Infiniti FX35, FX50 (S51). Manual - part 1974

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1972  1973  1974  1975   ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 1974

 

 

FRONT WASHER NOZZLE AND TUBE

WW-119

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

Insert a needle or similar object (A) into the spray opening (1) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin.

JPLIA1230ZZ

WW-120

< REMOVAL AND INSTALLATION >

FRONT WIPER ARM AND BLADE

FRONT WIPER ARM AND BLADE

Exploded View

INFOID:0000000005234796

Removal and Installation

INFOID:0000000005234797

REMOVAL

1.

Operate the front wiper to move it to the auto stop position.

2.

Open the hood.

3.

Remove the front wiper arm caps.

4.

Remove the front wiper arm mounting nuts.

5.

Raise front wiper arm, and remove front wiper arm from the vehicle.

INSTALLATION

1.

Clean wiper arm mount as shown in the figure to prevent nuts
from being loosened.

2.

Operate the front wiper motor to move the front wiper to the auto
stop position.

3.

Adjust the front wiper blade position. Refer to 

WW-120, "Adjust-

ment"

.

4.

Install the front wiper arm by tightening the mounting nuts.

5.

Inject the washer fluid.

6.

Operate the front wiper to move it to the auto stop position.

7.

Check that the front wiper blades stop at the specified position.

8.

Install the front wiper arm caps.

Adjustment

INFOID:0000000005234798

WIPER BLADE POSITION ADJUSTMENT

Clearance between the end of cowl top cover and the top of wiper blade center

1.

Front wiper blade (RH)

2.

Front wiper arm (RH)

3.

Front wiper blade (LH)

4.

Front wiper arm (LH)

5.

Front wiper arm cap

Refer to 

GI-4, "Components"

 for symbols in the figure.

JPLIA1231GB

ELH0717D

FRONT WIPER ARM AND BLADE

WW-121

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

Standard clearance

Replacement

INFOID:0000000005234799

FLAT BLADE REFILL

1.

Remove the wiper blade from wiper arm.

2.

Pick up the blade refill rear end to direction (A), pull out the
wiper blade refill to direction (B).

CAUTION:

Never use excessive force to pull the blade refill out. The
blade refill may be torn.

3.

Insert a tip of new blade refill (“LOCK” mark is blade refill rear
end) from the wiper blade rear end. And then slide until the hole
of the blade refill fits in the tab of the wiper blade.
NOTE:
Confirm that “ ” mark (Wiper blade side) fits to “LOCK” mark
(Blade refill side).

4.

Confirm that an installation condition of the blade refill.

5.

Install the wiper blade to the wiper arm.

R

: 72.2

±

7.5 mm (2.843 

±

 0.295 in)

L

: 60.6

±

7.5 mm (2.386 

±

 0.295 in)

JPLIA0082ZZ

JSLIA0145ZZ

JSLIA0146ZZ

WW-122

< REMOVAL AND INSTALLATION >

FRONT WIPER DRIVE ASSEMBLY

FRONT WIPER DRIVE ASSEMBLY

Exploded View

INFOID:0000000005234800

REMOVAL

DISASSEMBLY

Removal and Installation

INFOID:0000000005234801

REMOVAL

1.

Remove the front wiper arm. Refer to 

WW-120, "Exploded View"

.

2.

Remove the cowl top cover. Refer to 

EXT-22, "Exploded View"

.

3.

Remove the bolts from the front wiper drive assembly.

1.

Front wiper drive assembly

JPLIA1232ZZ

1.

Front wiper linkage 1

2.

Shaft seal

3.

Front wiper motor

4.

Front wiper frame

5.

Front wiper linkage 2

: Multi

purpose grease or an equivalent.

JPLIA1233ZZ

 

 

 

 

 

 

 

Content   ..  1972  1973  1974  1975   ..