Infiniti FX35, FX50 (S51). Manual - part 406

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  404  405  406  407   ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 406

 

 

CCS-444

< BASIC INSPECTION >

[LDW & LDP]

ACTION TEST

>> WORK END

72 (45) or 

more

Close to lane marker

Warning and yawing
• Buzzer sounds
• Warning lamp blinks
• Brake control

Short continu-

ous beeps

• Close to lane marker
• Turn signal ON (Deviate 

side)

No action

Close to lane marker with 
soft braking

Warning
• Buzzer sounds
• Warning lamp blinks

Short continu-

ous beeps

VDC OFF switch:
OFF 

 ON

Cancellation
• Buzzer sounds
• Indicator lamp blinks
NOTE:
When LDP switch is ON 

 

OFF, indicator lamp is turned 
OFF.

Beep

Snow mode switch:
OFF 

 ON

(If equipped)

Cancellation
• Buzzer sounds
• Indicator lamp blinks
NOTE:
When LDP switch is ON 

 

OFF, indicator lamp is turned 
OFF.

Beep

Input

Output

Vehicle speed

[km/h (MPH)]

Vehicle condition/ Driver's 

operation

Action

Indication on the combination meter

Buzzer

JPOIA0022GB

JPOIA0021GB

JPOIA0022GB

JPOIA0023GB

JPOIA0023GB

CCS

INSPECTION AND ADJUSTMENT

CCS-445

< BASIC INSPECTION >

[LDW & LDP]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (LANE CAMERA
UNIT)

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (LANE CAMERA 
UNIT) : Description

INFOID:0000000005502057

Always perform the camera aiming adjustment after replacing the lane camera unit.

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (LANE CAMERA 
UNIT) : Special Repair Requirement

INFOID:0000000005502058

1.

CAMERA AIMING ADJUSTMENT

Perform the camera aiming adjustment with CONSULT-III. Refer to 

CCS-445, "CAMERA AIMING ADJUST-

MENT : Description"

.

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

Perform the self-diagnosis of lane camera unit with CONSULT-III. Check if any DTC is detected.

Is any DTC detected?

YES

>> Perform the trouble diagnosis for the detected DTC. Refer to 

CCS-516, "DTC Index"

.

NO

>> GO TO 3.

3.

LDW/LDP SYSTEM ACTION TEST

1.

Perform the LDW/LDP system action test. Refer to 

CCS-442, "Description"

.

2.

Check that the LDW/LDP system operates normally.

>> WORK END

CAMERA AIMING ADJUSTMENT

CAMERA AIMING ADJUSTMENT : Description

INFOID:0000000005502059

OUTLINE

Perform the camera aiming every time the lane camera unit is removed and installed.

CAUTION:

• Place the vehicle on level ground when the camera aiming adjustment is operated.
• Follow the CONSULT-III when performing the camera aiming. (Camera aiming adjustment cannot be

operated without CONSULT-III.)

CAMERA AIMING ADJUSTMENT : Special Repair Requirement (Preparation)

INFOID:0000000005502060

1.

PERFORM SELF-DIAGNOSIS

Perform self-diagnosis of lane camera unit.
Is any DTC detected?

Except “C1B01”>>Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to

CCS-516, "DTC Index"

.

“C1B01” or no DTC>>GO TO 2.

2.

PREPARATION BEFORE CAMERA AIMING ADJUSTMENT

1.

Perform pre-inspection for diagnosis. Refer to 

CCS-441, "Inspection Procedure"

.

2.

Adjust the tire pressure to the specified pressure value.

3.

Maintain no-load in vehicle.

4.

Check if coolant and Engine oil are filled up to correct level and fuel tank is full.

5.

Shift the selector lever to “P” position and release the parking brake.

CCS-446

< BASIC INSPECTION >

[LDW & LDP]

INSPECTION AND ADJUSTMENT

6.

Clean the windshield.

7.

Completely clear off the instrument panel. 

>> GO TO 3.

3.

 PREPARATION OF AIMING ADJUSTMENT JIG

Prepare the aiming adjustment jig according to the following procedure and the figure.
1.

Print out the target mark attached in this SM. Refer to 

CCS-449, "CAMERA AIMING ADJUSTMENT : Spe-

cial Repair Requirement (Target Mark Sample)"

.

2.

Stick a printed target mark on the board with a scotch tape or a piece of double-sided tape.
NOTE:
• Use the board that peripheral area of the target is monochrome such as a white-board.
• Notice that the cross of the target is horizontal and vertical.

>> Go to 

CCS-446, "CAMERA AIMING ADJUSTMENT : Special Repair Requirement (Target Set-

ting)"

.

CAMERA AIMING ADJUSTMENT : Special Repair Requirement (Target Setting)

INFOID:0000000005502061

CAUTION:

• Perform this operation in a horizontal position where there is a clear view for 5 m (16.4 ft) forward

and 3 m (9.84 ft) wide.

• Place the target in a well-lighted location. (Poor lighting may make it hard to adjust.)
• The target may not be detected when there is a light source within 1.5 m (4.92 ft) from either side and

within 1 m (3.28 ft) upward/downward from the target.

• Check the location of the sun. (Sunlight should not shine directly on the front of the vehicle.)
• The target may not be detected when there is the same pattern of black and white as the target when

the pattern is within 1 m (3.28 ft) from either side and upward/downward position from the target. (It
is desirable that the vehicle is positioned on the opposite side of a single-color wall.)

1.

TARGET SETTING

1.

Board

2.

String

3.

Cone

: Target mark

Diameter of a target (D)

: 200 mm (7.87 in)

Height of a target center (H)

: 1450 mm (57.09 in)

Width between a right target cen-
ter from a left target center (W)

: 600 mm (23.62 in)

JPOIA0011ZZ

CCS

INSPECTION AND ADJUSTMENT

CCS-447

< BASIC INSPECTION >

[LDW & LDP]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

1.

Mark points “A”, “B”, “C” and “D”at the center of the lateral sur-
face of each wheels.
NOTE:
Hang a string with a cone from the fender so as to pass through
the center of wheel, and then mark a point at the center of the
lateral surface of the wheel.

2.

Draw line “LH” passing through points “A” and “B” on the left side
of vehicle. 
NOTE:
Approximately 4 m (13.12 ft) or more from the front end of vehi-
cle.

3.

Mark point “E” on the line “LH” at the positions 3850 mm (151.57
in) from point “A”.

4.

Draw line “RH” passing through points “C” and “D” on the right side of vehicle in the same way as step 2.
NOTE:
Approximately 4 m (13.12 ft) or more from the front end of vehicle.

5.

Mark point “F” on the line “RH” at the positions 3850 mm (151.57 in) from point “C”.

6.

Draw line “FW” passing through the points “E” and “F” on the front side of vehicle.

7.

Mark point “X” at the center of point “E” and “F” on the line “FW”.

CAUTION:

Make sure that “E” to “X” is equal to “F” to “X”.

8.

Position the center of the right target to point of “X”.

>> Go to 

CCS-447, "CAMERA AIMING ADJUSTMENT :

Special Repair Requirement (Camera Aiming Adjust-
ment)"

.

CAMERA AIMING ADJUSTMENT : Special Repair Requirement (Camera Aiming Ad-
justment)

INFOID:0000000005502062

CAUTION:

Perform the adjustment under unloaded vehicle condition.

“A” – “E” (“C” – “F”) 

: 3850 mm (151.57 in) 

PKIB4694E

JPOIA0172GB

JPOIA0173GB

 

 

 

 

 

 

 

Content   ..  404  405  406  407   ..