Infiniti FX35, FX50 (S51). Manual - part 1840

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1838  1839  1840  1841   ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 1840

 

 

A/T POSITION

TM-167

< PERIODIC MAINTENANCE >

[7AT: RE7R01A (VQ35HR)]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

A/T POSITION

Inspection and Adjustment

INFOID:0000000005250150

INSPECTION

1.

Place selector lever in “P” position, and turn ignition switch ON (engine stop).

2.

Check that selector lever can be shifted to other than “P” position when brake pedal is depressed. Also
check that selector lever can be shifted from “P” position only when brake pedal is depressed.

3.

Shift the selector lever and check for excessive effort, sticking, noise or rattle.

4.

Confirm that the selector lever stops at each position by feeling the engagement when it is moved through
all the positions. Check whether or not the actual position the selector lever matches the position shown
by the shift position indicator and the A/T body.

5.

The method of operating the lever to individual positions cor-
rectly is shown in the figure.

6.

When selector button is pressed in “P”, “R”, or “N” position with-
out applying forward/backward force to selector lever, check but-
ton operation for sticking.

7.

Confirm that the back-up lamps illuminate only when lever is
placed in the “R” position. Confirm that the back-up lamps do not
illuminate when selector lever is pushed against “R” position in
the “P” or “N” position.

8.

Confirm that the engine can only be started with the selector
lever in the “P” and “N” positions. (With selector lever in the “P”
position, engine can be started even when selector lever is
moved forward and backward.)

9.

Make sure that A/T is locked completely in “P” position.

10. DS mode must be indicated on the combination meter when the selector lever is shifted to the manual

shift gate. When the selector lever is shifted to the “+” or “

” side in the DS mode, manual mode should be

indicated on the combination meter.
In addition, a set shift position must be changed when the selector lever is shifted to the “+” or “

” side in

the manual mode. (Only while driving.)

ADJUSTMENT

1.

Loosen nut (

).

2.

Place manual lever and selector lever in “P” position.

3.

While pressing lower lever (A) toward rear of vehicle (in “P” posi-
tion direction), tighten nut to specified torque. Refer to 

TM-168,

"Exploded View"

.

CAUTION:

Be careful not to touch the control rod while pressing lower
lever of A/T shift selector assembly.
NOTE:
Press lower lever of A/T shift selector assembly with a force of
approximately 1 kg (9.8 N).

JSDIA0790GB

JPDIA0885ZZ

TM-168

< REMOVAL AND INSTALLATION >

[7AT: RE7R01A (VQ35HR)]

A/T SHIFT SELECTOR

REMOVAL AND INSTALLATION

A/T SHIFT SELECTOR

Exploded View

INFOID:0000000005250151

JSDIA1352GB

A/T SHIFT SELECTOR

TM-169

< REMOVAL AND INSTALLATION >

[7AT: RE7R01A (VQ35HR)]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Removal and Installation

INFOID:0000000005250152

REMOVAL

1.

Shift the selector lever to “P” position.

2.

Remove control rod from A/T shift selector.

3.

Shift the selector lever to “N” position.

4.

Remove knob cover (A) below selector lever downward.

5.

Pull lock pin (1) out of selector lever knob (2).

6.

Remove selector lever knob.

7.

Remove center console assembly. Refer to 

IP-22, "Exploded

View"

.

CAUTION:

When disconnecting selector lever position indicator con-
nector from shift position switch, never twist or apply an
excessive load to the connector.

8.

Remove rear ventilator duct 1. Refer to 

VTL-11, "Exploded

View"

.

9.

Disconnect A/T shift selector harness connector.

10. Remove harness clips from A/T shift selector assembly.

11. Shift the selector lever to “P” position.

12. Remove A/T shift selector assembly mounting bolts.
13. Slightly lift the A/T shift selector assembly (1) and slide it right-

ward. Then pull it out in the diagonally right direction.

14. Remove adapter from A/T shift selector assembly.
15. Remove dust cover and dust cover plate from A/T shift selector

assembly.

16. Remove dust cover from dust cover plate.
17. Remove shift lock unit from A/T shift selector assembly.

18. Remove brackets from vehicle floor panel.

19. Remove selector lever position indicator from console finisher

assembly.

a.

Remove indicator assembly from console finisher assembly.
Refer to 

IP-22, "Exploded View"

.

b.

Remove insert finisher from indicator assembly.

c.

Remove selector lever position indicator.

INSTALLATION

CAUTION:

Apply multi-purpose grease on the pin surface (that slides after installing a collar) of the pivot pin.
Note the following, and Install in the reverse order of removal.
• Refer to the followings when installing selector lever knob to A/T shift selector assembly.
1.

Insert lock pin to selector lever knob.

2.

Install selector lever knob over selector lever until a click is felt.

CAUTION:

1.

Selector lever knob

2.

Lock pin

3.

Indicator plate

4.

Selector lever position indicator

5.

Harness connector

6.

Insert finisher

7.

Control rod

8.

Dust cover

9.

Bracket

10.

Dust cover plate

11.

Snap pin

12.

Washer

13.

Collar

14.

Pivot pin

15.

Insulator

16.

Shift lock unit

17.

A/T shift selector assembly

18.

Adapter

: Apply multi-purpose grease.

Refer to 

GI-4, "Components"

 for symbols not described on the above.

JPDIA0898ZZ

JPDIA0055ZZ

TM-170

< REMOVAL AND INSTALLATION >

[7AT: RE7R01A (VQ35HR)]

A/T SHIFT SELECTOR

• Install it straight, and never tap or apply any shock to install it.
• Never press selector button.

• When installing control rod to A/T shift selector assembly, refer to “ADJUSTMENT”. Refer to 

TM-167,

"Inspection and Adjustment"

.

Inspection and Adjustment

INFOID:0000000005250153

INSPECTION AFTER INSTALLATION

Check A/T positions after adjusting A/T positions. Refer to 

TM-167, "Inspection and Adjustment"

.

ADJUSTMENT AFTER INSTALLATION

Adjust A/T positions. Refer to 

TM-167, "Inspection and Adjustment"

.

 

 

 

 

 

 

 

Content   ..  1838  1839  1840  1841   ..