Content .. 1378 1379 1380 1381 ..

Infiniti FX35, FX50 (S51). Manual - part 1380

MWI

COMPASS

MWI-39

< SYSTEM DESCRIPTION >

COMPASS

Description

INFOID:0000000005524593

DESCRIPTION

• This electronic compass is able to display 8 primary directions: N, NE, E, SE, S, SW, W, NW.
• The compass switch (1) is used to operate the compass.

Switch Operation

• All standard compasses determine direction relative to magnetic north; however, this electronic compass is

designed to display direction relative to true north.

• The difference between magnetic north and true north varies from place to place across the surface of the

earth.

• This electronic compass must be “told” approximately where it is on the earth’s surface so that the magnetic

north reading can be properly converted into a true north display.

• To tell the electronic compass where it’s at, the earth is separated into numbered “zone variances”. The zone

variance number in which the compass is to function must be entered into this electronic compass.

• Each zone is magnetically about 4.2

wide. Typically, anything under 22.5

total zone change is not noticed

on the electronic compass display. However, over 22.5

, a reading may be off by one or more primary direc-

tions.

• On long trips, a vehicle may leave its original zone and enter one or more new zones. Generally, you do not

need to reset the compass zone if you travel between 3 or 4 zones, such as business travel or vacation. The
typical driver will not notice any difference on the display within 3 or 4 zones. However, if the vehicle is “per-
manently” moved to a new location, it is recommended that the compass zone be reset.

ZONE VARIATION SETTING PROCEDURE

SKIB8868E

Press

Compass is turned ON/OFF

Press and hold
(for 3- 9 sec.)

Compass display (2) turns to zone variation change
mode Compass

Press and hold (for more
than 9 sec.)

Compass display turns to calibration mode

MWI-40

< SYSTEM DESCRIPTION >

COMPASS

Press and hold the compass switch for 3 – 9 seconds.

The current zone setting appears on the compass display.

Find the current geographical location number in the zone varia-
tion chart.

Select the new zone number. (Press the compass switch until
the new zone number appears on the compass display.)

After select the new zone number, the compass display will
automatically shows a direction within a few seconds.

Perform the following calibration procedure for more accurate
indications.

CALIBRATION PROCEDURE

NOTE:
The compass calibrates itself under normal driving conditions. However, occasional circumstances may cause
the compass to operate inaccurately. Example: Driving from rural (wide open) areas to crowded city areas, or
if an aftermarket (i.e., non original equipment) antenna with a magnetic base is attached to the vehicle. Cali-
brate the mirror compass if the display shows only one direction or a limited number of directions.
NOTE:
• If “magnetic hats” are used in the dealership for vehicle identification, remove the hat from the vehicle before

performing the following steps. Do not put the hat back on the vehicle after the procedure is completed.

• Drive the vehicle to an open level area; away from large metallic objects, structures, and overhead power

lines.

• Turn off “non-essential” electrical accessories (rear window defrost, heater/air conditioning, wipers) and

close the doors.

Verify the correct compass zone setting for the geographical location.

Press and hold the compass switch for more than 9 seconds.

“C“ is displayed on the compass display, when calibration starts.

Drive slowly [less than 8 km/h (5 MPH)] in a circle until the “C / CAL” is replaced with primary headings (N,
NE, E, SE, S, SW, W, or NW).
NOTE:
This will require driving at least 2 complete 360 degree circles; 3 complete circles may be required.

The compass calibration procedure is now complete. The compass should operate normally.
NOTE:
If at any time the compass continually displays the incorrect direction or the reading is erratic or locked,
repeat the calibration procedure.

SEL168Y