Infiniti FX35, FX50 (S51). Manual - part 1720

B1037, B1039, B1041 CRASH ZONE SENS1

SRC-45

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1037, B1039, B1041 CRASH ZONE SENS1

Description

INFOID:0000000005241094

Main “G” sensor generates signal voltage, when it detects deceleration beyond the specified level caused by
vehicle frontal collision.

OPERATION

When air bag diagnosis sensor unit defines both signal voltage of the “G” sensor and the safing algorithm to
be that of collision which exceeds a specified level, the driving circuit switches on and feeds the electric ignitor
of both driver and passenger air bags and pre-tensioner seat belts.

STRUCTURE

Integrated type of the “G” sensor element for frontal collision with output terminals for signal voltage.

INSTALLATION

Crash zone sensor is installed on the radiator core support assembly with fixed nuts.

DTC Logic

INFOID:0000000005241095

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-16, "Air Bag Warning Lamp Diagnosis"

.

NOTE:
SRS does not enter diagnosis mode if no malfunction is detected in user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-45, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005241096

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1037
B1039
B1041

CRASH ZONE 
SENSOR1 

Crash zone sensor is malfunctioning

• Disconnection of wiring harness
• Malfunction in crash zone sensor
• Malfunction in air bag diagnosis sen-

sor unit

SRC-46

< DTC/CIRCUIT DIAGNOSIS >

B1037, B1039, B1041 CRASH ZONE SENS1

3.

REPLACE CRASH ZONE SENSOR

1.

Replace crash zone sensor. Refer to 

SR-21, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-45, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-25, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-45, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

B1042, B1043, B1044, B1045, B1046, B1047 DIAGNOSIS SENSOR UNIT

SRC-47

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1042, B1043, B1044, B1045, B1046, B1047 DIAGNOSIS SENSOR UNIT

Description

INFOID:0000000005241097

Checks the entire SRS and displays the malfunction either by illuminating or blinking the air bag warning lamp
on the combination meter. Malfunctioning part can be detected by on board self-diagnosis system and CON-
SULT-III.

OPERATION

It detects a shock that exceeds a specified level and monitors whether the driver and passenger air bags, front
side air bag, side curtain air bag and pre-tensioner seat belts operate normally. 

STRUCTURE

It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.

INSTALLATION

Air bag diagnosis sensor unit is installed under the center console with fixed bolts.

DTC Logic

INFOID:0000000005241098

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-16, "Air Bag Warning Lamp Diagnosis"

.

NOTE:
SRS does not enter diagnosis mode if no malfunction is detected in user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-47, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005241099

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1042
B1043
B1044
B1045
B1046
B1047

CONTROL UNIT 

Air bag diagnosis sensor unit is mal-
functioning or out of the specification

• Malfunction in air bag diagnosis sen-

sor unit

• Configuration in air bag diagnosis 

sensor unit does not match the vehi-
cles specification

SRC-48

< DTC/CIRCUIT DIAGNOSIS >

B1042, B1043, B1044, B1045, B1046, B1047 DIAGNOSIS SENSOR UNIT

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-25, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-47, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END