Infiniti FX35, FX50 (S51). Manual - part 1838

PREPARATION

TM-159

< PREPARATION >

[7AT: RE7R01A (VQ35HR)]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

PREPARATION

PREPARATION

Commercial Service Tool

INFOID:0000000005250144

*: Always check with the Parts Department for the latest parts information.

Tool number
Tool name

Description

1.

315268E000*
O-ring

2.

310811EA5A*
Charging pipe

A/T fluid changing and adjustment

Power tool

Loosening bolts and nuts

JSDIA1332ZZ

PBIC0190E

TM-160

< PERIODIC MAINTENANCE >

[7AT: RE7R01A (VQ35HR)]

A/T FLUID

PERIODIC MAINTENANCE

A/T FLUID

Changing

INFOID:0000000005250145

CAUTION:

• Use only Genuine NISSAN Matic S ATF. Never mix with other ATF.
• Using ATF other than Genuine NISSAN Matic S ATF will cause deterioration in driveability and A/T

durability, and may damage the A/T, which is not covered by the INFINITI new vehicle limited war-
ranty.

• When filling ATF, be careful not to scatter heat generating parts such as exhaust.

1.

Step 1

a.

Install the O-ring (315268E000) (A) to the charging pipe
(310811EA5A) (B).

2.

Step 2

a.

Use CONSULT-III to check that the ATF temperature is 40

°

C (104

°

F) or less.

b.

Lift up the vehicle.

c.

Remove the drain plug from the oil pan, and then drain the ATF.

d.

When the ATF starts to drip, temporarily tighten the drain plug to the oil pan.
NOTE:
Never replace drain plug and drain plug gasket with new ones yet.

e.

Remove overflow plug from oil pan.

f.

Install the charging pipe (A) to the overflow plug hole.

CAUTION:

Tighten the charging pipe by hand.

g.

Install the bucket pump hose (B) to the charging pipe.

CAUTION:

Insert the bucket pump hose all the way to the end of the
charging pipe.

h.

Fill approximately 3 liters (3-1/8 US qt, 2-5/8 lmp qt) of the ATF.

i.

Remove the bucket pump hose to remove the charging pipe,
and then temporarily tighten the overflow plug to the oil pan.

CAUTION:

Quickly perform the procedure to avoid ATF leakage from
the oil pan.

j.

Lift down the vehicle.

k.

Start the engine and wait for approximately 3 minutes.

l.

Stop the engine.

3.

Step 3

a.

Repeat “Step 2”.

4.

Final Step

ATF

: Refer to 

TM-187, "General Specification"

.

Fluid capacity

: Refer to 

TM-187, "General Specification"

.

JSDIA1334ZZ

JSDIA1335ZZ

A/T FLUID

TM-161

< PERIODIC MAINTENANCE >

[7AT: RE7R01A (VQ35HR)]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

a.

Use CONSULT-III to check that the ATF temperature is 40

°

C (104

°

F) or less.

b.

Lift up the vehicle.

c.

Remove the drain plug from the oil pan, and then drain the ATF.

d.

When the ATF starts to drip, tighten the drain plug to the oil pan to the specified torque. Refer to 

TM-172,

"Exploded View"

.

CAUTION:

Never reuse drain plug and drain plug gasket.

e.

Remove overflow plug from oil pan.

f.

Install the charging pipe (A) to the overflow plug hole.

CAUTION:

Tighten the charging pipe by hand.

g.

Install the bucket pump hose (B) to the charging pipe.

CAUTION:

Insert the bucket pump hose all the way to the end of the
charging pipe.

h.

Fill approximately 3 liters (3-1/8 US qt, 2-5/8 lmp qt) of the ATF.

i.

Remove the bucket pump hose to remove the charging pipe,
and then temporarily tighten the overflow plug to the oil pan.

CAUTION:

Quickly perform the procedure to avoid ATF leakage from
the oil pan.

j.

Lift down the vehicle.

k.

Start the engine.

l.

Make the ATF temperature approximately 40

°

C (104

°

F).

NOTE:
The ATF level is greatly affected by the temperature. Always check the ATF temperature on “ATF TEMP
1” of “Data Monitor” using CONSULT-III.

m. Park vehicle on level surface and set parking brake.

n.

Shift the selector lever through each gear position. Leave selector lever in “P” position.

o.

Lift up the vehicle when the ATF temperature reaches 40

°

C (104

°

F), and then remove the overflow plug

from the oil pan.

p.

When the ATF starts to drip, tighten the overflow plug to the oil pan to the specified torque. Refer to 

TM-

172, "Exploded View"

.

CAUTION:

Never reuse overflow plug.

Adjustment

INFOID:0000000005250146

CAUTION:

• Use only Genuine NISSAN Matic S ATF. Never mix with other ATF.
• Using ATF other than Genuine NISSAN Matic S ATF will cause deterioration in driveability and A/T

durability, and may damage the A/T, which is not covered by the INFINITI new vehicle limited war-
ranty.

• When filling ATF, be careful not to scatter heat generating parts such as exhaust.
• Always maintain the ATF temperature within between 35

°

C (95

°

F) and 45

°

C (113

°

F) while checking

with CONSULT-III when the ATF level adjustment is performed.

JSDIA1335ZZ

ATF

: Refer to 

TM-187, "General Specification"

.

Fluid capacity

: Refer to 

TM-187, "General Specification"

.

TM-162

< PERIODIC MAINTENANCE >

[7AT: RE7R01A (VQ35HR)]

A/T FLUID

1.

Install the O-ring (315268E000) (A) to the charging pipe
(310811EA5A) (B).

2.

Start the engine.

3.

Make the ATF temperature approximately 40

°

C (104

°

F).

NOTE:
The ATF level is greatly affected by the temperature. Always
check the ATF temperature on “ATF TEMP 1” of “Data Monitor”
using CONSULT-III.

4.

Park vehicle on level surface and set parking brake.

5.

Shift the selector lever through each gear position. Leave selec-
tor lever in “P” position.

6.

Lift up the vehicle.

7.

Check the ATF leakage from transmission.

8.

Remove overflow plug from oil pan.

9.

Install the charging pipe (A) to the overflow plug hole.

CAUTION:

Tighten the charging pipe by hand.

10. Install the bucket pump hose (B) to the charging pipe.

CAUTION:

Insert the bucket pump hose all the way to the end of the
charging pipe.

11. Fill approximately 0.5 liters (1/2 US qt, 1/2 lmp qt) of the ATF.

12. Check that the ATF leaks when removing the charging pipe and

the bucket pump hose. If the ATF does not leak, refill the ATF.

13. When the ATF starts to drip, tighten the overflow plug to the oil

pan to the specified torque. Refer to 

TM-172, "Exploded View"

.

CAUTION:

Never reuse overflow plug.

JSDIA1334ZZ

JSDIA1335ZZ