition

Test item

Description

BATTERY SAVER

This test is able to check interior room lamp operation.
The interior room lamp is activated when “ON” on CONSULT-III screen is touched.

PW REMOTO DOWN SET

This test is able to check power window down operation.
The power window down is activated when “ON” on CONSULT-III screen is touched.

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation.
The Intelligent Key warning buzzer is activated when “ON” on CONSULT-III screen is touched.

INSIDE BUZZER

This test is able to check warning chime in combination meter operation.
• Takes away warning chime sounds when “TAKE OUT” on CONSULT-III screen is touched.
• Key warning chime sounds when “KEY” on CONSULT-III screen is touched.
• The P position warning chime sounds when “KNOB” on CONSULT-III screen is touched.

INDICATOR

This test is able to check warning lamp operation.
• “KEY” Warning lamp illuminates when “RED ON” on CONSULT-III screen is touched.
• The “KEY” Warning lamp blinks when “RED IND” on CONSULT-III screen is touched.

INT LAMP

This test is able to check interior room lamp operation.
The interior room lamp is activated when “ON” on CONSULT-III screen is touched.

LCD

This test is able to check meter display information
• Engine start information displays when “BP N” on CONSULT-III screen is touched.
• Engine start information displays when “BP I” on CONSULT-III screen is touched.
• Key ID warning displays when “ID NG” on CONSULT-III screen is touched.
• Steering lock information displays when “ROTAT” on CONSULT-III screen is touched.
• The P position warning displays when “SFT P” on CONSULT-III screen is touched.
• Intelligent Key insert information displays when “INSRT” on CONSULT-III screen is touched.
• Intelligent Key low battery warning displays when “BATT” on CONSULT-III screen is touched.
• Take away through window warning displays when “NO KY” on CONSULT-III screen is touched.
• Take away warning displays when “OUTKY” on CONSULT-III screen is touched.
• The OFF position warning displays when “LK WN” on CONSULT-III screen is touched.

TRUNK/GLASS HATCH

This test is able to check back door opener actuator open operation.
This actuator operates when “ON” on CONSULT-III screen is touched.

BLINKER

This test is able to check security hazard lamp operation.
The hazard lamps is activated when “LH” or “RH” on CONSULT-III screen is touched.

HORN

This test is able to check horn operation.
The horn will be activated when “ON” on CONSULT-III screen is touched.

P RANGE

This test is able to check A/T shift selector power supply
A/T shift selector power is supplied when “ON” on CONSULT-III screen is touched.

ENGINE SW ILLUMI

This test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched.

LOCK INDICATOR

This test is able to check indicator in push-ignition switch operation.
Indicator in push-ignition switch (LOCK) illuminates when “ON” on CONSULT-III screen is touched.

ACC INDICATOR

This test is able to check indicator in push-ignition switch operation.
Indicator in push-ignition switch (ACC) illuminates when “ON” on CONSULT-III screen is touched.

IGNITION ON IND

This test is able to check indicator in push-ignition switch operation.
Indicator in push-ignition switch (ON) illuminates when “ON” on CONSULT-III screen is touched.

KEY SLOT ILLUMI

This test is able to check key slot illumination operation.
Key slot illumination blinks when “ON” on CONSULT-III screen is touched.

DLK-58

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM)

TRUNK : CONSULT-III Function (BCM - TRUNK)

INFOID:0000000005239520

BCM CONSULT-III FUNCTION

CONSULT-III performs the following functions via CAN communication with BCM.

DATA MONITOR

*: With back door opener system

ACTIVE TEST

Diagnosis mode

Function Description

DATA MONITOR

The BCM input/output signals are displayed.

ACTIVE TEST

The signals used to activate each device are forcibly supplied from BCM.

Monitor Item

Contents

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch.

UNLK SEN -DR

NOTE:
This item is displayed, but cannot be monitored. 

VEH SPEED 1

Indicates [Km/h] condition of vehicle speed signal from combination meter.

KEY CYL SW-TR

NOTE:
This item is displayed, but cannot be monitored. 

TR CANCEL SW

NOTE:
This item is displayed, but cannot be monitored. 

TR/BD OPEN SW

Indicates [ON/OFF] condition of back door opener switch.

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored. 

RKE-TR/BD*

NOTE:
This item is displayed, but cannot be monitored. 

Test item

Description

TRUNK/GLASS HATCH

This test is able to check back door opener actuator open operation.

 

 

 

 

 

 

 

Content   ..  481  482  483  484   ..